thingiverse

free

Nozzle for flex hose by Zh4x0r

...or flex hose by zh4x0r thingiverse the flex hose was awesome and printed very easily, so i created this nozzle to go along with!

thingiverse

free

Flex Pipe Nozzle Cooler (K8200) by mx5

...ton tape ). also the extruded filament seems to be cooled much better than with the standard 40mm fan+nozzle which i used before.

thingiverse

free

Aquarium Fluval Flex Nozzle/Flow/Extension/Düse/Verlängerung by RocketDave

...for the fluval flex basins, they must be scaled to 60%, the parts fit better if you print each extension and nozzle individually.

thingiverse

free

Flex Pipe Nozzle Cooler (Radial Fan Attachment) by PER_Design_and_Editing

...ng the two things linked above. mx5: http://www.thingiverse.com/mx5/about original thing: http://www.thingiverse.com/thing:282111

thingiverse

free

Bose soundlink mini cover (flex/tpu)

...(flex/tpu) thingiverse printed i n flex filament.135c for the nozzle 60c in bed printing speed 30mm/s with support...

thingiverse

free

RJ45 protector connector

...rj45 connector male print it in flex with a nozzle size...

thingiverse

free

Nokia c6-01 case by evgenykovtun63

...c6-01 case by evgenykovtun63 thingiverse material: petg (flex better) nozzle 0.4 puts on very...

thingiverse

free

Fogger interface for Gardena nozzle by ouf

...interface for gardena nozzle by ouf thingiverse pla and flex more details on...

thingiverse

free

iphone 5 case by sezurachaos

...iphone 5 case by sezurachaos thingiverse flex, nozzle diameter 0.5 mm, speed 45mm/s, retract 3, no...

thingiverse

free

Flex Adapter CR-10 by Mc_KaNaN

...adapter without wire adapter parameters for print: infill: 100% nozzle 0.4 velocity:...

thingiverse

free

E3D Box Insert by Sputnick

...comes with the nozzle fun pack. can hold 15 nozzle and some wrenches. while the edge of the box...

thingiverse

free

Mesh experiment 3(b), refined spheremesh by fluidity

...printing. note that the cups are set for double nozzle diameter thickness and are modified for only one nozzle...

thingiverse

free

Fila flex by Dant3C0rp

...adapter mk8. this part directs correctly the filaflex to nozzle hole. without this part, sometimes the fillaflex is pressed...

thingiverse

free

Ultimaker 2 Feeder Holder with anti-vibration flex parts by XylenC4

...um2 feeder holder with anti-vibration parts. easy printable without dual-nozzle ...

thingiverse

free

Door Knob Bumper by QuantumFlexGate

...with flex filament. i used sainsmart tpu at 220c nozzle temp and 50c print...

thingiverse

free

2020 Nozzle Holder

...frame, store your nozzles. recommend material : petg, because flexng good...

thingiverse

free

Flex Fan for Maker Select v2

...happens and the nozzle gets trashed, just print the nozzle instructions: requires the blower type fan print one each...

thingiverse

free

Ubiquiti UVC G3 Flex Shell

...wall thickness is 1.2mm so i used a 0.4mm nozzle at 100% infill. the top part and the cover...

thingiverse

free

Dice 2x2x2 cm by oleg31337

...filiament. tested with pla, abs, flex, wood and hips. nozzle sizes of 0.3 to...

thingiverse

free

Jet boat speedboat mod by mistyk

...mod add servo flex connector add gouvernail fixed on nozzle screw at the...

thingiverse

free

Sandblaster_Coke_Bottle by Shuffla

...one time i used wet sand and clogged the nozzle don't use wet sand...

thingiverse

free

Convoy C8+ Bumper

...print in tpu 100% infill. printed with a 0.4 nozzle on a 0.2 resolution. i used extrudr flex medium...

thingiverse

free

Mobula 7 1s battery holder

...flying with single 1s battery. im using a tpu, nozzle 0.4mm and layer 0.2mm. its easy print. no suports...

thingiverse

free

Huawei mate 10 pro case

...first (inner part, red): tpu (flex) bed = 55 nozzle = 230 no supports infill 5~15% second(outer part, black):...

thingiverse

free

hanger, towel hook in the nursery

...file include. printed on the printer tevo little monster, nozzle 1 mm, height 0.2 i make parts to order,...

