18 warthox 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Warthox GR-16 Mount by Leo_N
...the warthox frame.
it is designed to the hold the graupner gr-16 receiver by means of a zip tie (2.5mm wide) in place.
enjoy,
leo
thingiverse
free
Warthox Center Plates 600TVL Cam Holder by Rangarid
... plates 600tvl cam holder by rangarid
thingiverse
can be zip tied to the warthox center plates when using 10mm aluminium pofile.
thingiverse
free
Warthox Center Plates 600TVL Cam Holder by Rangarid
... plates 600tvl cam holder by rangarid
thingiverse
can be zip tied to the warthox center plates when using 10mm aluminium pofile.
thingiverse
free
Warthox Gear Platform by Leo_N
...dded options like slots for velcro® fasteners, a notch for the gps cable and a holder for foam material to cover the baro sensor.
thingiverse
free
Warthox GPS Mount by Leo_N
...ective-shell-for-pix-px4-pixhawk-p-1005394.html
the module is easily held in place by simply snapping it on the mount.
enjoy,
leo
thingiverse
free
Quadrocopter LiPo Holder for Warthox Frames by valid0r
...crews of the lower plate.
can be used together with gzebedin's awesome landing skit (http://www.thingiverse.com/thing:103143)
thingiverse
free
Warthox Lipo Protection Plate by Leo_N
...te to protect the lipo from getting damaged by the protruding frame screws.
part printed in pla weighs aprox. 7 grams.
enjoy,
leo
thingiverse
free
Warthox Landing Skid by Leo_N
...for a nicer appearance and i also added holding tabs for the receiver antennas.
printed in pla each leg weighs 7 gram.
enjoy,
leo
thingiverse
free
Flyduino Warthox 3D printed clone by hkazmi
...mazing, much better than my dji x450 frame based quad. with pi settings on kk2.0 board bumped to 100, its control is razor sharp.
thingiverse
free
MAVLink-OSD Holder (Warthox) by Leo_N
... if necessary or you what new features to the design.
also please post a picture with comments if you have made one.
thanks.
leo
thingiverse
free
Battery compartment for Warthox frame and landing gear by marian42
...batteries that fit within a 43mm x 24mm x 136mm volume.
print without supports.
requires 3 m3x6 screws and 3 m3 nuts to assemble.
thingiverse
free
Warthox Lipo Holder by Leo_N
...der_3s_leo_n.stl" that is specifically designed to be used with my protection plate http://www.thingiverse.com/thing:2265526
thingiverse
free
Quadrocopter landing skid for Flyduino warthox frame by gzebedin
...can adjust them :-)
printed with 0.4 infill and pla its 10g per leg. one can get it down to 6-7g i guess but for me this is ok.
thingiverse
free
Battery Crash Casing for Warthox Quadcopter Frames by OoiTY
...0cm-arm
the battery it's designed for; http://www.hobbyking.com/hobbyking/store/__9957__zippy_flightmax_4000mah_3s1p_40c.html
thingiverse
free
Lipo Holder by MORP
...are following the dimensions (30.5 mm) of a standard warthox ...
thingiverse
free
WARTH250 - simple quad frame by jaysonragasa
...is a very very simple miniquad frame based on warthox frame but this one is for...
thingiverse
free
QUADCOPTER FRAME FOR SQUARE TUBE ARMS by giek2000
...the arm if fit is too loose. based on warthox ...
thingiverse
free
Quadcopter ESC Holder by MORP
...a small box to be mounted below a standard warthox frame that will hold four esc's as well as...