Thingiverse
LED Bar for Voron v2.4 3D Printer by Ssendam13
by Thingiverse
Last crawled date: 3 years ago
Purpose and Suitability
This is a Rack and Rail system designed to hold an LED bar for a Voron v2.4 350 3D Printer, although it will happily work with other sizes of Voron v2.4 but you will need to amend the length of the Rail (Light_Bar_Holder.stl) accordingly. It should also work for other v2 Voron's.
Features
3 point positionng system; striaght down, 45 degrees and half way between.
Easy of access; just
Fitting and UseWARNING This design is all about the FITTINGS and not the ELECTRONICS. You will need to have knowledge of how LED lights strips work and how to connect them up safely. Don't be put off by that, let's face it if you've build your Voron and got it running then you should have the knowledge you need BUT this is my disclaimer.
I've fitted 3 LED bars in the top of the Voron 3D Printer, you could fit 4 but I didn't want a bar facing me as I looked at the printer front on. Each side gets 3 clips, left, right and centre. The LED_Frame_Clips.stl fits in first with an M3 roll-in t-spting nut and an M3 6mm SHCS holding it in place. It goes on the inside of the frame bar, and ake sure you get ip the right way up (it's quite obvious),
The LED_Light_Bar_Clip.stl just slides in from the top
You need 2 Light_Bar_Holder.stl prints per side. The middle clip acts as a joint to hold them together in the centre.
It is easy to put the bar in on the back rail and snap it up into place. You can use this method to change the setting but snapping it up to the other 2 holding positions. Have a play with this before fitting.
I won't lie, actually putting the electrics in is a bit fiddly. You have to connect up the electrics from bar to bar but if you keep the wires short then they sit nicely out of the way of the Z Pullies. I put the wires at the nack inside the frame and used black electrical tape to secure inside so it was nice and flat.
Make sure you know where this goes on the SKR board, and which board. You will need to alter your printer.cfg file. This is the same whenever you fit the LED's irrespective of the fittings you use.
Printed Parts List
Light_Bar_Holder.stl x 6
LED_Frame_Clip.stl x 9
LED_Light_Bar_Clip.stl x 9
Other Parts
M3 x 6mm SHCS x 9
M3 Roll-in T Spring Nuts x 9 (I've had some trouble with the T-nut style but the roll in ones seem ok)
LED Light strip, 10mm in width, Indoor, (24v is best for Voron)
LED Light Clips (to connect the strips)
Wire of an appropriate guage.
This is a Rack and Rail system designed to hold an LED bar for a Voron v2.4 350 3D Printer, although it will happily work with other sizes of Voron v2.4 but you will need to amend the length of the Rail (Light_Bar_Holder.stl) accordingly. It should also work for other v2 Voron's.
Features
3 point positionng system; striaght down, 45 degrees and half way between.
Easy of access; just
Fitting and UseWARNING This design is all about the FITTINGS and not the ELECTRONICS. You will need to have knowledge of how LED lights strips work and how to connect them up safely. Don't be put off by that, let's face it if you've build your Voron and got it running then you should have the knowledge you need BUT this is my disclaimer.
I've fitted 3 LED bars in the top of the Voron 3D Printer, you could fit 4 but I didn't want a bar facing me as I looked at the printer front on. Each side gets 3 clips, left, right and centre. The LED_Frame_Clips.stl fits in first with an M3 roll-in t-spting nut and an M3 6mm SHCS holding it in place. It goes on the inside of the frame bar, and ake sure you get ip the right way up (it's quite obvious),
The LED_Light_Bar_Clip.stl just slides in from the top
You need 2 Light_Bar_Holder.stl prints per side. The middle clip acts as a joint to hold them together in the centre.
It is easy to put the bar in on the back rail and snap it up into place. You can use this method to change the setting but snapping it up to the other 2 holding positions. Have a play with this before fitting.
I won't lie, actually putting the electrics in is a bit fiddly. You have to connect up the electrics from bar to bar but if you keep the wires short then they sit nicely out of the way of the Z Pullies. I put the wires at the nack inside the frame and used black electrical tape to secure inside so it was nice and flat.
Make sure you know where this goes on the SKR board, and which board. You will need to alter your printer.cfg file. This is the same whenever you fit the LED's irrespective of the fittings you use.
