thingiverse

free

Prusa i3 X End Motor for leadscrews by hackermagnet

...motor mount from the first prusa i3 rework. on the other side use the x_end_idler and x_belt_stretcher from prusa i3 rework 1.5

thingiverse

free

E3D V6 mount for Prusa I3 Rework by NeK6683

...d and then 4 m3x12 to attach e3d to extruder body. print speed: 50 layer height: 0.1 fill: 20% top, bottom and shell thickness: 1

thingiverse

free

Prusa i3 Handle for 8mm Frame by Phelps3D

...ount on a prusa i3 rework frame that was a 8 mm wide. it uses 4, 1/4 inch bolts and nuts. i would print at 50% or higher infill.

thingiverse

free

Proximity sensor mount for i3 Rework E3D Extruder v2 by FDMTech

...-4-z/bx sensor with this thing. the previous mount from korri wasn't low enough to hold it and have it sense the build plate.

thingiverse

free

Mounting plate for Bondtech Mini extruder/E3D v6 on i3/Rework/Wilson carriage by benvonhandorf

...tter. added a new m3 hole for fan mounting added a mount to the e3d clip to allow fan mounting added a fan mount design for above

thingiverse

free

Prusa i3 Rework ATX PSU Mount by Phelps3D

...file atx psu holder is a combined part, i broke it up because i was having problems with it printing in abs without delamination.

thingiverse

free

GoPro 1/4" Ball Joint to 1/2" Rod Mount by cptskippy

...can easily be changed via variables in the .scad file. if there's enough interest i might make rework it for the customizer.

thingiverse

free

J-Head Mount and clamp for Direct drive extruder by Techno35

...ect drive extruder so i reworked this thing extruder mount for direct drive. 4/30/2016 uploaded the new repaired j head mount.stl

thingiverse

free

Mini Talon Sunnysky 2216 replacement motor mount

... it to sink them in all the way. this is a lot better than any of the smaller mounts, and this one's holes line up perfectly!

thingiverse

free

Proximity sensor mount for i3 Rework E3D Extruder v3 by FDMTech

...-4-z/bx sensor with this thing. the previous mount from korri wasn't low enough to hold it and have it sense the build plate.

thingiverse

free

Wade Extruder Body Sensor mod for 1.75mm filament with support by bzhmaddog

...robe) #define x_probe_offset_from_extruder 0 #define y_probe_offset_from_extruder 25 #define z_probe_offset_from_extruder 0

thingiverse

free

NeXT Computer - Raspberry Pi 4 Case by XPlusE

...ded the front panel remix by bluebrews to this thing and a remix of the front panel without any holes for leds that i did myself.

thingiverse

free

Pentachoron Electronics/Base Exhaust for 60mm fan by Balmung83

...nd t-nuts to mount the exhaust to the extrusions. mount it inside the base. update 2018-07-13: reworked thing, lowered file-size.

thingiverse

free

Beaglebone Black with 4D LCD Display Case by quito___79

...he clear space for input/output cables. only need 4 m3x12 screw to fix all together, the case, the cover and even the beaglebone.

thingiverse

free

Prusa i3 Z Axis Stabilizer for board mount by mprobot

...crews into the board that the printer is mounted on. requires one 5/16" x 36" rod cut in half, 8 nuts, and 4 screws.

thingiverse

free

Prusa i3 Rework 1.5 (Emotion-Tech / reprap france) - Y belt tensioner system (complete) by bebenlebricolo

...may not slip away of the bearing's outer surface. mounting procedure is a bit less simple though, requires to...

thingiverse

free

GoPro mount for LG G3 holder by Lowfiero

...rework my lg g3 holder just a little(the center mounting hole had to be changed but both still work...

thingiverse

free

E3D Titan Mount (Wilson/Prusa i3 Rework) by cfunseth

...for the e3d titan extruder and wilson ts x-carriage mounting style (similar to the prusa i3 rework). i wasn't...

thingiverse

free

E3D Chimera/Cyclope Prusa i3 Rework Mount Bracket v2 Extended by invent0r

...ors, etc...) please like/collect if you are downloading, thank you. previous version: http://www.thingiverse.com/thing:661185

thingiverse

free

Folger Prusa i3 Overhead Spool Mount & Filament Guide Inspired by http://www.thingiverse.com/thing:786514 by kb3lnn

