Thingiverse
Printrbot Simple, 300mm Y Axis-No Sag! by iamjonlawrence
by Thingiverse
Last crawled date: 2 years, 10 months ago
Upgrade your Y axis to 300 mm (12") or more or less, GT2 belt drive, and eliminate Y-Sag in one mod...
I upgraded to 300 mm capacity here only because I had a piece of 8 mm rod 915 mm (36") long and didn't want to waste it. Not to mention "just because I can." I am currently only using 150 mm to reach the edge of my 6" heat bed, but have run it all the way out and it is extremely stable over the entire distance. Rod & belt lengths can be adjusted to whatever you dare. Only requirement is that the lower rod is 50 mm (2") longer than the top.
Increased linear bearing centers from the stock 24 mm to 64 mm. What this means is 3x the overhang possible, effectively eliminating Y-sag common to the Simple. I was surprised at how solid the Y axis is now.
Designed to hold stock wooden direct drive extruder. Not tested with aluminum DDE.
Requirements:
95 mm x 95 mm print area
The ability to print FLAT without edges lifting
Well calibrated printer
GT2 20 tooth belt pulley. 18 tooth will not clear bearing
Z axis Hex nut to measure 1/2" across flats
Y/X axis at 90 degrees.
2014-02-19, REV.B: Added ZScrewMount for printers purchased after 10/23/2013 where they changed the Z screw assembly. Also changed Z Endstop Extension to a better design.
2014-03-17, REV.C: Modified Z nut mounting to accomodate ACME nut. Uploaded new version of ExtendYPlate.stl as ExtendYPlateRevC.stl.
2014-03-23: Uploaded front plate for 2014 Simple fan and aluminum extruder. "ExtendYFront2014AlExtruder.stl"
2014-03-24: Uploaded front plate for 2014 Simple, Fan, Aluminum extruder, and Cable management. "ExtendYFront2014AlExtruderCable.STL"
2014-03-25: Updated "ExtendYFront2014ExtruderCable.stl" to "ExtendYFront2014ExtruderCableRevA.stl" which includes mounting for a bolt on fan duct extension. Also uploaded "ExtendYFanDuct.stl" as the extension piece for the fan duct.
2014-04-02: Uploaded a version of the front end for the 2013 Simple that includes a side mounted fan like the 2014. "ExtendYFront2013Fan.slt" Use with "ExtendYFanDuct.stl"
2014-04-07: Uploaded a version of the rear end that allows the use of identical length rods. With this rear end the rod lengths need to be at least 175mm longer than your desired stroke.
2014-04-14: Uploaded an updated version of the end stop flag RevA. This will allow you to insert the belt thru the flag and remove some of the belt vibration.
2014-04-17: Uploaded an updated version of the front end for the aluminum extruder that includes some extra supports. "ExtendYFront2014AlExtruderRevA.stl"
2014-05-11: Uploaded a version of the rear end that uses a clamp to secure the rods, and allows the upper rod to pass thru, so equal length rods can be used. "ExtendYRearClamp.stl"
This design was inspired by kingfuroy's Modified Simple http://www.thingiverse.com/thing:238932
Feedback is strongly encouraged.
I upgraded to 300 mm capacity here only because I had a piece of 8 mm rod 915 mm (36") long and didn't want to waste it. Not to mention "just because I can." I am currently only using 150 mm to reach the edge of my 6" heat bed, but have run it all the way out and it is extremely stable over the entire distance. Rod & belt lengths can be adjusted to whatever you dare. Only requirement is that the lower rod is 50 mm (2") longer than the top.
Increased linear bearing centers from the stock 24 mm to 64 mm. What this means is 3x the overhang possible, effectively eliminating Y-sag common to the Simple. I was surprised at how solid the Y axis is now.
Designed to hold stock wooden direct drive extruder. Not tested with aluminum DDE.
Requirements:
95 mm x 95 mm print area
The ability to print FLAT without edges lifting
Well calibrated printer
GT2 20 tooth belt pulley. 18 tooth will not clear bearing
Z axis Hex nut to measure 1/2" across flats
Y/X axis at 90 degrees.
2014-02-19, REV.B: Added ZScrewMount for printers purchased after 10/23/2013 where they changed the Z screw assembly. Also changed Z Endstop Extension to a better design.
