21 oriental quadcopter 1 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Martian II/Impulse RC Alien Camera Mount for Samsung Gear 360 by Ayo_O
...
a 1/4" - 20 unc fastener with a length of 1/2" is required in order to retain a samsung gear 360 camera to this mount.
thingiverse
free
Ox FPV Thug Classic 230-H Camera Mount for Samsung Gear 360 by Ayo_O
...
a 1/4" - 20 unc fastener with a length of 1/2" is required in order to retain a samsung gear 360 camera to this mount.
thingiverse
free
Quadcopter Motor Mount (10mm Rod) ArmaQuad by Arma
...art... it needs some refining.
feel free to comment and advices to make this part better are welcome! :) scad file is included.
thingiverse
free
![Flexible Landing Gear for Quadcopter "Crossfire" Version 2 [deprecated] by leemes](/t/9021489.jpg)
Flexible Landing Gear for Quadcopter "Crossfire" Version 2 [deprecated] by leemes
... on the bottom you should check and maybe enlarge them as needed. take about 1 - 1.5cm of flexibility into account when doing so.
thingiverse
free
500mm quadcopter, fully enclosed, gopro mount built in, vibration dampened flight board, battery slide and hood by CreateUNSW
... the arms to the frame and 4 m3 bolts and nuts to secure the motor mounts to the arms. landing gear is fastened using cable ties.
thingiverse
free
Quanum Neon quadcopter GoPro mounts by UserUnrelated
..., with support material underneath) so that the print planes are not parallel with the interface between the pivots and the base.
thingiverse
free
Iris quadcopter long legs (Picatinny rail) by Brendan22
... 6 grams each (plus another 2 grams for nut and bolt if desired) ...that's about 1/5 the weight of the genuine 3dr long legs.
thingiverse
free
HoverGames Arm Mount
... if you need any spare arm mounts to replace the ones that came with the lji x4 500 kit, print the arm mount without any notches.
thingiverse
free
3D Printable Quick-Connect Quadcopter by FlightFixit
...nal version of my consumer version of the dimension 3 multimachine delta 3d printer. check it out at http://www.dimension3fab.com
thingiverse
free
Aerial Payload Basket for Quadcopters / Drones / RC Helicopters by H5Labs
... held firmly in position for aerial pick-up. if you would rather the handle be movable, just use two pins/clips instead of four.
thingiverse
free
Vertical Mount Immersion RC's FatShark FPV 600mw Transmitter with OpenSCAD Source by MichaelErwin
...37 to mount to the bar as well.
note: there are still a few little tweaks i want to make, so i might be updating in the future.
thingiverse
free
Rollkage Camera Mount for Toothpick quadcopters by Haku3D
...
tips are most welcome https://www.paypal.com/paypalme/haku3d and will encourage me to make more designs for everyone to benefit.
thingiverse
free
World's Lightest Propeller Guards for Estes ProtoX Proto X Quadcopter by TechShopJim
...cal motors (http://www.thingiverse.com/thing:243859) and install them: this will make your controller much more stable!
enjoy!
thingiverse
free
Comp 108 Micro Quad Frame by HalfAshby
...halfashby/designs
also, check out max's design for a camera mounting solution here: https://www.thingiverse.com/thing:2561423
thingiverse
free
Bugsy Jr, Micro Quadcopter, Baby 250 by PeculiarDesigns
... plate with a slight front notch for fpv view
11/25/17 - added feet! top plate hole for camera buttons.
11/24/17 - initial upload
thingiverse
free
Comp XL Micro Quad Frame by HalfAshby
...halfashby/designs
also, check out max's design for a camera mounting solution here: https://www.thingiverse.com/thing:2561423
thingiverse
free
Cheaper and easier, but still awesome speed tank by conquestdz
...the bec on one esc is this happens to you. i had no problem with the receiver linked above but your experience may be different.
thingiverse
free
Crossfire 2 by MikeyB
... not planning on having a camera or vibration dampening battery tray you can now strap your battery directly to the bottom plate.
grabcad
free
Quadcopter
...torcraft, as opposed to fixed-wing aircraft, because their lift is generated by a set of rotors (vertically oriented propellers).
grabcad
free
3d Printable Quadcopter
...rtically oriented propellers).
3d printable design suitable for abs/pla. about 42.71 gram weight for abs material.
size : 66x69
grabcad
free
WT-Quadcop
... the quad by the front or rear and peeling the feet from the load in unison. alternatively, we'll beef it up at a later date.