20 turning ssr 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
SSR enclosure by shingabiss
...is a case for an ssr for use in turning a heated 3d print bed that is ac powered...
thingiverse
free
Duet3 Enclosure by Chasedog
... pi start-up to load the duet web controller and have a monitor connected to the hdmi.
using the ps_on and 5v to turn o/i the ssr
thingiverse
free
AC Bed SSR Box
... pad and ssr, check this tutorial - 120vac silicon bed controlled by ssr - 3d printinghttps://www.youtube.com/watch?v=rjmcizg2v5g
thingiverse
free
Heatermeter Sous Vide Enclosure by wbegg
...termeter forum here ...http://tvwbb.com/showthread.php?64200-sous-vide-setup
you'll need to print with supports for the case.
thingiverse
free
Sur-ron rear fender, race number plate
....m4902. l9144
orhttps://www.ebay.de/itm/1x-hinten-fender-kotflugel-passt-fur-honda-xr50-crf50-bikes-ssr-dhz-mudguard/113975273381
thingiverse
free
Versatile medium-duty SSR-controlled power outlet enclosure
...y rearm controller and about 1m of wire, which would be 3.3v from the lpc1768. the led barely lights but the heater does turn on.
thingiverse
free
DIY Rework hot air station by Scrachi
... wiring explanation soon...
<= if you like my work, you can tip me on thingiverse :-)https://www.thingiverse.com/scrachi/about
thingiverse
free
PopLite Coffee Roaster by faithhack
...of the roaster in action on my back porch. i didn't have a chafe catcher at this point so was relegated to roasting outdoors.
thingiverse
free
RepRap Electronics Assembly V2 - Modular Attempt by Maaarsl
...eter for fan control (optional)
1x switch (optional)
just in case you're thinking in imperial units: 1 inch equals 25.4 mm :)
thingiverse
free
3D-Printer control box by TsarBombe
...unt, with/without psu mount).
the hole for the cable mount is 13,5mm. the cable clip is mounted with m3 brass inserts and screws.
thingiverse
free
Firebrick Mold by swirlingbrain
...it by putting an allen wrench in it and turning it to separate. i then only used about 85%...
thingiverse
free
Case for Ramps Full Graphics and Raspberry Pi Zero for Octoprint with ATX Power Supply Control by sricanesh
...older is different from the photo. after printing i realized that the stand should be in front of the cable entry and not behind.
thingiverse
free
Da vinci 1.0 MK3 alu heatbed upgrade by technomastermind
...st.
has explained in previous posts please turn on build plate pre-heat to prevent your printer firmware timing out on you.
enjoy
thingiverse
free
Proteus Power Control by ProteanMan
... if there are any issues or concerns or ideas.
any ideas for add-ons please let me know! other clip types, front tray types, etc.
thingiverse
free
Triple lumen Bio-Printer head by siderits
...ake the channels 100 microns and i can add an inner mixing chamber if needed. i'll add a side viewport for a camera as well.
thingiverse
free
Pergo Robo3D Upgrade, NeoCeram Glass and 600 watt(110v) heater by Pergo
...woo hoo!! i love this bed heater! also with turning off bang-bang and putting the pid (kpi) vars, the...
thingiverse
free
Dual or single DPS-1200FB power supply mount by earlynerd
...the power switch only to their enable/disable pin for turning the whole unit on and off. that would be...
thingiverse
free
GeitPrinter by geit_de
...(magnetic parking)
2x m3 15mm counter sunk enclosure screws (e3dv6 fan)
8x 4mm cubic neodymium magnets (magnetic parking)
thingiverse
free
Anet A6 - Autolevel bed sensor Blue SN-04N by d3adlydozen
... you have a buzzer with a fixed frequency.
//
//#define speaker
//
// the duration and frequency for the ui feedback sound.
// se
grabcad
free
Panasonic Solid State Relay AQY212GH
...ntrol voltage range 1.5 → 5 v
operating temperature range -40 → +85°c
load voltage range maximum of 60v
depth 4.78mm
height 2.9mm