521 i3 idler 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
Shown 1 of
5 pages
thingiverse
free
i3 Y-idler by Voxvalve
...
my idler broke and i could not find any that would fit my geeetech i3 (wooden frame"
hope it can be of use to other people.
thingiverse
free
prusia i3 idler by ma77morris
...erse
i have a cheap prusia i3 ctc printer and i have coppied design for the idler/ belt tensioner as i couldnt find any on here.
thingiverse
free
wanhao i3 y idler bracket by petrus1450
...o i3 y idler bracket by petrus1450
thingiverse
simple bracket in order to correct the bad design of the y idler on the wanhao i3
thingiverse
free
Prusa i3 Y-End Idler by Draman
...prusa i3 y-end idler by draman
thingiverse
small y idler
thingiverse
free
GT2 Idler Pulley Geeetech Prusa I3 by AlekPet
...gt2 idler pulley geeetech prusa i3 by alekpet
thingiverse
gt2 idler pulley geeetech prusa i3
thingiverse
free
Reprap Prusa i3 Y-axis idler by Vr5fx
...reprap prusa i3 y-axis idler by vr5fx
thingiverse
y-axis idler holder for the reprap prusa i3.
thingiverse
free
Prusa I3 rework Y idler by electrokill
... idler by electrokill
thingiverse
hey folks,
here's my conversion for the y axis idler of a prusa i3
its for an 624 bearing
thingiverse
free
prusa i3 anet a8 y belt idler by semelle
...prusa i3 anet a8 y belt idler by semelle
thingiverse
prusa i3 anet a8 y belt idler
thingiverse
free
Prusa i3 Forte X End Idler
...rk - x end idler
features:
thick and resistant part
enhanced clamp system with screw and nuts
recommendations: 100% infill, abs
thingiverse
free
prusa I3 X idler end by ritaxiang
..., pro b and pro c which you can see here http://www.geeetech.com/unassembledgeeetech-i3-pro-c-dual-extruder-3d-printer-p-927.html
thingiverse
free
Prusa i3 Y idler by jbascones
...mproves the tension on y axis
material
m6 nut x 1
m6x15 screw x1
pulley gt2 with tread 5mm diameter
m2.5 nut x 1
m2.5x20 screw x1
thingiverse
free
i3 y-idler with tensioner by richard_j_m
...grated tensioner.
it was easier for me to just create the design from scratch although if requested i can do an openscad version.
thingiverse
free
prusa i3 Y idler with belt tightener. by liusega
...ith belt tightener. by liusega
thingiverse
prusa i3 y idler with belt tightener
m5x20 screw x1
m5 nut
m3x15 screw x1
m3 nut x1
thingiverse
free
prusa i3 anet a8 y belt idler fat by semelle
...prusa i3 anet a8 y belt idler fat by semelle
thingiverse
prusa i3 anet a8 y belt idler fat
thingiverse
free
Prusa i3 X-End Idler - Stronger Version by blomker
...prusa i3 x-end idler - stronger version by blomker
thingiverse
uses 624zz idler bearing
thingiverse
free
Replace the X-axis idler on your Prusa i3 by MindRealm
... (upgrading) the printed x-axis idler with bearings.
http://www.instructables.com/id/replace-the-x-axis-idler-on-your-prusa-i3/
thingiverse
free
X-idler X-motor for Prusa i3 50 mm by radus
...x-idler x-motor for prusa i3 50 mm by radus
thingiverse
x-idler x-motor for prusa i3 with 50 mm between rods.
thingiverse
free
Geeetech I3 Y axis idler pulley by mbridak
...geeetech i3 y axis idler pulley by mbridak
thingiverse
idler pulley for y axis. prevents belt from rubbing on metal bracket.
thingiverse
free
AnyCubic Prusa i3 X-Axis (Idler) by tmssngr
...anycubic prusa i3 x-axis (idler) by tmssngr
thingiverse
this is the x-axis part for the right side of the anycubic prusa i3.
thingiverse
free
Geeetech i3 idler with Bowden extruder holder by ronindev
...bowden extruder for my geeetech acrylic i3. the best way to mount extruder is on the idler place, so ptfe tube has minimal lenght
thingiverse
free
Prusa i3 Z Axis Idler by chinzw
...z axis mounts.
you need to print 2x shims, they interface the 5mm thread to the 8mm hole in the 608 bearings.