thingiverse

free

Nozzle Wrench by 3D_ThingKing

...resistant co-polyester i printed the wheel handle with ninja flex it´s of course optional trouble fitting it in the...

thingiverse

free

Gleaner/Agco series 3 flex header tear drop bat reel bearing by Jason_WI

...printed these out of esun pa nylon at 260c nozzle temp and 110c bed temp. i use a printdry...

thingiverse

free

Sipeed MAIX-II Dock by juani_cer

...thingiverse case for sipeed maix-ii dock. printed with 0.2mm nozzle 0.12 layer height without support. the button pusher parts...

thingiverse

free

Samsung T3 Stand by jremar

...a samsung t3 external ssd. i used a 0.3mm nozzle but 0.4mm should work fine too, as the little...

thingiverse

free

Hypercube E3D mount with BLtouch by ziemowitp

...x_probe_offset_from_extruder 30 // x offset: -left +right [of the nozzle y_probe_offset_from_extruder 15 // y offset: -front +behind [the nozzle]...

thingiverse

free

Watering Can Nozzle by Caipi

...is around 22mm diameter. it's best printed with tpu flex material so it will be tight around the can's...

thingiverse

free

Nissan Titan Center Cap by ASD

...part that flexes better for install. i used 0.6mm nozzle 2 perimeter, 0.20 layer, 20% infill....

thingiverse

free

Blow Out Bulb by Flex_Wheel

...on. after the project was complete i added a nozzle to the chamber bulb and it become a handy...

thingiverse

free

Adjustable-Tilt X Carriage for Double Extruders on MakerFarm Prusa i3v by clough42

...be tilted left and right to level dual extruder nozzle. this plate will work with both the itty bitty...

thingiverse

free

Cable Holder Prusa i3 by benisjamn

...no retraction high heat bed high heat to extruder nozzle slow speed. 3 other designs not yet tested, but...

thingiverse

free

Ubiquiti UVC G3 Flex Shell

...thick so i can print it with a 0.4mm nozzle at 100%...

thingiverse

free

Flat Nozzle for Kobalt 24v blower by agibson2

...the thickness is only 0.8mm so that it will flex and doesn't break as easily and as a bonus...

thingiverse

free

Water drain pipe cap, diameter 192mm by deltapenguin

...time was 3 hours 15 min with 0.8 mm nozzle e3d volcano. the green plates made out of rubber...

thingiverse

free

Parametric Allit Europlus Flex Insert by fblumenberg

...to 0.8mm which means, two perimeters with a 0.4mm nozzle added the stl files for the most common...

thingiverse

free

Anet A6 Flex Filament Guide - improved derivate by Berlin_Engineer

...the old version on my extruder. i'm using different nozzle with a more extended thread. they cause that the...

thingiverse

free

Minimal Raspberry Pi camera holder for flex pipe

...of a minute or two. designed for a 0.4mm nozzle fdm printer. probably works with m2 screws, but i...

thingiverse

free

6mm Airsoft bullet shells for Revolver (max. 3 joules) by Mardari

...printed with pla flex (flexible filament) at a 0.4mm nozzle see shooting video here: https://youtu.be/ihgvua7iwos (another shooting video): https://www.youtube.com/watch?v=d_z6hxhxq6q...

thingiverse

free

Hexagonal flexible coaster by fluidity

...and fine layers, i recommend layers 1/6'th of your nozzle thickness and there's some bridging so put the actual...

thingiverse

free

M12 O-ring (Common 510 Vape/Vaporizer Component)

...axis (only!) to 85-90% works fine with a 0.4 nozzle even better with something...

thingiverse

free

iPhone 8 bumper case for flex filament by thingivinz

...it would print good without. used 40% infill, 0.4 nozzle and 0.2 layer...

thingiverse

free

3 Inch Ducted CineWhoop by Dkroes

...flex. i printed with 3 walls on a 0.6mm nozzle ...

thingiverse

free

FridayFPV Seeker Air-Unit Antenna & GPS Mount (TPU) V1.00 by DaveFridayJones

...get over the aluminium standoffs. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

Lee Die Locking Ring Wrench by Distal

...with 75% infill with 8 walls on a 0.40mm nozzle perhaps too much infill, but i was trying to...

thingiverse

free

GTECH Wheel Widget by MaJaDev

...when you try to print on hot plastic. 0.4mm nozzle beter definition and cooling but the tabs are not...

