thingiverse

free

DC Power Plug Connector Jack Screw Terminal Wire Clamp Protector / Strain Relief

...ck recommended). make sure to pull the zip tie tightly! there's a groove in the male/female part so it doesn't stick out.

thingiverse

free

ZHIYU DC 2 Way Cooling PWN 4 wire Fan Temp. Controller by Jsquires90

...ted insert the buttons and the. the small m piece into the side of the buttons, i dabbed a little glue to the top of the m piece.

thingiverse

free

Drill bits holder for DIY press drill with mounting holes for DC jack, main switch and wire protector by mariocaptain

...c jack of 8mm in diameter), a main switch (rectangle type, mounting hole is 12x20mm) and a 10mm hole for a rubber cord protector.

thingiverse

free

300W XL4016 DC-DC Case by ua6ahp

...300w xl4016 dc-dc case by ua6ahp thingiverse 300w xl4016 dc-dc case. the model has a channel for better wire fixation.

thingiverse

free

Wire stress reliever by Fuintur

...wire stress reliever by fuintur thingiverse wire stress reliever for ac/dc converter

thingiverse

free

DC-DC Stepdown Module Case & Lid (XL4015) by Couch_Mango

... (xl4015) by couch_mango thingiverse a simple case for the xl4015 dc-dc stepdown module. holes included for wires if applicable.

thingiverse

free

TETRIX Motor wiring guide by hexafraction

...tetrix motor wiring guide by hexafraction thingiverse a holder and wiring guide for a tetrix dc motor controller.

thingiverse

free

Wire Holder by babaNmama

...wire holder by babanmama thingiverse wire holder for dc 5.5 x 2.1 or 2.5 mm plug using

thingiverse

free

holder for DC power connector 2.1mm by Jika

...holder for dc power connector 2.1mm by jika thingiverse little tool for fixing connector and wire together.

thingiverse

free

DC-DC enclosure

...3a step down power supply module voltage buck converter adjustable" example:https://www.aliexpress.com/item/32826540392.html

thingiverse

free

Sparkfun DC DC Convertor Box + Lid by MorkFromOrk

...70) once printed, the pc board fits nicely in place. seperate holes are foreseen for the wires. source files included. have fun !

thingiverse

free

DIY Power Supply DPS5005 by RianB

...converter. one of the other 2 wires should be wired to one of the poles of the switch, and...

thingiverse

free

XL4015 XL6009 buck/boost box by ffejrxx

...c xl4015 buck or xl6009 boost boards screw hole on bottom, wire exits on ends side clips to hold boards slip together holds tight

thingiverse

free

Portable 1S 4x Lipo Charger with LED-Voltage-Display by porty

...intet buttons to the dc-dc buttons if you want. the buttons are only for the led display (in-voltage / out-voltage / display off)

thingiverse

free

Console for SK35 / XYS3580 DC DC converter by fjkraan

...laptop adapter. the current console design is only for light electric use; ~5 watts, as there is no real fan duct (xys3580 only).

thingiverse

free

MT3608 DC-DC Voltage Adjustable Boost Converter

...here is leaves very little wiggle room. the boost voltage should be set before the case is finally sealed with a few dabs of pva.

thingiverse

free

DC Cord Extender - Universal spool 90mmDiam by Artean

...sing spare spools to wind the wire before twist. included false lever to rewind if you don't need have actually banana plugs.

thingiverse

free

Sega GameGear Ext Power Mod! by RCConcepts

...le pot) a pair of 5cm-insulated 22awg copper wires (red and black) a dc female jack for standard 12v dc adapter plug (with wires)

thingiverse

free

Ryobi Battery to DC-DC Converter with 12V Acc Port by supyo

...24v -> 12v (amazon) generic 12v accessory port battery terminals (digikey part: 36-204-nd) various wires and screws and a fuse

thingiverse

free

16 Slot Rotary Magnetic Bow

...ontroller, it can be used to induce vibrations into ferrous wires to make music. demonstration here: https://youtu.be/tuehd1pam6m

thingiverse

free

Versatile Power Supply Cover/Enclosure

...and xt60 connector. the ac power socket should be wired according to these instructions. (https://www.instructables.com/id/wire-up-a-fused-ac-male-power-socket/) insert the three sockets...