bom:
2x608 bearings
thingiverse
free
Geeetech prusa i3 x pro Y idler by sender86
...geeetech prusa i3 x pro y idler by sender86
thingiverse
y idler pulley for two 624 zz ball bearings
thingiverse
free
Y idler prusa i3 rework by Qjr
...y idler prusa i3 rework by qjr
thingiverse
required:
1xm8 + nut
1xm4 +nut
bearing 608
thingiverse
free
Prusa i3 Y-Idler by Jooxoe3i
... into a triangle, which exacerbates the movement/wobble of the one-point-mount idler
this variant tries to fix these two issues
thingiverse
free
Prusa I3 x end idler by chris33
...e person who is printed it for me. also i seen that there was a motor x end on here so there needed to be the other end at least
thingiverse
free
Sustitute for two 624ZZ Bearing on Prusa I3 Idler by gunny26
...2 x double 624zz bearings which are use on x- and y- axis idler sides in prusa i3 assembly. printed and built in, but not tested.
thingiverse
free
Prusa-I3 x-belt tensioner/idler by Jooxoe3i
...ighthand part of the x-axis assembly
so it is possible to retrofit the existing part of the x-assembly with the tensioner feature
thingiverse
free
Prusa i3 X-End Idler w/ Captive Nut by ryborg
...prusa i3 x-end idler w/ captive nut by ryborg
thingiverse
modified x-end idler with captive nut
thingiverse
free
Prusa i3 Pro B Idler Ctc by romeo20o6
...prusa i3 pro b idler ctc by romeo20o6
thingiverse
gezeichnet mit catia gedruck mit abs für prusa i3 pro b ctc
thingiverse
free
Prusa i3 x end idler with belt tightener by liusega
...nd idler with belt tightener by liusega
thingiverse
modified x end idler with belt tightener
for increase tension of x axis belt
thingiverse
free
Sunhokey Prusa I3 short Y Axis Idler by shackfu
...e on my y axis, so i shortended the idler holder.
my belttensioner is on the build table mount, so i dont needed it on the idler.
thingiverse
free
x-end motor idler for Prusa i3 with 45 mm bw rods by radus
...ler for prusa i3 with 45 mm bw rods by radus
thingiverse
x-end motor idler for prusa i3 with 45 mm between rods and m5-10mm nut
thingiverse
free
prusa i3 Zonestar P802N P802NA Y idler by namelessexile
...802na y idler by namelessexile
thingiverse
for prusa i3 zonestar p802n p802na
infill 20%
create by bunjatec
edit for p802n by me
thingiverse
free
Prusa i3 MMU2s Idler Improved Fastening by Andison
...ral re-homing procedures.
in this redesign of the original idler (r1) the two m3 square nuts are replaced by two m3 locking nuts.
thingiverse
free
Prusa I3 X-END-IDLER-MODIFIED with X-END-IDLER-TENSIONER by danroh
...ng, two m3x14mm nuts and two m3 bolts
the working area of the tensioner is about 5-6mm, it should be enough to tighten the belt
thingiverse
free
Prusa i3 Idler 20 teeth GT2 bearing by feinripper
...bearing mr74zz
with a optional spacer for m3 screws which is a bit tricky to print.
dimensions: 9mm wide, diameter 16mm, 20 teeth
thingiverse
free
Prusa i3 Rework 1.5 Double F624ZZ Y-Idler by timere969
...mere969
thingiverse
i readjusted the y-end idler to replace the original to allow to flanged bearings instead of the single one.
thingiverse
free
ANet A8 (Geetech) i3 X Belt Idler Pulley Carrier by Kirion
...ulley carrier by kirion
thingiverse
this is an idler pulley carrier for the x belt. to be used on the geetech metal upgrade kit.
thingiverse
free
Prusa i3 Y IDLER Replacement Tensioner by BilboX
...ion you want to apply.
i include the 123d sources if you like the concept and need to adapt is to your printer.
hope you like it.
thingiverse
free
Prusa i3 y axis idler with M3 bolt tensioner by 3DPRINTERSSHOP
...prusa i3 y axis idler with m3 bolt tensioner by 3dprintersshop
thingiverse
not necessary to unassembly any part.
thingiverse
free
Y idler for Prusa i3 Steel in OpenSCAD by Professional3D
...bearing configuration.