... it more stable. i can not print just yet waiting on printer to arrive. :) i used designspark mechanical to do the edit / rework.

thingiverse

free

Heavy Duty E3D V6 mount remix for Tronxy XY-2

...g was updated for 40x20 size; 4) also, it's cool idea to use guard for front fan (https://www.thingiverse.com/thing:1662879).

thingiverse

free

MP Select Mini 75mm VESA Mount (for Pi case) by j4c3

...j4c3 thingiverse 9/3/2016 update: i reworked the frames and mounting bracket. there is more space between the parts, so...

thingiverse

free

Lumia 1020 to Jobi Gorillapod Adapter by Protonite

...hread. might need some slight rework for a perfect fit, but nothing a knife/scalpel can't handle (depending on your printer).

thingiverse

free

CharlStruder For E3D and J-Head on Prusa i3 by DIYElectronics

...bearings, extruder springs, gregs wade style gears etc. two mounting options, standard prusa i3 x carriage and new prusa...

thingiverse

free

MicroDelta Rework Mounting Bracket/Spacer for E3D Titan Extruder by krizzli

...#39;ll also need to invert the motor direction by adding an exclamation mark to the value like so: extruder.hotend.dir_pin 0.4!

thingiverse

free

Hypercube X carriage with i3 rework compatible mount by pivan

...by arturslab (capitve nut locks). my contribution: redefined the mounting holes to be compatible with prusa i3 rework (m4...

thingiverse

free

MiniZ Feuerwehr-Truck Body 1:28 by ChrisPV

...u'll need 4 3x5mm magnets to hold the body and two small screws https://www.youtube.com/watch?v=cv-rfwyy4tm&feature=share

thingiverse

free

i3 Rework with e3d v6 hot end mount tight fit by 3ducate

... a slightly smaller piece to lock the hot end in. the current one works but you may need to trim it a little to for the snug fit.

thingiverse

free

E3D v6 mount with Inductive Sensor by o0aaron0o

...pe: npn voltage range dc6-36v output current: 300ma dimensions: m12x10x55mm detection distance: 4 mm output status: normally open

thingiverse

free

Geeetech A10 Z-axis optical endstop activator

...ctivator is to low and the activator does not pass the photo sensor in the middle. so i reworked the activator to fit for my a10.

thingiverse

free

DRO mount for Emco Unimat 3/4, MJ-189 mini lathe by drayson

...liper is well seated and the caps have a tight fit. use the clamping screw of the caliper to mount it to the carriage driver arm.

thingiverse

free

Raspberry Pi Camera Mount for TAZ 4/5 by Wolfie

...use of fisheye lenses.cameramountbaseforarm and cameramountarm: these are for mounting other cameras to the bed.camerafrontbottomwithlens: this is a modified...

thingiverse

free

Raspberry Pi 3 Hybrid Slim Case by kuhnibaert

...the ports. in addition i wanted to have various mounting options. you have a flat bottom surface so that...

thingiverse

free

AR Grip Action Cam Mount

...he standard 1/4" x 20 screw to attach the grip i designed it for an m4 screw and nut because that's what was on my desk.

thingiverse

free

L-Band Helical Antenna 12 Turns (RCHP) by Die_Bastelkammer

...antenna i used a 10x10mm aluminium tube. the helical mounting arms are a print part. antenna mount is the...

thingiverse

free

Fanatec Clubsport Formula magnetic shifter

...each side), 16mm m3 screws to mount part 2 and 10 or 12mm m3 to mount part 1. i printed everything without supports, worked fine.

thingiverse

free

Malyan M150 DiiiCooler mount by dunkwho

...clear of all 4 corners of the block. when mounting the cooler to the printer with this bracket i...

thingiverse

free

Titan extruder mount for lulzbot taz4 and taz5, one fan by Suntorn

... bed clamps but its rare this happens and isn't fixable yet. i will fix this when i recieve my new fan and rework the design.

thingiverse

free

Cable Chain Mount by m3lvm

...l need m2 screws 4 x 5mm m3 screws 4 x 10mm i used computer case blanking plate screws m3 nut and bolt 40mm cable strain relief.

thingiverse

free

Bulldog Lite Extruder, eBay E3D clone heatsink and Heatbed fan mount by friarfish

