Thingiverse
Additions and modifications for HyperCube Evolution by TunnelVision
by Thingiverse
Last crawled date: 4 years, 7 months ago
E3D Titan Aero mount
Using a Titan Aero adds width to the X assembly and reduces X travel compared to the standard design; the amount depends on the motor and fan used. With a 20.7mm motor and 7mm fan I am limited to 295mm of travel in X with approx 1.5mm clearance either side. My frame extrusions and shafts are based on 300x300x300mm in the configuration spreadsheet. That gives an idea of how much X travel to add for anyone planning to use this extruder.
Some examples:
20.7mm motor, 10mm (stock) fan - add 3 + 5 = 8mm minimum (I would round that up to 10mm)
25mm motor, 10mm fan - add 3 + 4.3 + 5 = 12.3mm (or round up to 15mm)
E3D_TA_X_Carriage
There are two additional bosses on the back side of the carriage for threaded inserts; these are used to mount the fan duct. If you don't need a part cooler, you don't need this modified X carriage.
E3D_TA_Mount
E3D_TA_Mount_IR
I will be using the Mini Differential IR sensor (https://miscsolutions.wordpress.com/mini-height-sensor-board/) as a Z-probe. E3D_TA_Mount_IR includes the mounting holes for this.
Version 1.1 (E3D_TA_Mount_IR_1.1) adds cable support and removes the X max optical end stop.
E3D_TA_Fan_Duct_Mount
Uses two more threaded inserts to mount the fan duct.
E3D_TA_Fan_Duct
I printed this in three parts then superglued them together. For now I have omitted the top fan screw because it can contact the back of the frame.
Indicator mount
https://www.youtube.com/watch?v=DO9Y43uxi5g
The mount and clamp work with an 8mm diameter stem as found on the Banggood digital indicator shown in the pictures.
Indicator_Mount_1.1 adds support for the back of the indicator to stop it moving when pressing the zero button. Might only fit this model of indicator.
Indicator_Mount_Y is for checking motion in the Y direction (against the front frame).
X_Indicator_Stop
The indicator mount can be rotated 90° (thanks to the square hole pattern SCOTT_3D uses for the dowel pins) in order to test and calibrate movement in the X direction. This end stop mounts (temporarily) on XY_Stepper_Mount; I used M3x12mm screws. As you lose the X end stops when removing the extruder mount, G92 X10 can be used once the X carriage is jogged into the start position, hopefully preventing crashes.
Step-down module mount
For mounting the e_goto 24 to 12V converters from SCOTT_3D's BOM (https://www.aliexpress.com/item/DC-DC-24V-18V-to-12V-3A-Step-Down-Module-MINI-Buck-Converter-Power-Supply-Circuit/32778770850.html?spm=2114.13010608.0.0.G2tjiK or https://www.aliexpress.com/item/DC-DC-Step-Down-Power-Supply-Buck-Converter-3A-Fixed-Output-14V-28V-to-12V/32636205942.html). 28mm hole spacing for M4 screws.
(Inspired by https://www.thingiverse.com/thing:875468).
Spool_Holder_Clamp_Top/Bottom
I'm using this with a length of M8 threaded rod and
these https://www.thingiverse.com/thing:2532403 spool holders.
Tension_O_Matic
The screws on the X carriage are good for fine-tuning belt tension, as well as squaring the X/Y axes, but this tool should help with overall tension.
Currently for 8mm X-shafts, 45mm X-shaft spacing and 11mm belt spacing. 10mm shaft version (untried, untested) here https://www.dropbox.com/s/xpcaoxigcuwk47n/Tension_O_Matic_10mm_1.1.zip?dl=0.