2014-03-17, REV.C: Modified Z nut mounting to accomodate ACME nut. Uploaded new version of ExtendYPlate.stl as ExtendYPlateRevC.stl.
2014-03-23: Uploaded front plate for 2014 Simple fan and aluminum extruder. "ExtendYFront2014AlExtruder.stl"
2014-03-24: Uploaded front plate for 2014 Simple, Fan, Aluminum extruder, and Cable management. "ExtendYFront2014AlExtruderCable.STL"
2014-03-25: Updated "ExtendYFront2014ExtruderCable.stl" to "ExtendYFront2014ExtruderCableRevA.stl" which includes mounting for a bolt on fan duct extension. Also uploaded "ExtendYFanDuct.stl" as the extension piece for the fan duct.
2014-04-02: Uploaded a version of the front end for the 2013 Simple that includes a side mounted fan like the 2014. "ExtendYFront2013Fan.slt" Use with "ExtendYFanDuct.stl"
2014-04-07: Uploaded a version of the rear end that allows the use of identical length rods. With this rear end the rod lengths need to be at least 175mm longer than your desired stroke.
2014-04-14: Uploaded an updated version of the end stop flag RevA. This will allow you to insert the belt thru the flag and remove some of the belt vibration.
2014-04-17: Uploaded an updated version of the front end for the aluminum extruder that includes some extra supports. "ExtendYFront2014AlExtruderRevA.stl"
2014-05-11: Uploaded a version of the rear end that uses a clamp to secure the rods, and allows the upper rod to pass thru, so equal length rods can be used. "ExtendYRearClamp.stl"
This design was inspired by kingfuroy's Modified Simple http://www.thingiverse.com/thing:238932
Feedback is strongly encouraged.
Similar models
thingiverse
free
Printrbot Simple X upgrade. by iamjonlawrence
... on the ends of the rods and not bind the bed leveling screws.
design inspired by ahaer http://www.thingiverse.com/thing:215294
thingiverse
free
Fan extension for "Printrbot Simple, 300mm Y Axis-No Sag!" by FablabMoebius
... allows to cool the support, avoiding bending or further distorsion.
this extensions for the printrbot simple after 23/10/2013.
thingiverse
free
Printrbot Original Remix by orangefurball
...extruder mount will be updated to lock the gt2 belts better. the last thing i have to do is make a bolt-on y axis end stop mount.
thingiverse
free
Spacer for aluminum GT2 pulley and fan mount for X axis + Fan mount for Y axis by rafarcarvalho
... had to use a belt tensioner to gain space between the bed and the endstop of the y-axis. https://www.thingiverse.com/thing:10082
thingiverse
free
Timing Belt Y GT2, Printrbot Simple V2 by iamjonlawrence
...y axis of the printrbot simple. this thing is similar to my original http://www.thingiverse.com/thing:180146 differences are: use gt2 belt...
thingiverse
free
Prusa i3 improved XZ axis by jkoljo
... tightener
belt forces carried by x rods, not z rods
4.6.2015: added axis ends that have looser tolerance for 8 mm smooth rod
thingiverse
free
MP Monoprice Select Mini - GT2 Y Belt Tensioner by Vector-3D
...s (ideally locking nuts)
aftermarket gt2 6 mm belt (the stock one works but may be too short)
edit:
added front and rear versions
thingiverse
free
Y-Belt-Holder GT2 by CAPI
...t-holder gt2 by capi
thingiverse
holder for gt2 belt, this is used in prusa i3 axis y, greater length with respect to the base.
thingiverse
free
40mm Extruder Fan Mount for Printrbot Simple, 300mm Y Axis-No Sag! by mrownership
...o sag! (http://www.thingiverse.com/thing:242185) so i decided to make one myself.
pretty straightforward, just print and install.
thingiverse
free
Washer for The Printrbot 300 mm Y axis extension Axis-No Sag! by FablabMoebius
...ww.thingiverse.com/iamjonlawrence/overview)).
my gt2 belt was out of about 2mm. this washer fixed it.
now it works like charm !
