Thingiverse
3D Printing bed brace
by Thingiverse
Last crawled date: 4 years, 2 months ago
I was having trouble with tall prints coming detached from the print bed so I designed this magnetic 3d printing bed brace.
It allows for four 8mm x 3mm magnets to be attached to the bottom of the brace, which in turn hold the brace firmly to my metal PRUSA print bed.
Braces can be used in pairs, or more if needed, to hold the print object in place.
Here are two in action: https://youtu.be/Ul_DoyXgdg4
I use Octoprint to print the object to a point where it is high enough that I can pause the print, raise the extruder, carefully align the braces, lower the extruder, and resume the print.
The magnetic feet are offset a bit from the bottom of the brace such that the bottom of the brace doesn't touch the print bed - only the magnets touch the print bed.
There is also a small overhang which allows the brace to clamp over the print brim (if one exists).
You can get a package of magnets from Amazon here: https://amzn.to/2rfYtgS or elsewhere.
The magnets fit into the holes at the bottom brace, I used some Gorilla glue to help hold them in place.
One last tip: magnets have a north and south pole. When putting the magnets in place make sure all are facing with the same pole outward. It does not matter which pole faces outward, just that they all face in the same direction. The reason this is done is that if you always follow this practice and print two or more of the braces, when the braces are not in use, they can be stored together with one brace attracting and attaching (effectively snapping onto) to the next brace perfectly.
It allows for four 8mm x 3mm magnets to be attached to the bottom of the brace, which in turn hold the brace firmly to my metal PRUSA print bed.
Braces can be used in pairs, or more if needed, to hold the print object in place.
Here are two in action: https://youtu.be/Ul_DoyXgdg4
I use Octoprint to print the object to a point where it is high enough that I can pause the print, raise the extruder, carefully align the braces, lower the extruder, and resume the print.
The magnetic feet are offset a bit from the bottom of the brace such that the bottom of the brace doesn't touch the print bed - only the magnets touch the print bed.
There is also a small overhang which allows the brace to clamp over the print brim (if one exists).
You can get a package of magnets from Amazon here: https://amzn.to/2rfYtgS or elsewhere.
The magnets fit into the holes at the bottom brace, I used some Gorilla glue to help hold them in place.
One last tip: magnets have a north and south pole. When putting the magnets in place make sure all are facing with the same pole outward. It does not matter which pole faces outward, just that they all face in the same direction. The reason this is done is that if you always follow this practice and print two or more of the braces, when the braces are not in use, they can be stored together with one brace attracting and attaching (effectively snapping onto) to the next brace perfectly.
Similar models
thingiverse
free
UP BOX Extruder Mounting Plate - Magnet Removal by ATPerformance
...atsink.
you can now slide the extruder off and on by pulling it forward, no need to un-bolt.
i hope this is helpful for someone.
thingiverse
free
QIDI Tech I dual extruder leveling Jig by Pascal32
...e of the jig, put the straight edge against the side of the extruders to line them up, and tighten the set screws.
re-assemble :)
thingiverse
free
Pegboard Doweled Magnet by ogrda
....
i use these magnets: https://www.amazon.de/gp/product/b07sjznz3n
and this pegboard: https://www.amazon.de/gp/product/b0897xxvrp
thingiverse
free
Filament Filter and Wire Holder for Creality CR-10 by djf123
... is a two piece assembly. i used supports to hold up bracket1.stl. i don't know if this piece can be printed without supports
thingiverse
free
Magnetic holders for Solidoodle2 glass bed by rincewind
...ached to iron like in http://www.soliforum.com/topic/814/magnetic-glass-bed-mounting/ . credits go to cmetzel for the inspiration
thingiverse
free
Magnetic Rhombic Dodecahedron Blocks by DaveMakesStuff
...ocess, magnet to magnet, until all the holes are filled.
the magnets can be press fit into the hole with pliers, no glue needed..
thingiverse
free
Table Leg Brace by Boscoe
...an be screwed into the bottom table and will hold the leg of the upper table in place. put one at each corner of the lower table.
thingiverse
free
Simple Glass Bed Mount by EstSom
...ttached.