thingiverse

free

Case for DC-DC Converter Adjustable Step-Down Module by McDoS

...t; in bottom part. if you do not need any symbols on top cover - use "top_clean.stl". (rotate top cover to 180 degrees)

thingiverse

free

Power Supply Front End - Alt Lab Supply by MCmaks

...f-tap into the body. 9) optional: apply small adhesive rubber feet (4x). https://youtu.be/syrfwwdw3rwhttps://youtu.be/0hl5d5ysglq

thingiverse

free

DC 5.5 Plug body by Shadow8286

... thread. fusion360 project attached so you can customize thing as you want. use a piece of shrink tube to protect wire near plug.

thingiverse

free

DC Motor Speed control Box for ericthepoolboy engines by Dblnaknak

...also purchased a 120v to 12v converter plug and wired it into the contorller so i would not need...

thingiverse

free

3D Water Pump by bygreenthumb

...casing. remember to slide the battery clip wires through the holes of the top of the water pump before soldering the ends to the

thingiverse

free

Fan for soldering from old 2.5inch harddisk by kapik1

....html?akmclientcountry=it&utm_campaign=12686806_1192297&utm_content=11209&p=3y290412686806201707&cur_warehouse=cn

thingiverse

free

adjustable multi voltage power box for the stacker and trommel by caj

...to 12v switch and the other side to +12v lead out solder the other 2 out plugs directly to the buck dc-dc converter -out and +out

thingiverse

free

Piaggio Fly headlight LED support by lari6

...urrent wire from your scooter. you will have to drill a hole in order to fix the led to this support in the position you want to.

thingiverse

free

Spool by DimonSmart

...ith hole for easy wire fixing and a smoller drive shaft. my drive shaft size is 2.9 mm x 4.9 mm and drive model is 28byj-48 5v dc

thingiverse

free

Spider Robot wide body for Nano expansion board by sb43201

...the servos, an additional dc-dc converter is used and wired to the 5v bus on the expansion board to...

thingiverse

free

Dual Power Supply Front End - alt lab supply by MCmaks

...-tap into the body. 10) optional: apply small adhesive rubber feet (4x). https://youtu.be/i5zasdwc5l0https://youtu.be/0hl5d5ysglq

thingiverse

free

DC Power Jack Housing

...ter soldering the wires onto the dc power jack barrel, slide it into the housing and feed the cable through the hole on the side.

thingiverse

free

Case for RD DPS5005 DC-DC step down module (laboratory mini power supply) by Egorich

...l4a57bw 4) banana plugs couple terminal: https://www.amazon.com/highrock-terminal-binding-amplifier-copper/dp/b00d6aicr4 5) wires

thingiverse

free

LP-E8 Battery for Canon 600d by MarcinWojcik

...dc/dc ) 10v 1a (or more) charger (ac/dc) soldering iron some wires printing parts patience simply circuit https://ibb.co/jqwcrjc

thingiverse

free

Banana to DC jack adapter by TimotheFrignac

...fit in). material needed : banana plug (x2) dc jack 1 m3 nut 1 10mm m3 screw some wire tools (knife, dremel, soldering iron, ...)

thingiverse

free

Passthrough battery LP-E12 (Canon SX70hs) by olegr1

... space for that. my design does not have a dc-dc converter. printing: no supports, make sure that the flat section is on the bed.

thingiverse

free

cc2531 router boxes by Droscy

...c wires for 5v output (general purpose dupont wires are ok) usb female connector type a (or you can solder wires on cc2531 board)

thingiverse

free

Microcube RAMPS DC barrel jack holder for power in by ort

...arrel jack screw the barrel jack in the support plug and screw the wire into the ramps terminals fix the support with two zip tie

thingiverse

free

Base Socket Tealight 12V AC/DC by ddchesser

...crew in the connector solder the led to the wires und press the led in the base you don't have to take care for the polarity.