thingiverse

free

FridayFPV Seeker SMA Video Antenna Mount V1.00 by DaveFridayJones

...tpu or similar flex material. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

Underslung X Endstop for extreme X travel (MakerFarm i3v) by clough42

...further to the right. this allows the left extruder nozzle on dual extruder setups to reach more of the...

thingiverse

free

Mercury / Mariner Inflatable Pump Nozzle by Renba

...... at least one ring must be printed in flex material if possible.. feel free to combine other rings...

thingiverse

free

martian 2 SE fpv cam holder tpu

...8lines at least. i personally printed with a 0.2mm nozzle to reduce weight and 15%infill. original fpv cam support...

thingiverse

free

Kossel 2020 flex printed roller by Ferretti

...make delta printer inacurate. ps: print settings e3d 0.4 nozzle 0.15 layer height, 4 perimeters, 100% infill speed...

thingiverse

free

Zesty Nimble Smart Effector mount by RGN01

...horizontal movement will be transferred to the heatsink and nozzle through the nimble, pcb, heatsink, nozzle chain the nozzle...

thingiverse

free

MBN12H G5 Precision Piezo Grove mount X-carriage

...attach blowers to it, ziptie your cables to it... nozzle size1 is good for mosquito nozzle size-long is too...

thingiverse

free

FridayFPV Seeker Air-Unit Antenna Mount V1.00 by DaveFridayJones

...get over the aluminium standoffs. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

FridayFPV Seeker Arm Savers V1.00 by DaveFridayJones

...tpu or similar flex material. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

FridayFPV Seeker TBS Immortal Antenna Mount by DaveFridayJones

...tpu or similar flex material. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

Hypercube Titan Aero V6 and Vulcano Direct Drive Extruder for Flex Mount by butchja

...and vulcano hotends to this thing without changing the nozzle height. just use mounting holes marked with i for...

thingiverse

free

Wall Mounted Cup Holder With Hook for Glasses/Adaptable Sizes by Andrewtf

...about 20-30 minutes on my robo with the .6mm nozzle i would imagine a .4mm or .2mm would take...

thingiverse

free

E3D Heatsink 40mm fan assembly (model3) by WalterSKW

...stay nicely in place. print settings used : 0,6mm nozzle 0,32mm layers, support needed (but not that much) i've...

thingiverse

free

Screw organizer by Sica

...print at 0.2 mm layer height with 0.4 mm nozzle the lid is very thin in order to flex...

thingiverse

free

Flex Curtain Tie by bugman_140

...i printed them on my cr-10 with a 0,6mm nozzle with 100% infill and they took just under an...

thingiverse

free

Soft Top Roof for the Axial Wraith by 3D_ThingKing

...thin at places so i went for the 0.2 nozzle i think you can get by with 0.4 if...

thingiverse

free

Super UBQ 200 by stickboy1998

...the arms for airflow. currently printing with a 0.6mm nozzle ...

thingiverse

free

Rocket for Playmobil

...shell is 0.8 mm, so with a 0.4 mm nozzle this will be 2 shells. try to set the...

thingiverse

free

Cable Tie (flex) by dd_

...base construction is kind of bold. scaling for 0.4 nozzle is 2/3, tried that and it printed great (the...

thingiverse

free

Lightweight 5015 blower bracket and duct by GregValiant

...duct to keep the airflow off the nozzle. the nozzle can be removed with the duct in place. the...

thingiverse

free

ScubaPro MK10 SPEC boot

...just much easier to make. used flex pla. 0.4 nozzle 0.2 layer height, 0.36 line width, 100% infill, 220c...

thingiverse

free

Alphabet 28mm Miniatures by trumpoot

...a few of the letters did not print well (nozzle was knocking off top "suspended" portion of letter. for...

thingiverse

free

Strap keeper for Whoop strap v3

...for printing on a fdm printer with a 0.4mm nozzle which should result in two walls. fits a little...

thingiverse

free

1.75MM filliament Wade's Reloaded Extended height Hexagon Mount Extruder by piercet

...the carriage mount structure, which eliminates front to back nozzle flex. without this taller mount, a stock taz toolhead...

thingiverse

free

Earguard minimal by JohnnyB_make_me

...skirt single layer or none 0,3mm layer height 0,4mm nozzle ~<200mm lenght of object - 200mm bed lenght required...