Iamjonlawrence
thingiverse
free
1405 Simple X Expanded (Single/Double Precision) by iamjonlawrence
...ined those ideas into a 3d model. please review the conversation:http://www.printrbottalk.com/forum/viewtopic.php?f=21&t=6860
thingiverse
free
1405 300mm No Sag, Printrbot Simple by iamjonlawrence
... heat cartridge (too low).
2014-07-10: uploaded alternate part fan and mount to work with the ubis. may not work with the e3d.
thingiverse
free
PrintrBot 1405 E3D Lite6 Bowden Clamp for No Sag Mod by Shanjaq
...my wooden printrbot 1405 with the no-sag mod by iamjonlawrence so i made this. assuming you have the shroud...
thingiverse
free
Thread Gauge Cone, Standard by phillthomas
...size shown. thread pitches are as shown. thanks to iamjonlawrence for the idea, i saw some folks asking for...
thingiverse
free
Multi-Function Maker Simple Machine by Kannonballer
...the printrbot maker simple and the excellent designs of iamjonlawrence ( jon lawrence ), orangefurball ( matt wahlers )...
thingiverse
free
50mm Extruder Fan Duct / Adapter - Printrbot Simple by ThePerfesser
...does not interfere with the gt2 belt conversion by iamjonlawrence ...
thingiverse
free
Printrbot simple makers edition (1405) ZY Plate for stock Y axis by Zezo
...thingiverse this yz plate was based on measurements from iamjonlawrence designs, and sambert20 remix:http://www.thingiverse.com/thing:372467http://www.thingiverse.com/thing:723004http://www.thingiverse.com/thing:799068 it is a simplified version...
thingiverse
free
Blower Fan to 40MM Fan Mount Adapter by kmckee8372
...designed this to fit:http://www.amazon.com/gp/product/b008p72ssm?psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00 also, this works great with iamjonlawrence#39;s 1405 300mm no sag, printrbot...
thingiverse
free
Printrbot 1405 Front end and YZ plate by MattTheGinge
...yz plate by matttheginge thingiverse a modified version of iamjonlawrence#39;s front end and yz plate that allows for the...
Sag
3d_export
$5
puzzle cube
...tolerance at the bridge location to account for some saging. the bridge length is 22mm. cube size at default...
3d_export
$5
Stylish German chair Johann B125 from Bretz in loft style
...oiled walnut. exceptional seating comfort is provided by the no-sag independent spring system and premium quality polyurethane. the back...
3d_export
$5
Stylish German armchair Johann B125 from Bretz
...oiled walnut. exceptional seating comfort is provided by the no-sag independent spring system and premium quality polyurethane. the back...
thingiverse
free
GPU Support Bracket by robatzen
...bracket to support my gpu and stop it from saging. i use it to hold up my xfx rx...
thingiverse
free
Pi Zero Official Lid Case by Voodle
...micro-usb and mini-hdmi cables to fit even with some saging on the top of the...
thingiverse
free
Noise isolation retainer by Oleg
...oleg thingiverse over time, the insulation under the hood sag. this defect can be corrected with clips that are...
thingiverse
free
fox dhx2 shox spring key by biclou
...spring key by biclou thingiverse key to adjust the sag on your dhx2 follow me for more cool...
thingiverse
free
I-shaped Brace (150mm Long) by aptinstallthingiverse
...shelf unit for another design or to brace a saging shelf an extension for a stand although there is...
thingiverse
free
2020 Dumpster Fire Ornament (Dual Color Dumpster and Angled Fire) by tagno25
...of the flame to try to account for slight saging of the...
thingiverse
free
Wall Mount for Camera Ball-head by u4142020
...has a support rib under the bracket for less sag with heavy cameras, and carved out some of the...
300Mm
3ddd
$1
Бра Brille
...ламп:1 стиль:свеча цвет каркаса:золото материал каркаса:металл торговая марка:brille высота, h:300mm ширина, b:180mm длина,...
3ddd
$1
TableLamp EGLO OSSAGO
...eglo ossago арт. 94461: - размеры: height 505mm, diameter 300mm base diameter 220mm - е27, 1х60w настольная лампа eglo...
3ddd
$1
KUTAHYA SERAMIK AGAT
...комплекте плитка размером wall tile size 95mm x 13532mm 300mm x 3000mm 900mm x 3000mm 3000mm x 3000mm 4520mm...
