19 separated separation micron 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Cyclone Separator for 5" hose Diameter by M_Brownies
.... if this information is correct this could be effective down to 7 microns with minimal pressure drop depending on air velocity.
thingiverse
free
Robotroid (inspired by 30 rock robot) by cerberus333
...gether.
simple to scale as all parts scale together
my print was
abs
100mm tall
300 micron slice
0% infill
acetone vapor polished
thingiverse
free
AGV pinlock clip by T0bs
... my own clips!
printed with support, 20 micron layer height in abs.
i used an 8mm philips screw (1.5mm wide) to fasten the clips.
thingiverse
free
Blower/Vac to Dust Collector by PCFlyer
...acuum-mulcher-62337.html
http://www.amazon.com/gp/product/b002dsc09q?psc=1&redirect=true&ref_=oh_aui_detailpage_o07_s00
thingiverse
free
Jack'O Lantern rev 3 by cerberus333
...s on the edge of the lid and the top of the lantern.
i use a hot acetone vapor polish to shine it up (top and bottom separately!)
thingiverse
free
Ghostbusters Belt Gizmo - Reinforced & Remixed by WindDrake
...to the board and glue. i then went and separated the nixie shelf from chrischkula's belt_gizmofinished-_demo.stl in netfabb so...
thingiverse
free
Bed Level Correction Calibration Squares by makeryo
...4 outer squares (and center square) printed with an equal squish. further live adjust z will set all sides equally going forward.
thingiverse
free
Low Poly Woman by axtn
...as well (belly flattened a bit, rear raised, thighs separated. my make in the picture was 3d printed with...
thingiverse
free
Printable Hinge Easel by akshay_d21
...
thank you!
model update [06/04/2018]: an easier model has been added. print in place and usable without any kind of assembly.
thingiverse
free
Coffee filter holder by Terminus
...r causes trouble, and your printer can't build that angle without dripping filament over the edge, then give it some support.
thingiverse
free
Cosmic Encounter Game Board by DROP_DB
... as well, but i am not personally familiar with them. please leave me a comment if you print this and use it for another edition.
thingiverse
free
Caliburn Mag-Fed Pump-Action Nerf Blaster by captainslug
...ies are available for sale on etsy.
https://www.etsy.com/shop/captainslug/
http://captainslug.com/nerf/caliburn%20materials2.xls
thingiverse
free
Legacy RS232 to WIFI adapter for Cell Phone App by nafis
... lcd.print(1,1,"poor");
else
lcd.print(1,1,"very poor");
}
thingiverse
free
Triple lumen Bio-Printer head by siderits
...ake the channels 100 microns and i can add an inner mixing chamber if needed. i'll add a side viewport for a camera as well.
thingiverse
free
COVID-19 Respirator with Activated Carbon Filter & Exhalation Valve by adamariffin
... hear of any build issues you may have. crank it out and distribute to the vulnerable without access to store-bought respirators.
thingiverse
free
Replicator 2 Extruder Upgrade by whpthomas
... sure not to wet the bearing). once soft, bend the arm back to how it should be and allow to cool, then re-install - good as new!
grabcad
free
HYDROCYCLONE SAND SEPARATOR 1'' BSPM PLASTICA ALFA
...ng pressure: 5 bar - 72.5 psi
max. flow recommended: 1,7l/s - 26,9 gal/min
filtration: <70 microns
working temp.: -10ºc - 95ºc
grabcad
free
Oil & Diesel Filtration System (CJC)
...in line with water sensor and solenoid valve ,flow switch at the end of water drain line, diesel drain line , automatic air vent,
grabcad
free
Face Mask with Replaceable Filter Element
...areful not to burn the intended user. a handkerchief between the mask and skin while forming may be helpful in preventing burns.