if you make this thing i would like to see it! upload a photo of your print with "i made one".
thingiverse
free
Prusa i3 Rework - Y-idler 60mm / Reverse edition by FDMTech
...ed rods.
updated files. fixed some issues with reverse edition. both have gone through model repair service and came out great.
thingiverse
free
Prusa i3 Mk2 Idler Redesign by stephanbrunker
...pied the design and moved the ball bearing 1 mm lower, it is now exactly on the same height than the extruder axis (the red one).
thingiverse
free
Prusa i3 Rework 1.5 Double F624ZZ X-Idler by timere969
...ginal to allow to flanged bearings instead of the single one. i was having a problem with rubbing and this nipped it in the bud.
thingiverse
free
Cocoon Create Touch / Wanhao i3 Plus Y axis idler brace by martin_au
...the aluminium type idlers. it should just slip on over the top of the idler, but you may have to undo one of the lcd bolts first.
thingiverse
free
Compact Prusa i3 Y Idler by NorthernLayers
...o make sure its stays put.
enjoy, feedback/suggestions always appreciated.
released through my company: http://northernlayers.com
thingiverse
free
Prusa i3 X-End Idler by Draman
...read) , 1 x 20 mm cross screw (m4 + nut) and 1 x 40 mm m5 screw
update:
the bearing is an mf105zz 5 x 10 x 4 mm! 2 needed!!!!
thingiverse
free
dual 608 bearing idler for i3 - 10mm rod remix by curious_pl
...dual 608 bearing idler for i3 - 10mm rod remix by curious_pl
thingiverse
remixed to fit 10mm rod.
also a bit fatter nut holder.
thingiverse
free
X-motor&idler for Prusa i3 rework for 6mm threaded rod by Alex_Post
...lex_post
thingiverse
this is version of the elements of the x-axis for 6 mm threaded rods and nuts 6mm printer prusa i3 rework.
thingiverse
free
Y-axis belt idler and tensioner Prusa I3, CoreXY with FreeCAD files by omega776
...xis belt idler and tensioner prusa i3, corexy with freecad files by omega776
thingiverse
designed to be printed with no support.
thingiverse
free
Prusa i3 MK2 x-end idler and motor, resized nut by tomasjuri
...usa3d/original-prusa-i3/tree/mk2/printed-parts/scad
assembly instructions: http://manual.prusa3d.com/guide/3.+x-axis+assembly/105
thingiverse
free
Prusa i3 rework fixed idler by jrhuerta
...thought to be used with some tensioner on the bed belt holder.
you will need an m6 screw with a nylon nut and a couple of mf126zz
thingiverse
free
Toothed idler fork A8 I3 for Randinos mounts
...ngiverse that fit the bill, so i whipped this up in ds mechanical real quick. credit goes to randino as i based it on his design.
thingiverse
free
Wanhao i3 Y-axis idler pulley bracket by leaftye
...
this is a remix of: https://www.thingiverse.com/thing:1532408
it's significantly beefed up to allow for higher belt tension.
thingiverse
free
Spacer to adjust extruder idler for Prusa i3 MK2(S) by RonaTV
... slicer to shrink or expand the spacer according to your targeted value.
you can let the part in place for printing or remove it.
thingiverse
free
Duplicator i3 front y-axis idler by GreyDay
...ide the piece on to the frame.
attach the screws.
attach the belt and idler.
reattach the front part of the frame to the printer.
thingiverse
free
prusa i3 rework t8 idler remix by dgately
...s", so his designs could change and this re-mix would need an update as well.
thanks to phil_maddox for such a great design!
thingiverse
free
I3 Mk2/MK2s Extruder Idler with Push fitting Support for filament guide by crynool
...ified version of the original scad file from prusa, i did not print it, so i'm not sure if this works with the push fitting.
thingiverse
free
Scroll wheel for extruder idler for Prusa i3 MK2(S) by RonaTV
...to avoid the use of the allen key. it is quicker for me.
you need m3x40 hex (iso4017) screws instead of the iso4762 m3x40 screws.
thingiverse
free
Sintron i3 X Axis End For Tension Idler by dl6lr
...tallation.
use a m5 nyloc nut and an 25mm m5 bolt with a 20teeth gt2 idler (18mm outer diameter, 9mm width, 5mm innder diameter).