thingiverse

free

protective cover for the engraver (Hammer Flex Md135a) by bomonets

...you can try to print it. printer: anycubic mega-s nozzle diameter: 0.4 layer height: 0.2 infill:...

thingiverse

free

xk x100 bigger battery mount / stand by fdev31

...it in abs at 0.2mm height with a 0.4mm nozzle it's just enough flex and...

thingiverse

free

Replicator Thermometer/Humidity Meter Clip by garyacrowellsr

...back, using the cutout that is/was/maybe intended for a nozzle wiper. updated: 6/24/12 the original was too 'bouncy'. it's...

thingiverse

free

No nonsense part cooler for FT5 Titan Volcano BLTouch combination by WalterSKW

...nozzles to get a more equal airflow through both nozzle. cleaned up/streamlined the initial model a bit, changed the...

thingiverse

free

Flex Filament Direct Drive Extruder (Max Micron and other Prusa i3's ) by Thomllama

...side. about 18% support coverage. use at least 3 nozzle widths for shell and at least 1mm top/bottom layering....

thingiverse

free

Larva-X Prop Guard by Alexsym

...join. no screws required. approx 13.5g. printed with 0.4mm nozzle in pla on a texured bed. the fit between...

thingiverse

free

Caliburn Shock Buffer by kitsune109

...in tpu or similar flex filament. 4-5 perimeters (.4 nozzle1.6-2.0mm wall) 20-25% infill should provide the right amount of...

thingiverse

free

Concrete lamp shade mold (compatible with Ikea HEMMA) by VaseyXXI

...thingiverse all files designed for 2 perimeters with 0.4mm nozzle printing. print two outer mold parts. print inner part...

thingiverse

free

E3D Heatsink 40mm fan assembly by WalterSKW

...printed in abs (next one will be in pc) nozzle 0,6mm, layer 0,32, support needed. i've printed it with...

thingiverse

free

Trucks for Z-18 Penny Skateboard by ColorFabb

...increase the layer cross section. we used a 0.8mm nozzle the trucks have been printed in colorfabb_ht, on the...

thingiverse

free

Creality Dual Extruder by daoguey

...i wanted to do was to put a dual nozzle (extruder) into the creality cr-10 in order to print...

thingiverse

free

UMD Memory Stick holder by thelongrunsmoke

...with pla, hips or sbs. layer height: 0.2 mm. nozzle 0.3-0.6 mm. if you print smaller or larger than...

thingiverse

free

fidget cube with flexible hinges by schuetzi99

...they are printed together to prevent moving under the nozzle while printing. update 2 i stake this is the...

thingiverse

free

RoadLok Seal Cap by PlasmaStar

...in flexiblem tpu drucken und montieren :-) print/druck parameter: nozzledüse: 215 °c bed/bett: 55 °c adhesion/haftung:...

thingiverse

free

Gopro 9 Lens Cap by ErikLtz

...flat side down and no support - standard 0.4 nozzle and 0.2 layer height works...

thingiverse

free

Flaco Pod Micro Cam by jr555se

...sides with cutter :) will redo this later.. 0.4 nozzle and flex is recommended. lumenier axii will fit but...

thingiverse

free

Flex USB / SD folding cover cap for Artillery Sidewinder X1 / Genius by Strat0

...logo doesn't come out too nicely with a 0.4 nozzle i added a "no-logo"...

thingiverse

free

2020 Alum frame snap on feet by Thomllama

...as top & bottom. infill at 25-40% (depending on nozzle size and which flex material you use) i found...

thingiverse

free

Upbox+ extruder mod for TPU UPBOX / Afinia H800 by jros

...dia ,i used the original bearing , drilled the nozzle out to 1mm .i cut an area out of...

thingiverse

free

FridayFPV Seeker DJI Airunit Mount V1.00 by DaveFridayJones

...tpu or similar flex material. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

Hubelino / Duplo compatible marble run items by advancedvb

...some flex tracks, which works fine. using: pla; 0.8 nozzle 0.2mm layer height. version 7 is flexible from design...

thingiverse

free

xDrip Wireless Bridge case v1.7 by Lehaiver

...tape on yours hotbed.) print settings: 0.10 layer, 0.3 nozzle 0.33 extr.width, 2 perimeters. added a cad file (solidworks2013)...