...er e3d heatsink. you can look at my photo and just count the number of fins. whats next? an add-on for a inductive sensor pickup

thingiverse

free

I3 rework upgrades and improvements by djvdpant

...quot;chamber.http://www.ikea.com/nl/nl/catalog/products/s69873735/ i designed the parts in freecad. http://www.freecadweb.org/

thingiverse

free

Ormerod 2 Adapter to fit a Nimble V1 by ZestyTech

...uder you can buy, it has ample torque and can be mounted in multiple orientations. the nimble is available from zesty technology.

thingiverse

free

FLSUN i3 Y Rod Mount Rework by lembasbrot

...lvaged from original mount) 8x m4x10mm 8x m4 square nuts 4x m3x20mm or 16mm 4x m3 nuts please use washers under the m4 bolts ;-)

thingiverse

free

Frame Stabilizer for Prusa i3 Hephestos XL by DemonCalcifer

...e m10 gewindestange. muss / kann mit etwas schleifpapier ausgeschliffen werden damit die stange leichter durch geht... viel spaß!

thingiverse

free

Inline Duet Filament Monitor Mount to 2020 by JoePogo

...t https://www.filastruder.com/collections/e3d-spare-parts-and-accessories/products/bowden-couplings-all-types?variant=21286000324

thingiverse

free

Prusa Rework X-Carriage for LM8LUU by GiulianoM

...ck, and insert one of the m3 screws through the loop to secure it. repeat the same for the other side, and then tension the belt.

thingiverse

free

Fan Mount by mc1457

...less turbulence. the fan mount is a fresh redesign, mounting along the x-axis. the duct is adjustable up and...

thingiverse

free

AM8 Reworked Electronics Case For RAMPS 1.4, Dual MOSFET & Fan by Thorinair

...m5*10 screws. houses a ramps 1.4 board, uses 3 mounting holes. high enough to house a full graphics display...

thingiverse

free

Itty Bitty Dual Extruder Mount for RepRap Wilson TS/II, Prusa i3 rework by unknown_lamer

...versions. i was able to countersink the holes for mounting the x-shelf of the extruder and have them overlap...

thingiverse

free

Cable Chain kit with shower hose (kit passa cavi con tubo doccia) by uLca by uLca

...;s raccomanded to leave into the hose a spare string/wire that could be usefull to pass inside some wires in case of maintenance.

thingiverse

free

Direct Drive Extruder MK8 by squareoctopus

...4 x 16mm hex-head screw 4 m4 x 20mm screw 1 m4 x 30mm screw 2 m4 x 12mm countersunk-head screw 1 compression spring 1 604 bearing

thingiverse

free

Easy 3D Printable CNC Drawing Machine (rework) by carl1961

...re https://github.com/blomsd/mpcnc-tft35-v2.0https://forum.v1engineering.com/t/mpcnc-build-complete-until-my-next-good-idea/11936

thingiverse

free

Raspberry Pi Zero W Case + Camera and mount for Replicator 1 / FlashForge Creator Pro / PowerSpec by dfoles

...redesigned the camera attaching area. still working on that part. i added just the case bottom with no mounts for other projects.

thingiverse

free

Reworked Shaft Encolsures by Dbakardj

...reworked shaft encolsures by dbakardj thingiverse the shaft snap-in mounting points were way too tight when printed. they all...

thingiverse

free

2-3-4-5-Owl - Ridged Y Carriage for Mendel and Prusa by BensHacks

...over the original frog design: it utilizes all 5 mounting holes of the heatbed to achieve maximum stiffens for...

thingiverse

free

15+ WRX Left Defrost Vent AP Mount

...ure and "fondle free") let me know if there is anything you might want to add or improve and i will see what i can do.

thingiverse

free

Heavy Duty Y Axis for Wilson II by lowfat

...16mm and an m3 nut. you can use a 16t idler or a pair of f693zz bearings for the tensioner. the motor mount screws are m3 x 14mm.

thingiverse

free

3018 Pro CNC Z-Axis Tool Adapters

... i go along. this is a full rework of a couple of designs found on thingiverse, mostly: https://www.thingiverse.com/thing:2880671

thingiverse

free

3DFused linear Bondtech BMG bracket for KLEMCO groovemount (rework) by deprecated

... torsional strength. revision 4 is optimized for 100% infill, while revision 3 will do fine with ~40% infill (gyroid works well).

