28 polar friction 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
50mm polarized lens pair holder by jcomtois
...bench. the frame and base are joined by a frictionfit 5mm metal rod that allows the height to be...
thingiverse
free
Better Laser Polar Alignment for Astro Tracker by ovisual
...universal slot) the laser unit stays in place by friction the cap that holds the laser can be fixed...
thingiverse
free
Magnetic fidget by Jori
...diameter 5 by 3mm. put them in with opposite polarty. lower part has a hole in the bottom to...
thingiverse
free
Magnetic Dust Hose Connector by furfoxsake
...make sure that you dont mix up the magnets polarty or it will not work. they turned out to...
thingiverse
free
Stratasys Mojo Wavewash Agitator by Knex_Obsessed
...magnets and insert them in the provided holes. note: polarty must be switching back and forth: nsns. seal the...
thingiverse
free
Prop balancer (BoomBox edition) by Zilla99
...such that the prop is horizontally aligned to the polarzation of the rod, then try to balance. due to...
thingiverse
free
Raspberry Pi Hifiberry Amp+ Case by pezhore
...- the only changes for v2 are larger barrel polarty/voltage indicators (and they're further inset into the side wall)....
thingiverse
free
FreeTrack - OpenTrack - TrackIR LED holder
...to avoid accidentally powering the leds circuit with reversed polarty if the connectors are plugged in the wrong orientation....
thingiverse
free
AutoStryfe mod kit by kitsune109
...box mount and remember to re-solder the pusher motor polarties (flipping the gear box over will make it rotate...
thingiverse
free
Magnetic stirrer from a 80 mm fan by WaveSupportApparatus
...your stir bar to a magnet to find the polarty of each end. surprisingly, my own stir bars had...
thingiverse
free
Tricopter LR Impossible Tilt with Bearings and Crossfire Diversity
...flight relative to the ground antenna. i use vertical polarzation on the transmitter for maximum distance, since the tricopter...
thingiverse
free
Floating LED Photo Frame by onebitpixel
...left and right of the battery making sure your polarty is correct and insert cap apply enough pressure turn...
thingiverse
free
Star Wars Rebellion Magnetic Ring Base by jpod
...together as a stack. i've opted to reverse the polarty between rebel and imperial rings. this way the rebel...
thingiverse
free
"hey!! you are out of filament" alarm 1.75mm by jaykoehler
...but a 9v battery will work just as well. polarty does matter here so take a moment to test....
thingiverse
free
Magnetic Building Board Jigs by archiea67
...of super glue will help. be mindful of the polarty so you can stack your jigs when not in...
thingiverse
free
Hamster Wheel 21 cm With LED silent with bearings by LittleSheep
...them directly to the 2 motor pins with opposit polarty. this way one of the led always lights up...
thingiverse
free
Experimental 3D Printable Nema 17 Stepper Motor by PCCLDideafactory
...which will degrade the abs. use a higher-diameter diametrically polarzed magnet for a rotor for better...
thingiverse
free
Oculus Rift Rifle / Gun Stock Remix for 3/4" PVC & 6-32 screws by SodaPopin5ki
...spaces in clamps, making sure to line up the polarty. these are fairly strong magnets, so use decent glue....
thingiverse
free
Wheels for Cubelets modular robot by gpvillamil
...the magnets, be aware that there is a correct polarty for installing them. they should be oriented such that...
thingiverse
free
Perimeter Bear Alarm Fence by nenadr
...motion detectors, but they are not adequate for a polar 24hour sunlight scenario and well-insulated polar bears. the alarm...
thingiverse
free
QIDI X-Plus X-Max Extruder Fan Upgrade by humebeam
...crimp on a jst-xh connector on it. make sure polarty is correct, the red wire goes where the red...
thingiverse
free
Simple tiltable snap-in frame for G4-type LED lamps by enif
...rectifier, so that you don't have to worry about polarty. the scad file that is provided is parametrized, so...
thingiverse
free
Magnetic Filament Filter (Updated Dec 2019) by Kadah
...bare middle frame. put all magnets in the same polarty for one frame, then the opposite for the other....
thingiverse
free
Continuity tester model and upgrade by makibox850
...small piezzo buzzer for the stock tiny 10mm buzzer (polarzed! with integrated driver) i had to put a resistor...
thingiverse
free
Top-Door-Opener Ikea Lack Enclosure made stronger by paparazzi
...plexi) left put 2 mags in a triangle (same polarty orientation) + maintain top magnet with some strong tape...
cg_trader
$7
Inverted Magnetic Frictionless Axle and Bearing Kit - Concept | 3D
...correct neodymium magnets are glued into the shapes and polarties. the idea is that the shapes are attracted and...
grabcad
free
Cleveron Friction-Less Drawer
...with the electromagnet, and push by reverse the electromagnet polarty. problem-2 maximize the size of package that can be...
grabcad
free
NASA RASSOR Bucket
...mm when assumed to be 100% filled). also, the polar moi is relatively high. hence, there was no need...