Similar models
grabcad
free
鼠标壳固定定位架
...鼠标壳固定定位架
grabcad
鼠标壳固定定位架
thingiverse
free
Cetus 3D printer handle by dlchang
...4螺絲固定在料架上,高度調整到線材不會卡到下方的鋁擠。
3.將「rack_handle_料架提把.stl」由鋁擠上方推入到底,鎖上m3的螺絲固定住。
4.放入線材後,可加裝「filament_cap-耗材擋片.stl 」防止在提著料架或列印時,線材掉下來。
thingiverse
free
12864屏幕固定架 by nerfg
...12864屏幕固定架 by nerfg
thingiverse
12864屏幕固定架配合https://www.thingiverse.com/thing:2319753 模型使用
3dwarehouse
free
玻璃架子固定件01
...玻璃架子固定件01
3dwarehouse
倒角
thingiverse
free
Fast deduction by czl
....快拆轉軸:橫向放入鋁擠溝槽,順時針旋轉固定,固定板厚度設定為2mm,這一點需注意,不然無法裝置.
2.小蟻攝影機固定架:以atom2.5ex為設計方向,剛好可與列印平台平行垂直,做遠端監控使用,組裝僅需把原本底座拆除,使用原本螺母與螺絲鎖上去此固定架即可.
3dwarehouse
free
洗腎中心濾水器
...洗腎中心濾水器
3dwarehouse
濾水器固定架
3dwarehouse
free
pv支架
...pv支架
3dwarehouse
水平支架,包括基板、固定用螺栓和梁柱 #198274
3dwarehouse
free
固定環
...固定環
3dwarehouse
固定環 #固定環 #避難器具
grabcad
free
把手
...把手
grabcad
把手
3dwarehouse
free
把手
...把手
3dwarehouse
门把手
把手固定架
thingiverse
free
PlaRail pier for elevated rail 高架レール用橋脚 by hjfuji
...ブロック橋脚と比較して、高架レールとの一体感が高いです。
top.stl/top2.stlの出力結果に、leg.stlの出力結果を接着します。
具体的な利用手順はyoutubeの動画を参照してください。https://youtu.be/m6fzpjos6bw
thingiverse
free
Phrozen Sonic mini 4K 滴料架 by msehjc
...en sonic mini 4k 滴料架 by msehjc
thingiverse
just my design of a insta360 go camera mount for the diatone tinawhoop. super simple.
thingiverse
free
iPad(or tablet) holder with flexible flap (wall or bottom mount) by hrdworld
...マウント版も作ったので用途に合わせて選んでください。
側面を下にすることで、サポート無しでプリントできます。
壁厚みを調整して、真ん中のバネ部分が100%中実になっているようにしてください。
両バージョンともに4mmのネジ2本で固定することを想定しています。
thingiverse
free
Oculus Quest 2 Controller Wall Mount with Stapler or Screws by CyberCyclist
...ないものが結構多い)。
m4ねじを使うバージョンもアップロードしてます。ただし穴をあけられる壁が手近にないので未テストです。
quest2本体(ゴーグル)の壁マウントはこちら。https://www.thingiverse.com/thing:4631020
thingiverse
free
Fletching (FOB) Archery by lidaiyang
...e stable in theory.
because the fob-3 and - 4 are too close to the shaft, we have to use special tools, which is very convenient.
thingiverse
free
Pet Bottle Cutter by ichibey
...pet bottle cutter by ichibey
thingiverse
ペットボトルカッターです
sサイズのカッター替え刃の4コマ分を内部に固定して使用します。
ガイド部固定にm3ナット及びm3x10lネジ2セットを使用します。
thingiverse
free
Anakin's LightSaber Skin for DIY Lightsaber (31mm Diameter) by gumo_design
...孔,用ping270列印出來組裝。
金屬光澤就比較難了,最後也只能用汽車冷烤漆的銀色來噴塗(最好不要用一般噴罐的銀色,它們通常用手摸沒幾下就會霧掉)
雖然是列印件,但它只算是皮膚,中間還是有原本的臥雲鋁合金握把,因此把玩是不會斷掉的,就算是摔到也不會太心疼。
thingiverse
free
Oculus Quest 2 Goggles Wall Mount with Stapler or Screws by CyberCyclist
...ないものが結構多い)。
m4ねじを使うバージョンもアップロードしてます。ただし穴をあけられる壁が手近にないので未テストです。
quest2コントローラ用の壁マウントはこちら →https://www.thingiverse.com/thing:4625235
thingiverse
free
[3D升級]腳墊抗震球架 ball feet Anycubic I3 MEGA by DVPBear
...c frame.
i am satisfied.
i think it's pretty cute.
this is the foot pad for m5 thread.
m5 screw should change to 20mm length.
thingiverse
free
Nerf XX-700 FinisherMod Kit by Leeloo1991
...//www.thingiverse.com/thing:4483129
releaselever original author:https://www.thingiverse.com/thing:4483129
感谢兔团cheng在制作过程中给与的建议。