3ddd
$1
KUTAHYA SERAMIK TALYA
...комплекте плитка размером wall tile size 900mm x 12770mm 300mm x 12770mm 1800mm x 12770mm floor tile size 13640mm...
3ddd
$1
Coffee Table
...glass coffee table measurements: length: 910mm width: 910mm height: 300mm ...
3ddd
$1
Стеллаж
...3ddd стеллаж производитель: индивидуального изготовления модель: стеллаж размеры: w-960mm, d-300mm ...
3ddd
$1
Римские шторы #4
...римская производитель: - модель: римские шторы размеры: w-1000mm, d-85/150mm, h-1825/300mm римская штора с 9 позициями разных...
3ddd
$1
Nana Mobile Hanging Lamp
...creations , nana mobile люстра от aqua creationsвысота свыше 300mm ...
3ddd
$1
mateo
...mateo 3ddd блюдо сервировочные блюда 300mm ...
3ddd
$1
Столб заходной.
...столб классический заходной столб. габариты: 1100mm x 400mm x 300mm моделировалось по фото, автор не известен. колличество полигонов 13...
Printrbot
thingiverse
free
Printrbot Simple Metal 18mm probe holder by nomath4u
...re to update the z-probe offset setting in marlin. my best settings are working with this offset 55mm on the side and that is it.
thingiverse
free
Printrbot Simple Metal Remix of Hybrid Modular Spool Roller by PearlGreyMusic by FossilFolk
...it works great and i like that it's easy to apply just a bit of pressure to the spool to prevent it from unreeling mid print.
thingiverse
free
Godzilla Japanese Printable Embellishments for Fun and Profit! by SpaceMonkeyBoom
...for a magic deck box. printed on an old printrbot 1405....
thingiverse
free
Fan Shroud For Printrbot Simple Pro and Plus Metal by Swood333
...e.
for best results print with the overhangs oriented towards your greatest cooling and set your extrusion width slightly higher.
thingiverse
free
Echo Show 8 Monitor Stand All In One by XtremeDesignz3
...sit on top of your computer monitor. printed on printrbot play with extended y axis and heated bed. print...
thingiverse
free
Printrbot Simple Metal USB Cable Fix and Protector by jsmith24
... that was the easiest way to get it straight.
now just plug the right angle cable into the usb extension and you're all set.
thingiverse
free
Printrbot Simple Metal BLTouch Mount by jtyphoid
...t on.
as with slipjig's version, you will need to cut off the round hoop that is used to mount the original inductive sensor.
thingiverse
free
Durr Burger (Fortnite) by Quinventor
...: https://www.banggood.com/shock-absorber-stepper-motor-vibration-damper-for-3d-printer-nema17-stepper-motor-p-1310737.html?p=15141623958485201808 running low on filament get some here: https://www.banggood.com/anet-1kg-1_75mm-3d-printer-pla-filament-for-makerbot-mendel-printrbotreprap-prusa-p-992424.html?p=15141623958485201808 need more storage for all of those complex prints...
thingiverse
free
Helicoptrahedron Puzzle by RyanPuzzle
...zanden's curvy copter. this puzzle was printed on a printrbot simple metal in black pla, then sanded and polished....
thingiverse
free
Huge Cheap Home CNC (#hchcnc) by Enic
...threaded rod coupling) https://www.thingiverse.com/thing:1329750 thanks to lorenzo aspesi https://www.thingiverse.com/aspesilorenzo/about printrbot simple metal gt2 belt cliphttps://www.thingiverse.com/thing:746423 thanks to spanner hands...
Axis
3d_export
$99
MercedesBenz Axor Tractor Truck 2011 3D Model
...3d model 3dexport mercedes-benz axor 2644 tractor mercedes benz 3-axis 2011 2012 2013 2014 2015 2016 truck heavy duty...
3d_export
$99
Iveco Trakker Log Truck 4axis 2012 3D Model
...-axis 2011 2012 2013 2014 truck heavy duty trucks industrial
iveco trakker log truck 4axis 2012 3d model humster3d 59446 3dexport
3d_export
$99
MAN TGS Skip Loader Truck 2012 3D Model
...man tgs skip loader truck 2011 2012 2013 2014 2-axis heavy industrial trucks germany german man tgs skip loader...