Printed Parts List
Light_Bar_Holder.stl x 6
LED_Frame_Clip.stl x 9
LED_Light_Bar_Clip.stl x 9
Other Parts
M3 x 6mm SHCS x 9
M3 Roll-in T Spring Nuts x 9 (I've had some trouble with the T-nut style but the roll in ones seem ok)
LED Light strip, 10mm in width, Indoor, (24v is best for Voron)
LED Light Clips (to connect the strips)
Wire of an appropriate guage.
Similar models
thingiverse
free
Led Strip Bar Clips by RPiGuy
...oaded another version that added some more clearance tolerances to fit the led strip in easier and made them 1mm instead of .5mm.
thingiverse
free
LED light bar for Voron V2.4 or V1.8 by rcfishhunt
...his. i simply used 2 hammer nuts for 2020 extrusion and 2 m5x6 screws to attach. thank you to nero3dp on youtube for the idea!!
thingiverse
free
Let strip bar for ender 3 by sergb39
...p bar for ender 3 by sergb39
thingiverse
a led strip for ender 3 printer.
need a 3m screws with t nut to attach it to the rails.
thingiverse
free
LED-Strip mount for Ender 3 by AsderKnaster
...r supply. you might want to include a switch to turn of the light if you don't need it.
feedback is very much appreciated :).
thingiverse
free
Strip LED holder for prusa i3 6mm alu frame by dazza22
...roll with sticky back .)
i got mine from hobbyking i think .
the bar will clip on the inside frame and help light up print area .
thingiverse
free
LED strip extrusion clip remixed with wire channel and deeper pocket by DynamiteLaser
...rip sits a little deeper since i was using some leds salvaged from a work light and the pcb was a tight fit in the original clip.
thingiverse
free
Light Plate for Kossel Mini printer - LED Strip lights by kmccon
...de the strip through.
9 leds sit just below the carriages when the nozzle is at z=0
the hole in the plate fits a kcd11-101 switch
thingiverse
free
CR-10 X-rail light bar with switch by Hpersson
...st connect to 12v output.
uploaded v2 as the glue would not stick when the led strip got hot.
also made tighter fit to the x-axis
thingiverse
free
Wire clip for thin wires and LED strips by WidescreenJohn
...it down all the way. it holds beautifully with 6 x 1/2" wood screws. (i'm not sure what the metric equivalent would be.)
thingiverse
free
LED Strip - 2020 Extrusion Clip by jgs2765
...hold a standard led strip snug and keeps the entire string taught and out of the way. takes 15 minutes to print one at 5% infill.
Voron
thingiverse
free
VORON Tag by froggy2288
...voron tag by froggy2288
thingiverse
tag for a voron 3d printer. mounts directly to 20mm aluminum extrusion.
thingiverse
free
3D Voronization of Hand by kriffe
...3d voronization of hand by kriffe
thingiverse
3d voronization of hand.
thingiverse
free
Tool Holder Voron by Struppiboy
...ngiverse
ein praktischer zangenhalter für den voron 2.4 am gehäuse.
a practical pliers holder for the voron 2.4 on the housing.
thingiverse
free
Stand Voron 2.4 by Struppiboy
...uppiboy
thingiverse
ich habe für den voron 2.4 füße für squash bälle konstruiert.
i constructed 2.4 squash balls for the voron.
thingiverse
free
Voron Gopro Mount by JacobMakes
...filming timelape videos of my voron, i changed up the design to better match the style of the voron, also made it easier to print
thingiverse
free
Voron Switchwire - Build Log by DarekNorway
...uild bog is regularly updated on hackaday:
https://hackaday.io/project/174810-voron-switchwire-3d-printer
voron switchwire frame
thingiverse
free
Voron 2.4, Orbiter1.5 Mount by madsgadeberg
...extruder mount for the voron afterburner.
print settings same as other voron parts.
bolts: 4pcs m3x20 and regular m3 heat inserts
thingiverse
free
Voron 2.4 feet by maciek13
...voron 2.4 feet by maciek13
thingiverse
.
thingiverse
free
VORON case for Viki2 LCD by fulg
...on case for viki2 lcd by fulg
thingiverse
here is a case for the viki2 lcd. it is styled to match the rest of the voron printer.
thingiverse
free
Voron M4 Guidler with ID by falcon14141
...voron m4 guidler with id by falcon14141
thingiverse
simple remix of the voron m4 guidler to add identification of your extruder.