thingiverse
free
Prusa I3 Y-idler Tensioner by nw15062
...625 bearings, and m3 screws, the m3 nuts should slide in fairly easily but this will place the belt level with the y-motor mount.
thingiverse
free
Prusa I3 X-end Idler w/ tensioner by rball716
...lide in place
no support necessary. print out my 25mm bridge test and as long as you can print that this will print no problem
thingiverse
free
Prusa Mendel I3 Rework extruder idler with lever by jroger
...t loading.
loading lever
to release spring pressure without hurting your fingers when engaging the filament into the extruder.
thingiverse
free
X end idler + end stop for prusa I3 Rev. 1.5 by dedlefou
...x end idler + end stop for prusa i3 rev. 1.5 by dedlefou
thingiverse
this one let you keep your end stop on right side.
thingiverse
free
Single Piecer Y end idler for PRUSA i3 by vvdd
...
thingiverse
modified for 8mm rods holes
added optional hole to lock the 8mm sliding shaft with 3mm screw
fixed all bad surfaces
thingiverse
free
prusa i3 rework 1.5 Y belt idler update by mazkagaz
...ue-libre ).
as for the x belt stretcher, you'll have to print the y_belt_idler_2 part twice, one for each side of the pulley.
thingiverse
free
Prusa i3 X-Axis Motor Drive and Idler assemblies by Kannonballer
...ll.
i have included modified an extruder mount and shroud assembly to fit on the x-carriage of the twelvepro i3 printer system.
thingiverse
free
Original Prusa i3 MK3 624 bearing idler door by mcm001
...4 bearing, and operates similar to the mk2/mk2s's idler. i've attached a stl and sldprt in case you need to customize it.
thingiverse
free
Improved Y idler bracket with spring tensioner for FLSUN i3 by nuhv
...cket screw
m5 wing nut
m3 locking nut
2pc m5x9.5 washers
spring (i reused one of the bed adjustment springs from the printer kit)
thingiverse
free
Y-axis idler - Edited for - Geeetech i3 pro c printer by hlevy
...3 pro c printer by hlevy
thingiverse
i took the design of jooxoe3i and changed it a bit to fit..
fixes the problem of the belt..
thingiverse
free
Prusa i3 MK3 623h bearing housing (X/Y idler) by Papiertuete
...;s the same for the x-axis.
i think a part like this definitely doesn't have to be out of metal; it's just an idler... :)
thingiverse
free
X carrige belt idler for GEEETech prusa i3 x by sender86
...x by sender86
thingiverse
this is belt tensioning for x axies if pulley bearing fails. i designed it around two 624 zz bearings.
thingiverse
free
Maker Select Plus / Wanhao Duplicator i3 Plus Y Idler by cambunch
...led. m3 nuts fit securely into the bracket. the stock hardware for the idler itself can be used for installation on this bracket.
thingiverse
free
MakersDR Prusa i3 2020 Y Belt Idler by cjj25
...ral sizing here: https://cad.onshape.com/documents/4b7ab860bb33be5cda9e54c0/w/1d3d2cb7491f21f2fc70f8e6/e/5f682381cad0546d69e35b9d
thingiverse
free
Belt guide for 624zz bearing for Prusa I3 X - Y idlers by juliohcd
... tight and broke to assemble. they have 4mm inner diameter and have been tested so they don't collide with the idler bracket.
thingiverse
free
Idler/Pulley Replacement for Geeetech Prusa i3 X by datdiy
...ingiverse.com/thing:1818674
update2: version with ball bearings and teeth for gt2 belts https://www.thingiverse.com/thing:2002345
thingiverse
free
Dual 608 bearing Y idler for Prusa i3 -Remix Reinforced. by norm8332
...ing, so it has been reinforced and also the bolt hole was slightly enlarged because it was too tight when i printed it using abs.
thingiverse
free
Prusa i3 Rework Y Idler w/Tension knob by lockezio
...ction in your motion than you want. use a drop of thread locker and tighten until their is 1 to 2 threads coming out of the nut.
thingiverse
free
Aurora prusa I3 Y idler tensioner by JMBishop
...es a larger m6 screw, a m6 nut and a locking m6 nut for a solid tensioner. it may be over engineered but should be easier to use.
thingiverse
free
Dual bearing y-axis belt idler for Prusa i3. by WebClaw
...ine with x2 washers to reduce friction.