3d_export
$50
Human Spine 3D Model
...human anatomy body medical cervical thoracic lumbar sacrum coccyx axis disc skeletal disk spinal column human spine 3d model...
3ddd
$1
Hulsta / Elea
...от hulsta / elea модель телефизора из сборника cg axis faces:...
3d_ocean
$7
3D Mirror
...design. this model ready to be machined using 3 axis ...
3d_export
$10
Wind Turbine 3D Model
...kinetic electrical aerofoil powered generator windmill farm hawt horizontal axis electric wind turbine 3d model download .c4d .max .obj...
3ddd
$1
Outdoor Gym Set 1
...point of each element is at zero on the axis "z". gym vol.7538 polys - 19986 verts - 20580...
cg_studio
$79
75mm Pak 97/383d model
...pak 97/383d model cgstudio 75mm anti anti-tank artillery at axis firearm german gun heavy ii military nazi pak tank...
3ddd
$1
LEGO SW Imperial Shuttle
...- all textures inside - rotation groups with true axis - 350k polys - 230x175x215 mm. - fbx +...
Y
3ddd
$1
Mexico Diabolo chair
...destino de playa favorito de actores y famosos de hollyood: acapulco, méxico. medidas generales 69cm x 69.5cm x 64...
3ddd
$1
Игровой автомат Gaminator fv629
...игровой автомат gaminator fv629. polys: 14 864 x: 570mm y 415mm z:...
3ddd
$1
Букет сирени
..., букет , ваза polys: 331007 габаритные размеры: x-545mm, y525mm, ...
3d_ocean
$59
FABRIC TEXTURES PACK 001
...use it for texturize cloth, characters or anything what y.. ...
3d_ocean
$59
FABRIC TEXTURES PACK 004
...use it for texturize cloth, characters or anything what y.. ...
3d_ocean
$59
FABRIC TEXTURES PACK 003
...use it for texturize cloth, characters or anything what y.. ...
3ddd
$1
Orchid bouquet 2.0
....obj overall dimensions of model: x = 450 mm y = 460mm z = 745 mm the archive contains...
3ddd
$1
DUNE - PAN DE ORO
...de oro que le darán a cualquier ambiente elegancia y sobriedad. es ideal para combinar con blancos, negros y...
3d_export
$6
Lucienne Monique Y 30 3D Model
... model lucienne 30
lucienne monique y 30 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl deckorator 104223 3dexport
3ddd
$1
Кровать Шато HRL0-LG, тумба прикроватная открытая Шато HRC1 и плитка 1900 от Vives Azulejos y Gres
.../mebel-provence/kollekciya-chateau.html
3.плитка
производитель:vives azulejos y gres
коллекция:1900
размеры:200х200мм
Simple
3d_export
$5
Simple wrought iron 3D Model
...simple wrought iron 3d model
3dexport
wrought iron architectural
simple wrought iron 3d model wfnv2000 65363 3dexport
3ddd
$1
Neverending Glory
...collection traverses the diversity of crystal chandeliers to a simple outline which symbolically creates a never-ending shape in its...
3ddd
$1
Lightstar / Simple Light
...lightstar / simple light
3ddd
lightstar
люстра simple light, lightstar (италия) . текстуры в комплекте, есть файл .obj
3ddd
$1
Bolt Down Snow Fence
...bolt down snow fence 3ddd снегозадержатель a simple snow fence model to add realism in your exterior...
3ddd
$1
table d'appoint design simple
...рнальный , круглый
table d'appoint design simple
couleur: noir
matière: bois laqué
3ddd
$1
Window for roofs
...as layered blend materials- they may render slower then simple vray...
3d_ocean
$9
Bed chalets
...chlet hotel nature solid wood wooden bed in a simple wooden chalet style. solid...
3d_ocean
$4
Drinking Glass
...kitchen soda softdrink table transparent tumbler water whiskey a simple drinking glass facecount: 491 (2x subsurfed:...
3d_ocean
$3
Low Poly Green Mushroom Hand Painted
...hallucinogenic lethal little low mushroom orc poison poly shaman simple small visions warhammer boost your game production with this...
3d_ocean
$4
Shave Streamers Celebration
...shader shave shave and a haircut streamer textured a simple hairfur preset file made for shave and a haircut...