V2
3d_export
free
Lamp v2
...lamp v2
3dexport
lamp v2 with solar panel
3d_export
$5
hammerhead v2
...hammerhead v2
3dexport
razer hammerhead v2 headphones, modeled in cinema 4d, render in corona
3d_export
$5
manometer v2
...manometer v2
3dexport
3d_export
$5
potato v2
...potato v2
3dexport
turbosquid
$52
Lifebuoys v2
...squid
royalty free 3d model lifebuoys v2 for download as fbx on turbosquid: 3d models for games, architecture, videos. (1560870)
turbosquid
$2
Mask v2
...turbosquid
royalty free 3d model mask v2 for download as stl on turbosquid: 3d models for games, architecture, videos. (1527741)
turbosquid
$20
kengkod64-v2
... free 3d model kengkod64-v2 for download as 3dm, ztl, and stl on turbosquid: 3d models for games, architecture, videos. (1701415)
turbosquid
$20
Kitchen V2
...ty free 3d model kitchen v2 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1155111)
turbosquid
$19
Chair v2
...yalty free 3d model chair v2 for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1693360)
turbosquid
$15
Table v2
...yalty free 3d model table v2 for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1688743)
Led
3d_export
$5
led
...led
3dexport
the led is cut with all the parts.
3ddd
$1
Monacor / PARL56DMX / LED-320RGBW / LED-345RGBW / LED-300RGB
... прожектор
http://www.monacor.dk/
parl56dmx
led-320rgbw
led-345rgbw
led-300rgb
turbosquid
$10
LED
...led
turbosquid
free 3d model led for download as blend on turbosquid: 3d models for games, architecture, videos. (1691856)
3d_export
$5
led lamp
...led lamp
3dexport
led lamp, brightness animation
3ddd
free
leds-c4
...leds-c4
3ddd
leds-c4
современный торшер
3ddd
free
leds-c4
...leds-c4
3ddd
leds-c4
настольный лампа
turbosquid
$19
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Led
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Bar
archibase_planet
free
Bar
...bar
archibase planet
bar bar rack
bar 2 - 3d model for interior 3d visualization.
archibase_planet
free
Bars
...bars
archibase planet
horizontal bar parallel bars
parallel bars - 3d model for interior 3d visualization.
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
Printer
archibase_planet
free
Printer
...inter
archibase planet
printer laser printer pc equipment
printer n120614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Printer
...rchibase planet
laser printer office equipment computer equipment
printer - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$100
Printer
...er
turbosquid
royalty free 3d model printer for download as on turbosquid: 3d models for games, architecture, videos. (1487819)
turbosquid
$1
printer
...turbosquid
royalty free 3d model printer for download as max on turbosquid: 3d models for games, architecture, videos. (1595546)
turbosquid
$1
printer
...turbosquid
royalty free 3d model printer for download as max on turbosquid: 3d models for games, architecture, videos. (1595105)
turbosquid
$7
Printer
...royalty free 3d model printer for download as ma, ma, and obj on turbosquid: 3d models for games, architecture, videos. (1644580)
turbosquid
$30
Printer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Printer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$18
printer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$6
printer
... 3d model printer for download as 3ds, max, dxf, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1276861)
4
3d_export
$5
doors- 4
...doors- 4
3dexport
doors 4
3d_export
$5
hinge 4
...hinge 4
3dexport
hinge 4
3ddd
$1
Штора №4
...штора №4
3ddd
штора №4
3d_export
free
playstation 4
...playstation 4
3dexport
playstation 4
3ddd
$1
nexus 4
...nexus 4
3ddd
lg , телефон
nexus 4
3ddd
$1
4 Poufs
...4 poufs
3ddd
пуф
4 soft poufs
turbosquid
$12
Calligraphic Digit 4 Number 4
...hic digit 4 number 4 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389332)
3ddd
$1
Dauphin 4+
...dauphin 4+
3ddd
кресло
dauphin 4+ конференц кресло
3ddd
$1
iPhone 4
...
3ddd
apple , iphone , телефон
модель iphone 4.
3ddd
$1
4 игрушки
...4 игрушки
3ddd
4 текстильные игрушечки. материалы настроены. текстуры в комплекте