thingiverse

free

TS100 DC Voltage Booster 150W with Voltage Display by Ajaxdima

...to take inplace the display and heatstrink for insulation vire this is a remix of this: https://www.thingiverse.com/thing:1484476

thingiverse

free

CR-10 LED light bar by thatdude902

...ted with m4 screw + t-nut or just 3m tape. the opening for the switch is 12.3mm x 20mm, and the opening for the dc jack is 8mm.

thingiverse

free

Home made motor by EB7571

...mounter to a stationary object. the holes are to wrap coils of wire into to create the electromagnetic field that runs the motor.

thingiverse

free

Roaming Robot by lynce9956

...5v dc 4-phase 5-wire + uln2003 driver board range finder: hc-sr04 microcontroller: arduino uno https://youtu.be/n5mby3c59hc

thingiverse

free

Remixed Left Case by pigaro

...and difficult for the relay connector to clamp. i wired the dc-dc converter directly to one set of unused...

thingiverse

free

4 Port USB 12v Buck DC-DC enclosure by eqnish

...converter to add power ports to my printer, i wired to a available 12v leg on the printer power...

thingiverse

free

Fan cooler notebook by 3dworkscl

...luminium has less weight and is cheap -fan 80mm 12volt -step-up converter dc-dc 5v to 12v (ebay link) -usb wire. -screws for fan.

thingiverse

free

Case for DP30V5A-L DC-DC converter; XT60 input & output by JonasCz

...an for the other side. if you don't need more than 1-2 amps, it should be ok without the fan. print the pieces on their side.

thingiverse

free

Arduino Nano Case + Cover by nitbeat

... completely but it's possible to design a cover that will allow opening for passing wires when in beta testing stage. nitzan.

thingiverse

free

DC Coupler DR-DC10 (Battery To DC Canon SX 160 IS) by trustfm

...e a small wire and use solder. you should use a dc 3v 1a power supply i do not have any responsibility if you damage your camera

thingiverse

free

Case for Makerhawk USB DC-DC Buck Regulator by adammelancon

...ltage board 3a 6-26v car charge charging regulator (4pcs) https://www.amazon.com/dp/b07kwrh61d/ref=cm_sw_r_cp_api_i_zfbxfb4dwm8jp

thingiverse

free

$10 DIY Variable DC Bench Power Supply by tman67234

...is amp control, as seen here. the display is wired like this, except that i powered the display on...

thingiverse

free

Variable power supply by Giammy_hsq_99

...ring in the back cover, there is a housing for two plastic clamps which have the task of keeping the wires firm in case of draft.

thingiverse

free

DPS5005 Case by Arbaal

...m3 iso4762 screws (m3x15 should work fine) m3 suqare nuts (din562) designed in fusion360. fusion 360 archive project is attached.

thingiverse

free

Bluetooth Module Housing for Bose Soundock Series 1 by grp1964

...a bose sounddock series i, and the module is wired to the docking circuit board on the module to...

thingiverse

free

DC-3 / C-47 Landing gear retract by 3SO

...ifications to a previous design by benglish. hardware needed : 2 mm steel wire 5 mm carbon rod 6mm carbon rod superglue + kicker

thingiverse

free

AMB Mylabs Transponder Charger by HenrikA

...e new and old style amb tranx 160 transponder. use 2 small pieces of brass, 2 wires and a 2.1mm dc socket and you are good to go.

thingiverse

free

Shapeoko 3 Y Proximity Homing/Limit Switch

...c1-5mm-3-wire-inductive-proximity-sensor-detection-switch-npn-dc-6-36v-yt (wire connection brown 5v / black signal / blue ground)

thingiverse

free

FPV receiver by Cichaczech

...er video signal and power supply to lcd logic board. isolate all electronic parts ( i used kapton tape). now put it all together.

thingiverse

free

MiniBox for mini 360 DC/DC buck down converter by anhtien

...d-stop. printed using 50mms speed, 50% infill, 200deg extruder, 60 deg hotbed using pla 1.75mm, support generation needed. enjoy.