(if you decide to print them and use them, please upload a photo and give me some feedback!! i'll be very thankful)
thingiverse
free
Magnetic puzzle box geocache by gmarsh23
...al surface, to keep the magnets in place at the bottom of the holes when the glue dries.
openscad design file is attached. enjoy!
thingiverse
free
UP BOX Extruder Mounting Plate - Magnet Removal by ATPerformance
... installing the bolt.
you can now remove the extruder by pulling it forward out of the magnet mount, no need to unbolt everytime.
Brace
thingiverse
free
Wrist brace
...wrist brace
thingiverse
wrist brace
thingiverse
free
Brace by PearceCrocker19
...brace by pearcecrocker19
thingiverse
leg brace
thingiverse
free
brace by joestraws
...brace by joestraws
thingiverse
brace prototype
thingiverse
free
Brace
...brace
thingiverse
watch spies in disguise online
thingiverse
free
Brace
...brace
thingiverse
download frozen ii full movie
thingiverse
free
catwalk brace by NYC3D
...catwalk brace by nyc3d
thingiverse
catwalk brace
thingiverse
free
Pistol Brace
...pistol brace
thingiverse
pistol brace for commercial m4 buffer tubes
uses one bolt and lock nut to mount
thingiverse
free
Ivar Brace by alotto
...ivar brace by alotto
thingiverse
wip brace for kitten
thingiverse
free
Braces for teeth by WillandMrData2
...braces for teeth by willandmrdata2
thingiverse
braces to straighten teeth,
thingiverse
free
Camera Brace by aladisposition
...camera brace by aladisposition
thingiverse
a camera brace test. hope it works!
Bed
thingiverse
free
bed by
...bed by
thingiverse
pink bed with a white pillow
thingiverse
free
Kossel Plus bed holder for aluminium bed with glass bed
...kossel plus bed holder for aluminium bed with glass bed
thingiverse
pla
thingiverse
free
bed by Syzguru11
...bed by syzguru11
thingiverse
bed
thingiverse
free
bed by callsaul
...bed by callsaul
thingiverse
bed
thingiverse
free
BED by leonk
...bed by leonk
thingiverse
bed
thingiverse
free
Bed by FaserMok
...bed by fasermok
thingiverse
bed
thingiverse
free
Bed by alexdfox
...bed by alexdfox
thingiverse
bed maker
thingiverse
free
bed stanchion
...bed stanchion
thingiverse
top of a bed stanchion
thingiverse
free
bed by bhawkinscds
...bed by bhawkinscds
thingiverse
four post bed
thingiverse
free
bed by EricG
...bed by ericg
thingiverse
bed by eric [created on 3dtin]
Printing
thingiverse
free
for print by Kieran20
...for print by kieran20 thingiverse for printing ...
thingiverse
free
Test Print - Calibration Print by fischer99
...nt settings. includes bridge, overhang, square walls and round walls.
i print with 20% infill, 3 shells, skirt only, no support.
thingiverse
free
Printing by munchanc
...printing by munchanc
thingiverse
things to print
thingiverse
free
Test Print
...test print thingiverse much fun by printing ...
thingiverse
free
Print test
...print test
thingiverse
i use it to test print parameters for new materials
thingiverse
free
PRINTED by t_kondo
...printed by t_kondo thingiverse it's just a 3d printing typeface...
thingiverse
free
3D Printed ball (Print Your own) by 001002003004
...3004
thingiverse
print your own ball
steps
download the size you want to print
double click on the file
click print
thingiverse
free
3d Printing Support Test Print
...can learn more about using supports in cura on the drvax youtube channel and by watching this video:
https://youtu.be/qko_ayibp8k
thingiverse
free
Print on Fabric - small test print by OeG3D
...ingiverse
we tried to print on fabric as shown in https://www.thingiverse.com/thing:2787803
use the link above for instructions.
thingiverse
free
Print Scoop by Gibson1990
...print scoop by gibson1990
thingiverse
scoop for lifting 3d prints off the print bed