Changes
03/09/2017 - Added Indicator_Mount_1.1
10/09/2017 - Added X_Indicator_Stop_1.0
13/09/2017 - Added Spool_Holder_Clamp_Top/Bottom_1.0
27/09/2017 - Added Tension_O_Matic
28/09/2017 - Added Indicator_Mount_Y_1.0
04/10/2017 - Added E3D_TA_Mount_IR_1.1
Using a Titan Aero adds width to the X assembly and reduces X travel compared to the standard design; the amount depends on the motor and fan used. With a 20.7mm motor and 7mm fan I am limited to 295mm of travel in X with approx 1.5mm clearance either side. My frame extrusions and shafts are based on 300x300x300mm in the configuration spreadsheet. That gives an idea of how much X travel to add for anyone planning to use this extruder.
Some examples:
20.7mm motor, 10mm (stock) fan - add 3 + 5 = 8mm minimum (I would round that up to 10mm)
25mm motor, 10mm fan - add 3 + 4.3 + 5 = 12.3mm (or round up to 15mm)
E3D_TA_X_Carriage
There are two additional bosses on the back side of the carriage for threaded inserts; these are used to mount the fan duct. If you don't need a part cooler, you don't need this modified X carriage.
E3D_TA_Mount
E3D_TA_Mount_IR
I will be using the Mini Differential IR sensor (https://miscsolutions.wordpress.com/mini-height-sensor-board/) as a Z-probe. E3D_TA_Mount_IR includes the mounting holes for this.
Version 1.1 (E3D_TA_Mount_IR_1.1) adds cable support and removes the X max optical end stop.
E3D_TA_Fan_Duct_Mount
Uses two more threaded inserts to mount the fan duct.
E3D_TA_Fan_Duct
I printed this in three parts then superglued them together. For now I have omitted the top fan screw because it can contact the back of the frame.
Indicator mount
https://www.youtube.com/watch?v=DO9Y43uxi5g
The mount and clamp work with an 8mm diameter stem as found on the Banggood digital indicator shown in the pictures.
Indicator_Mount_1.1 adds support for the back of the indicator to stop it moving when pressing the zero button. Might only fit this model of indicator.
Indicator_Mount_Y is for checking motion in the Y direction (against the front frame).
X_Indicator_Stop
The indicator mount can be rotated 90° (thanks to the square hole pattern SCOTT_3D uses for the dowel pins) in order to test and calibrate movement in the X direction. This end stop mounts (temporarily) on XY_Stepper_Mount; I used M3x12mm screws. As you lose the X end stops when removing the extruder mount, G92 X10 can be used once the X carriage is jogged into the start position, hopefully preventing crashes.
Step-down module mount
For mounting the e_goto 24 to 12V converters from SCOTT_3D's BOM (https://www.aliexpress.com/item/DC-DC-24V-18V-to-12V-3A-Step-Down-Module-MINI-Buck-Converter-Power-Supply-Circuit/32778770850.html?spm=2114.13010608.0.0.G2tjiK or https://www.aliexpress.com/item/DC-DC-Step-Down-Power-Supply-Buck-Converter-3A-Fixed-Output-14V-28V-to-12V/32636205942.html). 28mm hole spacing for M4 screws.
(Inspired by https://www.thingiverse.com/thing:875468).
Spool_Holder_Clamp_Top/Bottom
I'm using this with a length of M8 threaded rod and
these https://www.thingiverse.com/thing:2532403 spool holders.
Tension_O_Matic
The screws on the X carriage are good for fine-tuning belt tension, as well as squaring the X/Y axes, but this tool should help with overall tension.
Currently for 8mm X-shafts, 45mm X-shaft spacing and 11mm belt spacing. 10mm shaft version (untried, untested) here https://www.dropbox.com/s/xpcaoxigcuwk47n/Tension_O_Matic_10mm_1.1.zip?dl=0.
Changes
03/09/2017 - Added Indicator_Mount_1.1
10/09/2017 - Added X_Indicator_Stop_1.0
13/09/2017 - Added Spool_Holder_Clamp_Top/Bottom_1.0
27/09/2017 - Added Tension_O_Matic
28/09/2017 - Added Indicator_Mount_Y_1.0
04/10/2017 - Added E3D_TA_Mount_IR_1.1