thingiverse

free

8 port keystone mount for DIN rail. by ClintonRH

...needed to be. also the tab to release it from the rail broke. v2 should addresses these issues but i have not printed or used it.

thingiverse

free

FPV cam mount for china quadcopter X525-V3 by hastla

...fit much better. if you enhance or rework this design please add me as source that i can follow too my first design, thanks :-)

thingiverse

free

E3D Hemera Ender 3 mount/adapter by DenkBrettl

...modifications. things you will need: 4 x original hemera mounting screws if you're using the bltouch: 2 x m3x10...

thingiverse

free

FPV Racer Frame (~200 Doubledecker) Quadrocopter by headsho111

...top there is enough space for the battery. a mounting place for a cam is there as well. the...

thingiverse

free

Prusa I3 Rework Bowden Extruder and Carriage with Inductive Sensor by chinzw

...ing of the distance to the hotend. update 6: added a new version of the carriage clamp that adds a 40mm fan shroud for the e3d v6

thingiverse

free

Flexible Components for Sneaks Mount system by XboxOldie

...e flexibility with the ff-join, see pictures uploaded in addition. the print was done with a 4mm rim and support on the bed only.

thingiverse

free

60mm fan mount for Ramps board by turfstuf

...ore 3d than being 4 hours into a print job and closely watching/hoping for the last 10 minutes to not wreck the entire print job?

thingiverse

free

FLEX MOUNT : E3D TITAN : BLTOUCH | HYPERCUBE by PurchenZuPoden

...mounting plate: e3d_traeger_v2 [new] mounting plate for cooling fan: mountingplate_fan_v3 [new] mooling nozzle: cooling_nozzle_v2 [new] (this part needs to...

thingiverse

free

Ender 5 Direct Drive BGM-E3D v6 X-Axis Linear Rail for Hero Me MS by Obeahmon

...the design i made the contact faces for the mounting plate all planar and squared off the upper rounded...

thingiverse

free

Ecto Goggles Lens Plate

...rts as i put indentations for the lens bases to set into. this setup will help you align the holes to drill into the lens mounts.

thingiverse

free

Herringbone Prusa i3 Reworked Greg's Extruder by Godvalve

...threads when accessing the hobbed bolt. 6) a secondary mounting point was added at the back of the j-head...

thingiverse

free

X5S MGN12H Linear X & Y-axis with modular hotend mount

...it's made without a hotend mount, but has several mounting holes and big venting holes to accommodate good air...

thingiverse

free

Remix of DIY battery powered power supply

...v-slot. i redrew it in fusion 360 & added mounting bracket to match my project. i reoriented the display...

thingiverse

free

High Tech Windshield Ice Removal System by Fixerdave

... new thing called ‘winter’ sorry, i can't test it... started raining today :) (yes, first post on thingiverse, just testing)

thingiverse

free

Belt redesign for FT5 Revision 2 (X-Y idlers) by WalterSKW

...ulley that fits better with the y-endstop 20170816 - added 3mm x support tip : use 3d-tool to have a detailed look on this thing

thingiverse

free

Case for Electronic Load Battery Capacitor Tester found on eBay by MSpencer

...he pcb 3) mount the 4mm jacks (10mm hole already in there) and solder the wires 4) plug in the 12v power jack and start using it.

thingiverse

free

Reprapdiscount Full Graphic Smart LCD Controller Case by phil_from_seattle

...screw and nut 2 m5x10 screws and t-nuts for mounting on the rail. i've included the sketchup file. i...

thingiverse

free

I3 Rework single frame parametric Z axis stabalizer with Solidworks 2014 source by DarkAlchemist

... of the stuff i needed locally. i have added an easier access to the 3mm nuts upper piece in both stl and solidworks 2014 source.

thingiverse

free

e3d v6 adapter for Monoprice Select Mini V1 by mverive

...an shroud and air director updated 7/19/17 - enlarged mounting holes for sinking screw heads, improved alignment, and modified...

thingiverse

free

RepRap Delta Rostock Mini Pro 2 by gammarostock

...includes a filament-holder on top of the printer direct mounting at carriage of open belt-ends with zip-ties (with belt_mount_for_carriage.scad)...

