20 speed syringe 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
SR Aquaristik Speed Test Expansion Rack by Alexjoha
...5 slots for redsea viles 1 slot for 10ml syringe v2 has better clearance for the syringe and fillet...
thingiverse
free
Printerbot Syringe Adapter for Bioconductive Gel
...gel still needs some fixing need to change printing speed to 3 mm/s and filament to...
thingiverse
free
60ml Syringe Extruder for Liquid Deposition Modeling - LDM by piuLAB
...slow down all head movements like print speed, travel speed etc. the gear reduction ratio is 5:1, which is...
thingiverse
free
Speed & Power - Coaster & Caddy by Lycan004
...heads the lettering .stl is available. or use a syringe to deposit paint (nail polish) in the lettering for...
thingiverse
free
Medication Supplies Organizer for IVF by KT421
...a printrbot metal simple, but would probably increase those speed to 80mm/sec if i were to print it...
thingiverse
free
Arduino Motorized SMT Solder Paste Dispenser by zapta
...logarithmic mapping to allow very fine control at low speed. this design is specific for the bd syringe listed...
thingiverse
free
Paste extruder (clay) by Daniele_Dondi
...order to find the proper clay/water ratio and printing speed the use of an hair-drier pointed close to the...
thingiverse
free
Stepper-driven paste extruder for Delta-type printers by jgunn
...times. you are limited in print speed (well, extrusion speed by the viscosity of the material you are extruding....
thingiverse
free
Simple Syringe Paste Extruder by sr6imp
...storing, remember to disable with m302 p0 afterwards). print speed i used 20mm/s, worked very well, i guess you...
thingiverse
free
Hydraulic Robot Arm 6-Axis by Blastronauticus
...a 0.2mm nozzle and 30mm/s for the outer wall speed but 0.3mm or 0.4mm might be...
thingiverse
free
pneumatic extruder clamp, carriage adapter, and solenoid bracket by nicksears
...it will begin with a loop tat the average speed that will allow you get a ballpark pressure with...
thingiverse
free
Coffee spoon-scale - measure right from the scoop! by phckopper
...without supports at 0.16mm dynamic layer height and 75mm/s speed the counterweight should be a snug fit, sand the...
thingiverse
free
precision paste extruder based on screw frosting device by nicksears
...calibration by 10^2 will cancel out. this will make speed more comparable to traditional 1.75mm filament. and a linear...
thingiverse
free
Pwdr Model 0.1 by Pwdr
...print resolution (3dp): 96dpi minimum vertical step size: 50î¼m speed (depending on printed part): â±1 minute per...
thingiverse
free
Solder paste dispenser for less then $5 by jldesigns
...also be shorter. add a potentiometer to change the speedretraction length. design custom pcb adjust screw hole size and...
grabcad
free
Test setup for droplet impact on surface
...for droplet impact on the surface. syringe pump, stage, high-speed camera, and...
grabcad
free
Tecan Cavro Syringe Pump with Arduino Uno
...the - dispense time - pause time - dispense speed with poti. except the pump and the housing, all...
grabcad
free
Bi Cylinder ventilator pump
...head cover to join hold all parts together motor speed could be controlled by additional controller to the desired...
grabcad
free
Bi cylinder Air pump ventilator
...head cover to join hold all parts together motor speed could be controlled by additional controller to the desired...
cg_trader
$12
THE BLADE OF EVILS BANE MASTER SWORD | 3D
...pieces in the direction of movement and reduce printing speed to minimize wobble while printing. the cross guard can...