thingiverse

free

BLDC Permanent magnet

...rushless permanent magnet 3 phase motor dc powered. wiring configuration designed in solidworks. working on releasing .scad files

thingiverse

free

DC PWM Throttle Box

...extended the wires to keep the throttle and the main controller box separate. i use this on my pedal boat mounted trolling motor.

thingiverse

free

12.6V battery pack 6x18650 by BambaVeCola

...male deans connector 1x 5.5mm x 2.1mm male dc power plug 1x 5.5mm x 2.1mm female dc power plug 1x xt60 plug 1x car 12v socket

thingiverse

free

Parkside X20V battery adapter - Mini Power Supply

...original adapter battery rail print settings printer: anet a8 supports: not required resolution: 0.2 0.32 for the lid infill: 20

thingiverse

free

Lamp by MABC

...wright, with all straight lines. it uses three led's wired to an rgb controller, i also used a 12v...

thingiverse

free

Model stepper 28BYJ-48 by siderits

...r with uln2003 driver board (without driver board. used in modeling enclosures. included an indicator for this stepper motor.

thingiverse

free

Baby Mobile Motor Unit by lundiplutzmus

...is is an electric device and the battery clip with loose wire is a dirty hack. use at own risk and never let this run unattended!

thingiverse

free

Arduino Uno + Buck converter Case by ERDesigns

...temprature and everything else i will add in the future :) there are holes for easy acces for the wires (temp, leds, screen etc).

thingiverse

free

E3D v6 Bowden head for prusa i3 40mm Fan and 18mm Sensor by David_L_G

...r-switch-npn-dc-no-300ma-/121864216190?hash=item1c5fac5e7e:g:29yaaoswffhxjoeo the files i used to print the head on the photo are

thingiverse

free

Arlo AC to DC adapter by BlackGT360

...and with the following parts you can make it wired (you will not use batteries anymore) required parts. 4...

thingiverse

free

battery case for 12 volt aquarium backup power supply by rickcavanaugh

...e you 12-24 hours of runtime on a pump running on low speed or a propeller powerhead. this will only work on a 12v dc drive pump.

thingiverse

free

Housing for the W1209 DC 12 thermal relay with aliexpress.

...f of your device at the temperature you set.https://aliexpress.ru/item/32991123098.html?spm=a2g0o.detail.1000023.7.5be91702s48dbn

thingiverse

free

DIN rail mount for PowerPole connectors: upright by ecloud

...owerpoles instead of wiring directly. you can screw a short m3 bolt into the bottom to hold it more tightly in place on the rail.

thingiverse

free

Mobile photography fill light by jackyhoy

...e. 3.3 series lithium battery protection module 4.dc-dc boost constant current module battery indicator module switches and wires

thingiverse

free

voltage control and measure box - speed controller by wingmaster

...the multiturn potmeter in. the toggle switch can be wired in the output to disable the output. the dcdc...

thingiverse

free

Proximity Switch holder for a REK hot end by BobDavis73

...sor wires and connect it to the npn proximities third wire. this allows the sensor to work without any resistors in the circuit.

thingiverse

free

Power monitor case for Anet A6 by jbanion

... why not tip me a dollar or two. your support will allow me to spend more time on these designs and their variations. thanks!

thingiverse

free

DC2416 AC/DC inverter Box by anhtien

...t to screw the wires in, maybe 9 or 10 is better. but it worked out for me so i won't reprint or change my scad file. enjoy.

thingiverse

free

Led Light handle

...factor for pla you need: led line power block (220 dc -> 12ac transformator) aluminum rail (250(or any lendth)x 15x 2)mm wires

thingiverse

free

IBT 2 DC Motor Controller Enclosure by KhalidKhattak

...out support and just assemble as seen in the picture. the 4 holes to be tapped 3mm and use 4 m3 screws to tighten with ibt2 base

thingiverse

free

Power supply with adjustable voltage by MDavid12

...socket female panel mount connector 5.5mm x 2.1mm -voltage display dc meter 3-digital mini voltmeter wires led 0-30v panel tester

thingiverse

free

Yu-gi-oh duel disk Arduino life counter by gaeran

...micro compatible x 1 red led x 2 li-po battery x 1 dc-dc step up (3.7v to 5v) circuit. lipo battery charger circuit. and wires...