thingiverse

free

X55 X56 HOTAS Desk Clamp remix v3 by jcarlin

...here is the link: https://www.amazon.com/gp/product/b07bhxxr4d/ref=ppx_yo_dt_b_asin_image_o08_s00?ie=utf8&psc=1 wali c-clamp base stand mounting accessory for wali monitor mount workstation system (c-clamp), black...

thingiverse

free

Yihua 8786D accessories by vaxxi

... nozzles (that's how many spares i have), a bit more compact and the nozzle holders are conical so they auto-adjust a little.

thingiverse

free

EVE 2.0 65mm by Rygar1432

...guard. added some space for both the front and rear props at the back edge. also made the supports stronger at the center spines.

thingiverse

free

E3D V6 Geetech Prusa i3 Mount by landie

...was a much better print than the second so you might end up having to print this twice, using the first print to cool the second.

thingiverse

free

Ultimaker Original Plus with E3D v6, dual fan, and BLTouch print head by GenCab

...ightly but the original can be found herehttps://www.youmagine.com/designs/compact-mount-for-e3d-v6-hot-end-on-ultimaker-original

thingiverse

free

Hot shoe torch mount for camera by simo9905

...e battery without unmount the whole body. incresed the size of the tensioner so now the screw doesn't collide with the mount.

thingiverse

free

wall box by d23elt05a

...a quick change system two small boxes for wall mounting designed with freecad. the screw holes are designed for...

thingiverse

free

Thumbhole Foregrip by BlasterCore

...the caliburn that replaces the standard grip rather than mounting to it, should help relieve stress on the stroke...

thingiverse

free

Metal Max adapter for the Nimble V1.1 by ZestyTech

...uder you can buy, it has ample torque and can be mounted in multiple orientations. the nimble is available from zesty technology.

thingiverse

free

Arduino controlled toy robot - 3d printable by Spelljammer

...stop the corners from curling. =========== update - rev 5 - separated the parts out and fixed a spot where the wheels rubbed.

thingiverse

free

CR-10 Heavy Duty customisable modular e3D V6 mount Volcano 5015 ABL by chito

...supports (needs new body) created new body with better mounting to x-carriage and updated wing rails new part: 30mm...

thingiverse

free

P3steel 2.x - X-axis complete by toolson

....11: z-endstop triggers are now mk2 version (short and long version available) please share your makes! http://scheuten.me/?p=441

thingiverse

free

Upgrade Prusa i3 (Rework) to MK2 by FDMTech

...that work with your current m10 all-thread/threaded rod. y-belt-guide-10mm-upgrade-rework-to-prusa-mk2.stl mounting though hole size was enlarged to 11mm to fit...

thingiverse

free

Bowden E3D V6 Mount For Geeetech Prusa i3 Pro B by landie

...was a much better print than the second so you might end up having to print this twice, using the first print to cool the second.

thingiverse

free

E3D Chimera Mount Ender 3

...lease improve on my design! again, didn't put a lot of effort in. let me know if you have any issues and i'll try to help

thingiverse

free

Lambda Shuttle by acmbarber

...to 1:270, cut a pie-shaped hole to accept a mounting peg pretty easy to assemble, at least compared to...

thingiverse

free

Creality CR6-SE V6 Mount Kit by jeremiahburt23

...i am not a trained cad designer, so if you find a way to improve on my frankenstein designs, please do so and share your results!

thingiverse

free

U.S.S. Defiant Warp Core by mkauffman41

...th higher resolution versions, deleting the low polygon ones. they are bigger files, but will require less post process clean up.

thingiverse

free

Modular Base for Raspberry Pi 3/Zero and Arduino Uno/Mega by aguzinski

...low for more variable use, and prevent having to junk the part if they break refined connecting peg to better hold parts together

thingiverse

free

Eachine CVATAR CineWhoop replacements Duct/DuctFeet/GoPro-/Antenna holder by ms2kTV

...y time spend on this design feel free to tip me but only if you can spare some and it will not affect your monthly living budget.

thingiverse

free

1" x 8 TPI faceplates for 80mm chucks

...3 hole faceplate v2.stl - provides a faceplate for mounting an 80mm chuck that has 3 mounting holes and...

thingiverse

free

HEVO / HPCE / PrecisionPIezo universal piezo Z probe adapter by Pumpal

...adapter by pumpal thingiverse i saw this idea for mounting a piezo for the precisionpiezo z probe and reworked...

