26 rod junction 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
junction for rods by moreken
...or rods by moreken
thingiverse
junction for rods for my printer 3d "moredelta"
amended to simplify printing 13/10/2015
thingiverse
free
OO/HO Point Rodding Junctions by calvinstreeting
...ranks, straight and curved
1x compensator crank, shoe and rod ends
for straight rods see http://www.thingiverse.com/thing:2169509
thingiverse
free
Lower arm junction by jeffersonbenson
...thingiverse i needed a thing to connect some dowel rod to a lower support structure for my rostock printer,...
thingiverse
free
SIDE TABLE by ovocom
...: 10 mm plywood base : 16 mm mdf rod : ΓΈ 35 x 660 mm (curtain rod in...
thingiverse
free
Tevo Z-Base by dddienst
...the oldhams removal of any z wobble in the rod ...
thingiverse
free
Knucklebuster lounger by E_T
...at the moment the surface is fixed via m6 rod through each of the joining junctions although would be...
thingiverse
free
Tillig TT scale flexbed guide by jurazbabic
...tilligs tt scale (1:120) flex beds and 2.07mm rail rod. endstop is to position rails just to put junction...
thingiverse
free
Fishing rod butt clamp remix by kfj
...two uprights were totally not strong enough at the junction with the horizontal member to take the strain of...
thingiverse
free
surf fishing tripod by M___B
...6 staj3 2 tri 2 cup 2 t 2 rodrest_u this is my first upload to the site. asking...
thingiverse
free
Just mine ADJUSTABLE SPOOL HOLDER in a FILAMENT DRYBOX SET by daveleonelizzi
...an air pipe junction, 90/110 mm of m6 threaded rod and some m6 nuts and screws....
thingiverse
free
M1GEO/G8OCV Moxon Antenna with 9W2FLP Accessories
...constructed using 20mm pvc electrical conduit with 3mm brass rod. however, it is hard to mount the element just...
thingiverse
free
ANET A8 exoskeleton by aeropic
...stiffness is brought by 2 pieces of 6mm carbon rod or carbon tubes (go and search on ebay or...
thingiverse
free
Smallest 3D Printer in the world by eserretti
...smooth bar 8x182mm n.2 smooth bar 8x250mm n.1 m5 rod bar 160mm n.1 t8 neverending screw 8x200mm n.1 t8...
thingiverse
free
Reloading Over All Length Gauge by Archer60x
...a m3 nut and bolt to hold the push rod i also had good success using a guitar string...
thingiverse
free
My Personal Spool Holder by Sinkha
...was excellent as well as very resistant. as post prodction using the pla maybe you have to sand a...
thingiverse
free
3D Catan Tile Magentic Storage Board by BK_235
...steel rod into before adhering the board together. the rod themselves were readily available from amazon and i cut...
thingiverse
free
CloverPlus v2 Delta 3D Printer by pbmax
...video: https://youtu.be/dcsyj_gux3u octoprint timelapse: https://youtu.be/2u4mggkmk7k calculated v2 delta variables rod center to plate center = 100.429 carriage to ball...
thingiverse
free
Tumbler cyclone rotary case deburring machiine
...the central section to get the shortest version. m8 rod should then beeing adjusted to fit. lego tyres must...
thingiverse
free
DJI Easy Snap-On Prop Guards by giufini
...the junction points between the horizontal and vertical curved rod (snaponpropguard_v2.stl). you don't need any fixed part at the...
thingiverse
free
Table Saw(Need Flexible Shaft) by Jim777
...bolt(anything 'hex' or '+') x 10 20 mm brass rod (can be omitted if you do not have it)...
thingiverse
free
Z-X rev 0.05 - Creality Mod by Dan_W_58
...between the vertical extrusion bar and the z-axis all-thread rod from which cables will emerge to go to the...
thingiverse
free
Geeetech i3 Clone V2 - Z axis by valand70
...and materials for my printer, prices are excellent and prodcts are good. if you buy something from here you...
thingiverse
free
Curved illuminator for Ciclop 3D Scanner by elhalpern
...above and below over-hangs and snaps onto the threaded rod easily. too many hours of fun... my choice of...
grabcad
free
Rocket pad base
...using 3 .5" square legs and a .25" vertical rod this junction piece supports a model rocket for...
grabcad
free
Knuckle Joint
...junction is a knuckle joint that links two cylindrical rod under tensile strain. in other words, we may say...
grabcad
free
Diamond "3D Printing Egg Drop Challenge"
...main parts : diamond structure with the egg inside. rod who absorb shocks. junction parts. inspiration : diamond and...