thingiverse

free

small drill case by madbrain

...u will need: 555 metal gear motor with drill chuck rectangular switch 13x19mm dc in line plug socket female 8mm electrical wires

thingiverse

free

OrangePI PC case with smart ventilation by axill

...e controller based on mcu is used to provide smart cooling depending on temperature. hex for stm8s003f3 is available upon request

thingiverse

free

7" Touchscreen with Keyboard Rugged Raspberry Pi Tablet by morganlowe

...type a cable wiring: starting with the batteries i wired them each with a length of 20ga silicone wire...

thingiverse

free

Vacuum Cleaner by markica

...) 3a 12 v motor button wires screws when printing container use brim. https://youtu.be/bf4jt5-ldb8 https://youtu.be/noalusivbwe

thingiverse

free

Cover for 0.36" LED voltmeter by Fireflynj

...o use sticky back tape to mount on flat surface. https://www.amazon.com/bayite-digital-voltmeter-display-motorcycle/dp/b00yaluxh0

thingiverse

free

Wireless DMX module XLR enclosure by bipsen

...ture update 2018-02-07: improved body, lid and endcap added as version 2.1. xlr-ring and and xlr-plug parts are still the same.

thingiverse

free

Dji Phantom Inspire DIY car 12v charger case by omegas

... i'm found in this video https://youtu.be/czokljvvxze - you can find here all instructions, wire connection and setup manual.

thingiverse

free

Shelf Mount for Cheap DC/DC Power Supply by cw360

...put a command velcro strip between the front of the shelf and the enclosure to prevent it from moving around if wires are tugged.

thingiverse

free

Adjustable Power Supply 0-32V - 5A by kain90

...0 silicon wire 22awghttps://www.banggood.com/it/1m-8101214161820222426-awg-silicone-wire-sr-wire-p-921159.html m2 x 6mm screws

thingiverse

free

Dual 18650 charger by RGN01

...4057-lithium-battery-1-a-led-charging-board-reverse-connect-protect/32368102064.html and the dc socket is ebay item 321179995395.

thingiverse

free

DIY Printer Extruder Fan Prusa I3 Copy Reprap CTC by Fugazi123

...eprap diy copy, whatever it is :) wire a 12v 5mm led into the fan ( if its dc ) to see your workspace better. seems to work well!

thingiverse

free

Wyze Cam Mount for M&S DS3 Intercom Door Station

...12v dc power supply behind the intercom control panel, wired the existing speaker wires to it, added a 5v...

thingiverse

free

Test Box by dacoop1988

..., an effect send and an effect return wire out the little holes on the top to plug into the appropriate spots on your breadboard.

thingiverse

free

High voltage from CR Battery pile by apspurgeon

...s together. holes in the end for the +/- wires, and recommend using a plate against the battery ends (rather than the screw end).

thingiverse

free

Revan's Lightsaber mountable by tblkbandec

...odel for a star wars cosplay. i use a 9v battery, some wires, switch button, 12v plug from dc adapter, 25mm pipe, led strip light

thingiverse

free

Arduino handheld arcade cabinet by Mehozavr

...uzzers power switch 3 aa battery holder 50*70 solder board 6x 12*12 tact buttons with caps m3 and m2 screws wires and other stuff

thingiverse

free

DIY Rework hot air station by Scrachi

... wiring explanation soon... <= if you like my work, you can tip me on thingiverse :-)https://www.thingiverse.com/scrachi/about

thingiverse

free

Volvo C30 S40 V50 C70 USB Charger by peterlee

...up, i used spade terminals, an inline fuse and wired it into the back of the 12v socket. the...

thingiverse

free

BN-VH105 dummy battery for JVC GC-XA1/2 by laserguru

...nesses around 22awg it probably bears highlighting that you lose the water resistant feature of your camera while using this mod.