both high and low bearing mount versions are included along with source sketchup files.
thingiverse
free
12 mm diameter Pulley for x-axis idler Prusa I3 with FreeCAD files by omega776
...verse.com/thing:1215991. i also use this part with y-axis belt idler and tensioner. the ball bearing diameter is 9 mm, i use two.
thingiverse
free
Prusa i3 MK2S X-axis adjustable idler by steelydev
...inate that black dust that used to be your belt. i printed mine in white abs just to be sure to see any dust. so far, so clean.
thingiverse
free
Prusa i3 x-axis Idler with Tensioner by iridesand
...lt in any way. i am using mechanical endstops, so it does not have provisions for the optical endstops like the part it replaces.
thingiverse
free
Wanhao i3 Y Axis idler upgrade and belt tensioner by The_Monstro
...h bolt (corrected)
x2 m5x15 (i recommed inner hex bolts)
x2 m5 nuts with nylon
x1 m6 wide washer
x1 m6 thumb nut
happy upgrading!
thingiverse
free
Prusa i3 EiNSTEiN - X end idler, with filled side by xcoder
...tightening the belt bearing. so i decided to fill it, and it did improve the strength. at least i can properly strengthen it now.
thingiverse
free
x-idler remake for Original Prusa i3 MK2S by lukaspl
...t no space between the screw head and the rod of the z axis.
do not forget to do the xyz calibration after you changed the idler!
thingiverse
free
Wanhao i3 X - idler upgrade by The_Monstro
...n bolt so that it would screw in a nut in a plate part.
13) now tighten the ordinary nut to metal bracket (away from idler)
done!
thingiverse
free
Prusa i3 adjustable Y idler *for m8 bolt* by Sailor96
...much better fitting
update:
larger hole for an easier fit, also.2 supports instead of large gap where it connects to the base
thingiverse
free
Duplicator i3 y-axis idler assembly by tjlqk3
...ustment for belt tension.
this does require you to drill 3 holes in the frame, so do at your own risk. measure twice, drill once!
thingiverse
free
Belt Tensioner Prusia i3 (idler) by stphnbrd
... too small. but i have enlarged them now. if they need to be adjusted please let me know but they should be okay as they are now.
thingiverse
free
Prusa i3 Y end idler with tensioner (608 bearing) by aristos_v
...dit several parameters of the object.
i recommend using pla for better layer adhesion.
leave a "like" if it helped you!
thingiverse
free
i3 y-idler with tensioner - sturdy version by enlait
...ut 4mm wider and 5mm longer; however all mounting distances are the same. bearing bolt holes are no longer too close to the edge.
thingiverse
free
Direct Drive Prusa i3 idler remix by Podrez
...bb. also i have added 10mm m3 screw and some washer from piece of textolite which holds bb in place, and makes this thing sturdy.
thingiverse
free
Prusa style X idler and Motor Mount for Geeetech I3 printer by feedrate
...in difference is the offset between the z thread rod and z guide rod. on the geeetech they are aligned in y, and 27mm apart in x.
thingiverse
free
A better X Idler Tensioner for Prusa i3 mk3s by AWSb
...revised x-axis but make this even more rigid by using m5x20 screws. i suggest to the taurus x-axis motor mount for the left side.
thingiverse
free
Prusa I3 MK2 x-idler by blackbird2016
...e to process.
it is quite sturdy, no problems with adhesion at all.
and really nice and brilliant colours for a reasonable price.
thingiverse
free
Prusa i3 Rework - Y-Idler (625ZZ bearing) by punkrockseb
...int bed.
parts needed:
2x 625zz bearings
1x m5 screw
1x m5 nut
iges included for modification needs. everyone should do this.
thingiverse
free
Prusa i3 MK2S x-end-idler by GMagician
...etter belt move
little modification to x-end-idler anti-wobble
september 11th 2017:
new antiwobble, wrong measures on old version
thingiverse
free
Prusa i3 MK2 X-Idler Tensioner by Jasenk
... kit came with extras that i used.
the pully slide (x-end-idler-front-tensioner) fits one way. if it's tight flip it around.
thingiverse
free
X axis End PRUSA i3 Idler tensor with dock - Tensor correra eje X con muelle con by IngenioTriana3D
...ady tu insert in a tipical prusa i3 x axis / tensor de correa preparado para encajar en una pieza normal del eje x de la prusa i3
thingiverse
free
Dual 608 bearing Y idler for Prusa i3 by PristineSource
...08 bearings with a m8 bolt.
