26 wall iot 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Helium IoT hotspot bracket
...this bracket lets me hang the helium on the wall ...
thingiverse
free
Hudl 2 Wall Mount by Neptune_Colt
...mount made for hudl 2 as to control my iot ...
thingiverse
free
Electric Wall Box Plate by petersnows
...inside the box. it's useful when placing automation devices (iot shelly, ...) inside the wall box. i advice to...
thingiverse
free
3D Printer Safety Shutdown - Smoke Detector by henryarnold
...off action. i did this by adding a 5v wall transformer to the "normally off" side of the iot...
thingiverse
free
AquaBot IoT project case by Scorpio9999
...motor driver and thermometer pcb can be glued to wall inside. power cable input below power switch. there are...
thingiverse
free
IoT Sentry by trsills
...is attached within the housing using the detector’s included wall mounting bracket and screws. the leak detector currently is...
thingiverse
free
Blink Sync wall clip
...wall clip thingiverse i wanted to neaten up my iot stash in the cupboard as there were wires everywhere....
thingiverse
free
Miniature Stevenson Screen by robertmx
...i designed a 3d-printable stevenson screen for mounting on wall or posts. for more information and the circuit, please...
thingiverse
free
Skullcrawler by redbot
...led flame bulbs: https://smile.amazon.com/gp/product/b07yc8dh7z this is wired to a wall plug which i can then plug directly into a...
thingiverse
free
Arduino node with battery by kpr
...to add your custom shields. usb connector is behind wall to block first hack attempts ;-). please note this...
thingiverse
free
Simple Hooks Mega Pack - 1 & 2 Screw - J-Type - Assorted Sizes by lsummers
...hooks (both 1 & 2 screw). countersunk, intended for drywall screws. it prints on the side for maximum support,...
thingiverse
free
Corner LED lamp by yeoldeporkpie
...cheap and gives enough of light to decorate your wall (https://www.amazon.ca/gp/product/b07wd6l31k/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=utf8&psc=1) a small esp8266 dev board -- i'm using...
thingiverse
free
Epaper display by smily77
...has a technical approach but isn’t dominant on the wall the printing was surprisingly difficult. sanding the edges might...
thingiverse
free
Hexagon lamp by DH_Beng
...lamp by dh_beng thingiverse hexagon lamp this is a wall mounted lamp for indirect lighting. it is assembled using...
thingiverse
free
WEEDO X40 Filament Bucket by TheMultiMaterialPrinter
...where filament would be caught on the outer most wall. v2 stl comes in 1 direction and does not...
thingiverse
free
Plantbug by Deformist
...accuracy due to tight tolerances (snapfit). printed with 0.8 wall 20% infill. lid upside down with supports. disclaimer: do...
thingiverse
free
Pancake IoT project box 1 - ESP 8266 / Arduino 2560, OrangePi, RaspberyPi, ultrasonic sensor, pasive infrared, lipo or AAs 2 upto 6 batteries by truhlik_fredy
...it can accommodate lot of possibilities. back can be wall mounted, can contain qr codes, be clean or have...
thingiverse
free
In-wall Hue Dimmer Mount by Shamlian
...controls power to the bulbs, just in case the iot gods aren't smiling at any particular time), but i'm...
thingiverse
free
IOT Bedroom Lamp - ESP32 with 497 LEDs by arcademachinist
...at the base, go into holes drilled in inside wall of the base and plastic holder (lampwireholder) is inserted...
thingiverse
free
LTB Weather Station by RobWLakes
...not require really hi-res printing eg no wafer thin wall. however it will produce a robust system that people...
thingiverse
free
Plug-In Motion Sensing Night Light by blacklabel775
...100% infill to prevent light from leaking through the wall and showing your infill. parts list: sonoff sv (could...
thingiverse
free
Prusa Touchscreen 3.5" with Raspberry Pi 4b and a Fan v4 kit by RockLava
...you only have to reprint the rear cover with wall i am using a raspberry pi 4b 4gig and...
grabcad
free
IOT BOX
...iot box grabcad main relay box wall mount for iot smart houses that controls lights. for...
grabcad
free
One piece wall mount
...a modern single-piece clamshell polypropylene case to house an iot device and secure to the wall. modeled in solidworks....
grabcad
free
ESP8266 Smart touch wall socket
...esp8266 smart touch wall socket grabcad iot enable smart touch wall socket , just connect to...
3dwarehouse
free
IOT Office
...office, consist of 3d printer, iot lab, and 30feet wall ...