thingiverse

free

ESP32 CAM Programmer by telboy2002

...gin's with seperate power. 4 indicator and 2 front and rear light sockets. 1 x horn (buzzer) socket switch puts gpio 0 to gnd

thingiverse

free

Anet A8 PSU cover with switch, relays, fan and OctoPrint

...e psu. so i moved the opi above the psu attaching it to the anet frame with this simple holder. all the interference disappeared.

thingiverse

free

3 AAA battery holder by mpete53

...f battery's photos show, how when loaded the one end sticks out a bit, how it looks assembled and how the wire ends are made.

thingiverse

free

Step Down Buck Board Voltage Converter Upgrade for Prusa i3 MK3 MK3s by mcfada

...p to the power draw of your buck converter. i chose to power a raspberry pi 3 b+ and tft touchscreen running octoprint, pictured.

thingiverse

free

3D Printed DC Motor/Generator by papajohnfuller

...er assignment instructions link: https://docs.google.com/document/d/10rfjquc75f35oridnkn3ucm94wlsgqmlpbugyvlsiuu/edit?usp=sharing

thingiverse

free

FatShark Goggle 18650 Li-Ion Battery Holder Case by ta5jda

...e, but cant find it now, so if it's yours i apologise. i made some changes that for me made it a bit neater and work better!

thingiverse

free

DC comics Haunted Tank by PandaMonkey

...other side. add hull gun from paperclip wire or small rod. mount for .50 caliber mg on commander's hatch, add mg if desired.

thingiverse

free

Case for LM2596S DC Buck/step down converter by Modge1981

...o fit. i set infill to 100% but in all honesty its that small and with a 0.8mm nozzle there are very few areas that need infill.

thingiverse

free

VHM-306 Bluetooth Amplifier

...ut coils, becouse they are hotter than a amp chip. the foots is glued with cyanoacrylate. case dimensions: 78,4x88,4x45mm (lxwxh)

thingiverse

free

Pergo 15 Watt Amplifier Case (with XL6009 DC to DC converter) by Pergo

...-dc-adjustable-step-up-boost-power-converter-module-xl6009-replace-lm2577-fad/182891738028?hash=item2a953273ac:g:mxsaaoswnanz4hrq

thingiverse

free

Dule AC DC Monitor Stacked by MakeiTeZ

...pdates*****update 9/18/2018 uploaded new stl file with corrected opening for top monitor also added a hole in the back for wires.

thingiverse

free

Mean Well SE-600 Power Supply Cover by unknown_lamer

..., i have corrected the depth in the stl so there shouldn't be any problem but i haven't had a reason to reprint mine yet.

thingiverse

free

Mobile lab power supply by duke24

...-60 and the mpx-plug are for charging the 18650 batteries. the mpx-plug is the balancing connector. wiring diagram follows later.

thingiverse

free

Ultra bright bike light for under 3€

...power mine straight from the e-bike battery using a dc-dc stepdown converter. check out my half-encasing for stepdown converters.

thingiverse

free

Cool Moai by KidSwidden

...when printed as a transparency, the used of a wired led is implied. when wiring, note that one can...

thingiverse

free

MiSTer USB-C Power Delivery dongle by d0pefish

...ngratulations! you now have a neat way of powering your mister. if you like this idea, please consider visiting my ko-fi. thanks!

thingiverse

free

ATX PSU XT60 conversion set

...e you need out of the supply. i tested it with this connector: https://www.tme.eu/pl/en/details/xt60-m/dc-power-connectors/amass/

thingiverse

free

Fanduct5015 for TenLOG D3 PRO by StikkaDesign

...grades (bltouch, led lights, etc.) the rectangular holes are for the electrical clamps and the internal wiring of the fan cables.

thingiverse

free

Arduino Simple garden by mochr

...ews,nuts silicone tube 5x3mm dc toy motor screw din 914 - for fix shaft and motor (ac glue :) ) battery pack, i use 4xaa flower:)