thingiverse

free

Anycubic Mega S extruder TPU Flex mod by ez_diy_technics

...gear will damage the filament, when it reach the nozzle at high movement speed and it will not print),...

thingiverse

free

LIAM diy robot lawn mower wheel accessories by Plastmartin

...no need for glue. pla and 10-15% infill, 0.4mm nozzle works great for me. included tires for liam original...

thingiverse

free

Two Up Head 90 Deg Relocator by 13DjjC13

...amount of flexing in the frame and causes the nozzle to "sway" in the y axis. this mod also...

thingiverse

free

e3d Titan Aero mount for Raise3d N2 by DenTwan

...circuit board for a duet wifi and changed the nozzle to a titan aero from e3d. you need 4...

thingiverse

free

FridayFPV Slate HD Camera Wedge V1.0 by DaveFridayJones

...tpu or similar flex material. optimised for a 0.4mm nozzle most parts of the print are completely filled with...

thingiverse

free

3D Pen Holder by 1bigpig

...points of contact, while allowing adequate airflow around the nozzle it will keep the heat transfer from the pen...

thingiverse

free

Bad day for a snowspeeder at Hoth by Hatsyflatsy

...the uploaded files. this was printed with a 0.3 nozzle and 0.2 layer. can be more detailed when printing...

thingiverse

free

FlexRC Ascent - Starpower Bodykit by ACROBORG

...thicknesses were designed around use of a .4mm print nozzle star-shaped window for wicked cooling. spoiler adds five horsepower....

thingiverse

free

Flex Hose (Revisited) by BrainFever

...flexible hose. i have also included models for a nozzle and a 40mm fan adapter, besides the normal tubing...

thingiverse

free

Flex Wallet by DinosaurNothlit

...while printing. i tended to get banding from the nozzle dragging on the filament as it was printing, so...

thingiverse

free

Titan X-carriage with piezo Z-probe by AikenJG

...half and almost eliminated vibration artefacts, both because the nozzle is now so much closer to the pivot point....

thingiverse

free

Zip or Cable Tie (Reusable) by PuterPro

...and is pretty cheap for a flex. print settings: nozzle .4mm line width .4mm layer .25mm (most people use...

thingiverse

free

Pfaff 262 Motor coupler by Pointy

...petg, no supports. .28 layer height for my .4 nozzle little cleanup around the edges. snapped into place. go...

thingiverse

free

Floss 2.1 Fin by jr555se

...i beefed it abit. printed with flex and 0.4 nozzle ...

thingiverse

free

Adjustable Y Axis Linear Bushing / Mount by roadkill6702

...at 0.2 mm layer height with a 0.4 mm nozzle 7/19/2017 - uploaded just the bushing section, for people...

thingiverse

free

Shaper Origin Vacuum Hose Strain Relief by aubie47

...a dual extrusion machine that had abs in one nozzle and tpu in the other. i created a second...

thingiverse

free

Precision Piezo Z-Sense Mount for Prusa/Anet v2 by pyr0ball

...to sense, therefore there's no x/y offsets if swapping nozzle, or using a modular print head, the z-sensor is...

thingiverse

free

kitchen wire rack clip by peter120

...up in petg for better mechanical flex strength. 0.4mm nozzle first layer thickness .4mm using a 4mm wide brim,...

thingiverse

free

Reverse mounting bracket for Sera Flore CO2 Reactor for Aquariums by barontechnologies

...have to mount a co2 reactor with the inlet nozzle pointing left. the mounting equipment that comes with the...

thingiverse

free

iMac G3 Power Button replacement by blkhawk

...small parts you will need a special small .2 nozzle to successfully print it. petg is also a requirement...

thingiverse

free

Half inch hose clamp

...ceiling. printed on a lulzbot mini with a .4mm nozzle with innofill3d abs fusion+. the abs is flexible enough...

thingiverse

free

Flexible Dust Collector for Drill (Eurohals)

...drill/cnc machine with an eurohals neck (diameter 43mm). the nozzle section is made of flexible segments that allow to...

thingiverse

free

Pen Screwdriver T3 by mikeprusa

...low-speed and for pla with max cooling. cura engine, nozzle 0,5mm, layer 0,25mm for p1, layer 0,2mm for p2...

thingiverse

free

LCD Panel stand and folding cover by saturdayxiii

...still some problems. i held my spatula beneath the nozzle in a couple places and it worked well...