28 t voltage coil 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Tesla coil DIY by derrick84
...the transformer out of the microwave for my high voltage its still a work in progress just added toroid...
thingiverse
free
Tesla Coil Primary by ldm314
...heater circuit for the primary:https://www.youtube.com/watch?v=a7rzmr6kdds running at low input voltage to start with making a little music:...
thingiverse
free
Mini Tesla Coil Base by rogbigras
...where i got max feedback and and highest junction voltage i'll make a youtube video one...
thingiverse
free
Red Alert Tesla Coil Plasma Globe by -IDDQD-
...this if you aren't confident about handing very high voltage power...
thingiverse
free
Tesla Coil 3D Printed - Desktop 2 x AA by SoPro
...researching full diy tesla coils that use low input voltage. growing up i had a few kits as a...
thingiverse
free
Tesla Desktop Lamp & Charging Station by SoPro
...way to show off wireless power using a harmless voltage to power a normally 120v bulb. i did prepare...
thingiverse
free
3d printed vacuum tube transmitter by SA2CLC
...small transformers back-to-back and rectify to get a high voltage source. to modulate the transmitter, use a carbon mic...
thingiverse
free
Wireless POV Clock by KiwiGrinder
...rewritten the code to use timer1 to measure the rottion speed and timer2 to output the leds based on...
thingiverse
free
Vertical Wind turbine and 3Phase alternator 9 Coils / 12 magnets by iZe
...rev 0.10 5/7/15 - after a first test the voltage is way too low, around 6-7v, and i choose...
thingiverse
free
12V Ozone Generator by Klave
...very similar to this one. it has a high voltage transformer in an encapsulated plastic enclosure and a ceramic...
thingiverse
free
Another Parametric Spool by IronOxide
...of motion and i'm just trying to get enough voltage to power an led but haven't been successful thus...
thingiverse
free
Electric Generator by tdavidson1
...make less. i wasn't able to get any significant voltage when i used the crank. also, make sure you...
thingiverse
free
xbox 360 controller 18650 battery holder by 3Dummy
...batteries on xbox 360 wireless controller. important notes 1) voltage will be a little higher than regular batteries since...
thingiverse
free
The Anti-Gravitator Thru-Hole Version by dewhisna
...used are: 1 - mcp1702-5002e 5v, 250ma ldo to-92 voltage regulator (digikey: mcp1702-5002e/to-nd) 1 - ne5532p opamp (digikey: 296-1410-5-nd)...
thingiverse
free
BLTouch / 3DTouch Alternative Z-Probe by svogel7808
...in place of the pot to create a 1:1 voltage divider. the board is then connected to the printer...
thingiverse
free
8/9 Coil for Microscope by Alvinyeahalvin
...haha. printed on abs or pla. regular temp. no support. ...
thingiverse
free
Free-piston Stirling engine by IronGoober
...light an led. i have yet to check the voltage coming out of it. in the video, boiling water...
thingiverse
free
Ugrinsky Wind Turbine (VAWT) with built-in Generator by QuadeHale
...for magnets and coils. i have no idea what voltage will get generated, but one way or another, it...
thingiverse
free
Quiet Raspberry Pi 4B case with active cooling
...the potentiometer with a small screwdriver, adjusting the output voltage single power source drives both the pi and the...
thingiverse
free
Remixed Left Case by pigaro
...v output up to 6 a (depending on input voltage. the dc-dc converter has both a usb-a connector and...
thingiverse
free
RF Item Tracker by littleStrong
...• resistance-frequency-capacitance calculator -- https://www.pad2pad.com/calculators/resistance-frequency-capacitance/ components list • 5volt voltage regulator -- https://www.mouser.com/datasheet/2/389/cd00000444-1795274.pdf • dpak package -- https://toshiba.semicon-storage.com/ap-en/semiconductor/design-development/package/detail.dpak.html •...
thingiverse
free
Ender 3 60mm Hot End Fan Mount by Spud_Munky
...just a resistor in a wire to reduce the voltage so the fan spins at 1600rpm, i used a...
thingiverse
free
Auto Power Off Project by Botcan
...of the printer). warning: safety first! dealing with high voltage (ie 110/220v) is dangerous and may harm you or...
thingiverse
free
Auto Power Off Project by Botcan
...of the printer). warning: safety first! dealing with high voltage (ie 110/220v) is dangerous and may harm you or...
thingiverse
free
Anet A6 - Autolevel bed sensor Blue SN-04N by d3adlydozen
...if enabled, the solenoid is not magnetized with applied voltage define parking_extruder_solenoids_pins_active low // low or high pin signal...
grabcad
free
Omron 3 GHz RF DPDT SMT Relay
...both latching (g6ku-2f-rf-t) and non-latching (g6k-2f-rf-t) with operating coil voltage of 3.5, 4.0, 5.0, 6.0, 9.0,12, and 24 volts....
grabcad
free
Omron 3 GHz ~ 5 GHz RF DPDT SMT Relay
...both latching (g6ku-2f-rf-t) and non-latching (g6k-2f-rf-t) with operating coil voltage of 3.5, 4.0, 5.0, 6.0, 9.0,12, and 24 volts....
grabcad
free
High Intensity Bar Clamp Mounted LED Light - 10 Watt LED - 12-32V DC - 650 Foot Spot Beam
...a very tight spot pattern, can run on any voltage from 12 to 32 volts dc and provides a...