26 solder 6x 5 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Maiskolben Case by Zellech
...zellech thingiverse this is a case for the "maiskolben" solderng station ("make: edition board") described here: https://www.heise.de/make/artikel/platine-fuer-diy-loetstation-maiskolben-3569923.html attention: this...
thingiverse
free
Type 2 EV socket wall mount + cover by henkgroenewold
...printing) 6x hex holes for hex nut (best to solder iron to burn/melt them in) 6x 4 mm stainless...
thingiverse
free
Anycubic Mega X Hemera mount by usinguser
...5015 radial fan soldering iron, different wire colors and solder for the cable...
thingiverse
free
Arduino handheld arcade cabinet by Mehozavr
...piezo buzzers power switch 3 aa battery holder 50*70 solder board 6x 12*12 tact buttons with caps m3 and...
thingiverse
free
Raspberry Pi Camera Case Back for 6x 5mm LEDs by adafruit
...the anode (longer leg) of a led is directly solderd to the adjacent led cathode (shorter leg). a 5v...
thingiverse
free
Resistive Decade by toosha
...10ohm to 1m (10 -10.11mohm). all resistors are directly solderd between switch pins 1-2,2-3,3-4...10-11. other wires goes in series...
thingiverse
free
Corner clamp by Bastien
...base. insert the m8 nuts in place, use a solder iron to heat the nuts so that they melt...
thingiverse
free
360 GoPro Hero 4 Mount for 5 or 6 Cameras by mtanu
...to access buttons. for the extension stem, using a solderng iron, heat up a 1/4-20 (m6) nut and push...
thingiverse
free
RC Wheel Adapter for Robomow by raeuberhose
...a m8x12,7 threaded insert, which was installed using a solderng iron. a m4x20 flat head screw connects the adapter...
thingiverse
free
Wi-Fi Laundry Alarm by ReallyBigTeeth
...(for programming the wi-fi breakout board) soldering iron and solder electronics side cutters sharp knife wire strippers sand paper...
thingiverse
free
Dual Power Supply Front End - alt lab supply by MCmaks
...the temp gets high enough to melt the solder). solder red wires: dc jack+ to switch_in, switch_out to dc-dc...
thingiverse
free
Open source terp temper v0.2 by disassociatedusername
...connector buck converter dupont wires, but you can hard solder if you’re braver than i 21mm panel mount on/off...
thingiverse
free
Bike Hoist (35lbs max) by cyamate
...tin snips to make a positive and negative terminal. solder wires to those terminals and solder the other ends...
thingiverse
free
Servo Spine Robot - Richard 9000 by Gear_Down_For_What
...the tubes - dont use graphite) https://amzn.to/2n6tbzc soldering iron solder 6v power supply, 5 amp if using the 6v...
thingiverse
free
Easier Useless Box TowerPro SG90 by blarbles
...screw holes. you could also just superglue the switch) solder and soldering gun instructions modify your tower pro sg90...
thingiverse
free
Mantis Stereo Microscope Long Working Distance (SLWD) objective lens adapter by DogP
...0201s, etc.) is that it's hard to get the solderng iron(s) and/or hot air tool at the necessary angles...
thingiverse
free
Formula B1 - (Sim racing) steering wheel
...four m3 inserts into the enclose. i used a solderng iron to push them in. but perhaps you can...
thingiverse
free
Stranger Things Fiber Optic Lamp by Van_Houten
...with some building experience and a small amount of solderng skills you can make this as well.) 1-tips glue...
thingiverse
free
CR-10S "The Last Stand" Mod by Prostakarnik
...hardware needed before you stard actually printing. wire strippers solderng iron and solder - for some cable connections. multimeter...
thingiverse
free
Arasaka Thermal Katana - Cyberpunk 2077 by JokerToolWorks
...self-tapping screw. route wires along channels, might have to solder the wires together if there's a connector. 10) secure...
thingiverse
free
Electric Spinning Wheel by ChPech
...6903 bearings: https://www.aliexpress.com/item/10pcs-bearing-6903-6903rs-61903-2rs1-6903rz-17x30x7-abec-3-mochu-thin-section-shielded-deep-groove/32581561929.html ky-040 rotary encoder: https://www.aliexpress.com/item/5pcs-lot-ky-040-rotary-encoder-sensor-module-for-arduino-free-shipping-dropshipping/32293140596.html arduino nano: https://www.aliexpress.com/item/nano-v3-atmega328-ch340g-micro-usb-pin-headers-not-solderd-compatible-for-arduino-nano-v3-0/32664577152.html sm2.54 connectors: https://www.aliexpress.com/item/sm2-54-kits-20-sets-kit-in-box-2p-3p-4p-5p-2-54mm-pitch-female/32699760809.html...
thingiverse
free
6 cylinder radial 'steam' engine by Xaxis
...x m3 brass knurl nuts, heat inserted with a solderng iron into the crank case. guides are available through...
thingiverse
free
200 Watt Bluetooth 5 Speaker Boombox *Source Files Included!* by morganlowe
...volt power so very easy to use. it has solder tabs for buttons and isn't crazy big or small....
thingiverse
free
ReDuplicator i3 MK3x - Wanhao i3 Complete Aluminium Extrusion & Prusa Mk3 Overhaul by OmNomNomagon
...similar. these are set into parts using a hot solderng iron and are great for making strong functional parts...
thingiverse
free
MyRCCar 1/10 Truggy Build for FJ Cruiser Body by dlb5
...sand and drill piano wires and maybe your hand) solderng iron if you have to make some magic with...
thingiverse
free
DemonDeltaMicro - Simplest reprap delta frame to date. by DjDemonD
...unimportant) to the d8 mosfet output. do not use solder on the wires as it tends to deform and...