thingiverse

free

DJI Phantom 135mm Leg Extension by H5Labs

...et, it hits the ground going over 100 miles per hour and leaves a small crater. mantis claw - www.thingiverse.com/thing:1659427.

thingiverse

free

MK8 -MK9 Support with autolevel 18mm version 2 by vniclos

...iage with high holes, by joe558, published jan 20, 2016 on this url, (for make coherence)http://www.thingiverse.com/thing:1281787

thingiverse

free

Eclips3DTitan gantry with BLTouch holder by sveske

...sult, so we can get the best gantry at the end :-) made for the http://www.eclips3d.com/ look out for upgrades :-) regards jesper

thingiverse

free

Anet A6 360W Upgrade PSU Cover by AB123D

...which i purchased at banggood - https://www.banggood.com/wholesale-12v-30a-360w-switch-power-supply-driver-for-led-strip-light-display-220v110v-p-39987.html?rmmds=search&cur_warehouse=cn . utilised mounting adapter from here - https://www.thingiverse.com/thing:2667230 (thanks charl13). this has...

thingiverse

free

WeebTheAirsofter MK23/SSX23 triggerguard holster V3 RIGHT/ LEFT

...e made for people who don't want to run with the suppressor support also added a updated v1 holster adaptor with rotary mount

thingiverse

free

modular x-carriage - next level: MGN12 linear guide x-axis by PredatorJr

...e lowered by 4, better 8 mm (v5). used 4mm first and the extrusion hit the rear heated bed glass clamp. there was a gap of 2.5mm.

thingiverse

free

Bedside Raspberry Pi Console Case for 3.5" PiTFT by kevinkahn

...the previous version. the case now has provision for mounting either a pi2/3 or a pi0. to mount a...

thingiverse

free

Geeetech A30 w/ SKR1.4T Control Box Eliminator by bavery79

...exit the box. i've left most of the component mounting holes for auxiliary components (mosfets, 5v dc-dc power supply...

thingiverse

free

BMG Aero Direct Extruder Mount for Anycubic Mega (S) by Leoliss

...ed with bmgaero) and threaded brass inserts (4-5mm, about 10ps) also thanks to raptorhunter for bmg aero model used as reference.

thingiverse

free

3D Printer Mendel Type X1(X2) extruder/s by TRENDi77

...1 bowden type extruder with 50 mm offset for mounting holes. may use my lcd case - http://www.thingiverse.com/thing:743724 or...

thingiverse

free

Drone Frame H-type 220x250mm and 220x185mm by TRENDi77

...arms - for users of motors with only 16x16mm mounting holes it wasn`t a problem, but for those, that...

thingiverse

free

RepRap Electronics Assembly V2 - Modular Attempt by Maaarsl

...eter for fan control (optional) 1x switch (optional) just in case you're thinking in imperial units: 1 inch equals 25.4 mm :)

thingiverse

free

Customisable Prusa i3 MK2 Rambo / Controller case - BASE by slippyr4

...and the offset from the board edge to the mounting holes. there are two more parameters which are optional...

thingiverse

free

Customisable Prusa i3 MK2 Rambo / Controller case - DOOR by slippyr4

...and the offset from the board edge to the mounting holes. there are two more parameters which are optional...

thingiverse

free

Bitx40 enclosure REMIX by WB9BBC by wb9bbc

...lid by adding m3 hex nut (press-fit) cutouts and mounting holes. reworked the bitx40 case by: -added mounting holes...

thingiverse

free

Weed2all HYPERCUBE EVOLUTION REWORK by weed2all

...will mount ) ---this build uses hidden corners for mounting the 3030 aluminium frame together!--- for bed also used...

thingiverse

free

Z SYNC - TRONXY X5SA by VisiTor

...(i recommend half thread, so there’s less clearance when mounting the 20t pulleys) + 8 x washers + 2...

thingiverse

free

MK8 Inductive, Servo, and Blower for Prusa i3 by woodywong

...riage and also graber i3 if you enjoy and make one i would really appreciate you posting a make with pics! happy new year 2016!!!

thingiverse

free

hera reworked grip and stock by CravenPayne

...stock. -finally, insert 1/8 inch (3.175 mm) pins in to the holes marked with red circles. instructions provided by koobysnacks77