27 plastic wired teflon 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Unofficial Thingomatic Heater Board v1.1 r2 by dnewman
...not address the problem associated with overheating of the plastic in the connector shrouds or their mating plugs --...
thingiverse
free
Aus3D IR Probe 1.4 Support for Diamond Hotend by LoraxWorks
...mm layer thickness. use a low shrinkage high temperature plastic preferably. make sure that no support get between gills...
thingiverse
free
Flexion bracket for Lulzbot Mini by CaptainBisquick
...machine screws will self-tap and hold directly in the plastic if this doesn't work for you, you can try...
thingiverse
free
Prusa Humidity Control by Aussie_Jo
...they are not being used, they are in sealed plastic containers with desiccant. but, when in use, mounted on...
thingiverse
free
fischertechnik adapter for slewing ring and fslip ring by thomasdr
...circuits speed: 0-300 rpm circuits: 6 housing material: engineering plastic work humidity: 60%rh or higher work temp.: -40℃~+80℃ contact...
thingiverse
free
Easy exchange filament extruder by JobSmolders
...put katon tape on the bottom to protect the plastic from all the heat. this way the plastic holds...
thingiverse
free
E3D V6 Adapter for MeCreator 2 by Martin_Printer
...sink has enough space to be mounted, with its plastic retainer on top sand printed baseplate to get a...
thingiverse
free
Chickens Whirligig V2 by Sparky6548
...thing, after most of a year outside, the abs plastic i used for this print has gotten brittle. for...
thingiverse
free
AstroX J5 frame JohnnyFPV antenna GPS Xiaomi Yi mount
...they are intended to be used with 3mm-diameter protective plastic tubing. i tested 3mmd teflon tubing with success. now...
thingiverse
free
TronXY X5S upgrades by pbannister
...very serviceable pla (mostly) printer. also note the large plastic corners are superior to metal brackets, as they force...
thingiverse
free
Folger Tech Knock-Off E3D-V6 (25MM Cooling Fin Dia.) by Zurkeyon
...tabs to zip tie the wire onto,with minimal additional plastic printing with pla, i swap out the folger tech...
thingiverse
free
Single/dual Bowden extruders with mounting for Fabrikator or other RepRap by chrishornby
...an ordinary bolt would do as it is only plastic screw in the bowden attachment. insert the bearing as...
thingiverse
free
Big DIY 3D printer 2 by JobSmolders
...bought in a cheap chinese products store. the yellow plastic peace is my template for cutting the once for...
thingiverse
free
BIG DIY 3D Printer by JobSmolders
...put katon tape on the bottom to protect the plastic from all the heat. this way the plastic holds...
thingiverse
free
2020 DRAWbot Drawing Robot by wsolstice69
...small so the screw threads will bite into the plastic be careful that you do not over tighten and...
thingiverse
free
QU-BD TwoUp Upgrade by Hogsqueal
...mechanical limit switch w/ led and wire (~$5) nylon plastic zip trim wrap ($1) 3) filament for printed parts...
thingiverse
free
Ender 4 Dual Extrusion Upgrade Guide by krestoverson
...(https://www.amazon.com/iverntech-printer-extruder-aluminum-reprap/dp/b0774jz9n5/ref=sr_1_3?ie=utf8&qid=1523207619&sr=8-3&keywords=mk8+extruder) 8.69$ (x2) i purchased two and replaced the plastic one that came with the printer. 24v heater (chimera...
thingiverse
free
Reliable Filament Runout Sensor by bwaslo
...by hand. arrange the pc4-m10 connectors so that the plastic push-cap faces away from the spool on the line...
thingiverse
free
E3D V6 Extruder Head Assembly With Cardan Shaft Direct Drive by astfaellergerald
...cooler 40mm, filament cooler 40mm, with solid screw connections. plastic weight: about 50 grams. required parts: 5 x pulley...
thingiverse
free
HyperCube 3D printer (2525 Aluminum) by brspartan
...100 x m5 x 12mm button head screws (for plastic parts) 50 x m5 x 10mm button head screws...
thingiverse
free
DDW Ronin 3D Printer (Hictop 3DP-12) by DarkDragonWing
...hictop now provides the metal cover that comes with plastic nuts to separate the lcd screen and the metal...
thingiverse
free
Adapters to attach Prosthetic Hand to Black Ram Mount and updated Pins by AlwaysTinkering
...models in places you don’t want to use the plastic screws. i added an stl for a flat sided...
thingiverse
free
Printrbot Metal Plus MMU (Prusa Inspired) by Rushmere3D
...end - https://www.distechautomation.com/products/prometheus-v2 brass inserts m3 & m6 - https://www.ebay.co.uk/itm/m3-m4-m5-m6-threaded-solid-brass-press-in-barbed-inserts-for-plastic262993790868?var=562002386626&hash=item3d3ba6c794:m:mohtfrbryivejt2c76st51w m6 pneumatic fittings - https://www.aliexpress.com/item/10pcs-pc4-m6-pneumatic-straight-fitting-connector-for-4mm-od-tubing-m6-6mm-reprap-for-3d/32668216080.html?spm=a2g0s.9042311.0.0.3a8kmo extruder gear set -...
thingiverse
free
Enlarged Rostock by kolergy
...first print: a 10mm cube, there was to much plastic feed and the hot end was too hot, so...
cults
free
Easy exchange filament extruder
...put katon tape on the bottom to protect the plastic from all the heat. this way the plastic holds...
grabcad
free
Sifter Sorter
...renderings. -materials used are aluminum, titanium 6ai-4v, and pmma plastic ...
cults
free
BIG DIY 3D Printer
...put katon tape on the bottom to protect the plastic from all the heat. this way the plastic holds...