you will need:
1x m8x30mm cap screw
1x m8 lock nut
2x 608 bearings
2x m4x20mm cap screws
2x m4 nuts
thingiverse
free
Prusa i3 MK3 Clone x-end-motor and x-iend-idler for brass nut by heron
...y heron
thingiverse
the original mk3/s uses pom nuts on the leadscrews. this design works with the more common 22 mm brass nuts.
thingiverse
free
Dual 608 bearing Y idler for Prusa i3 with 10mm threaded rod by Tech2C
...-slightly reduced the bearing rim.
you will need:
1x m8x30mm cap screw
1x m8 nut
2x 608 bearings
2x m4x20mm cap screws
2x m4 nuts
thingiverse
free
623ZZ pulley for Prusa i3 X idler belt tensioner by AndrewBCN
...this avoids creating a seam on the perimeter of the pulley.
openscad sources are included so the design can be further remixed.
thingiverse
free
Prusa I3 Rework EXTRUDER-IDLER-with-thumb-guide-1.75-filament by DarkAlchemist
...arts i have are for 3mm and it leads to issues with the filament manipulation.
this is a wip so any issues let me know please. :)
thingiverse
free
Idler pulley bracket replacement for Geeetech i3 X by lukie80
...ing assembly easier. print with 100% infill for maximum strength.
in my case (geeetech acrylic) this is a obligatory replacement.
thingiverse
free
prusa I3 X idler end (for bearing from metal upgrade) by mrcory
... remove the lower holder for the bearing. this removes the need to cut it out after the print.
(forgive the terrible description)
thingiverse
free
Extruder idler V2.0 by mikon3
...thingiverse stronger thin section of extruder idler for prusa i3 ...
thingiverse
free
CTC i3 Clone X/Y axis belt pulley idler by matonym
...ded to possible be drilled for exact match. same with the long m3 bolt for belt tension.
the bearings for this thing is mf 85 zz.
thingiverse
free
Prusa i3 X Idler Tension modification/ 5mm Z screw by OgreMills
...s well, though isn't modified at all. uses 5mm threaded rod. m4 screws and nuts act as tensioning adjustment as well. enjoy!
thingiverse
free
Geeetech Prusa i3 - X and Y axis idler pulley with push pin by babokaj
...ctly.
http://www.thingiverse.com/thing:629381
i have been using the idler pulley for 50+ hours of printing time without problems.
thingiverse
free
Prusa I3 spring loaded idler extruder by chris33
... change the hole spacing my advise is go into freecad open the freecad file and go into the tree a and change the hole parameters
thingiverse
free
X-Idler for i3 for use with Leadscrew and 624 Bearing by ImpulsiveJames
...ses the leadscrew nut with 4 screw holes (i got mine from folger tech)
this was a hackjob, just fyi. i hope it works for someone.
thingiverse
free
Prusa i3 MK2 X Idler/Belt Tensioner+ v2 by IsmaelPR1
...and through the idler and secure with the tensioner round screw that will have the nut placed inside of it in the space provided.
thingiverse
free
Idler/Pulley Replacement with MR74ZZ ball bearings for Geeetech Prusa i3 X by datdiy
...ps://www.thingiverse.com/thing:1775944
edit 29.12.16: made a better version with teeth: https://www.thingiverse.com/thing:2002345
thingiverse
free
Prusa I3 Rework X-Idler Drop In Replacement Tensioner upgrade with Solidworks 2014 Source by DarkAlchemist
...out on you.
.
.
this is 5mm wider than the original as i added that to help reinforce it but can easily be removed in the source.
thingiverse
free
X or Y idler support by nigelbe
...an idler and tensioner for ctc diy kit prusa i3 clone bought from...
thingiverse
free
Geeetech Prusa I3 X Y Idler & Tensioner by ant0ny
...lt.
https://www.youtube.com/watch?v=pdiu9ghskdo
added idler to take mr84zz but i am unable to test this... may work as the other.
thingiverse
free
Prusa i3 X Axis X-Carrage and X-Idler With Bearing Stops by iPrintIn3D
...ed to revise the x axis carriages.
download this stl file and stop it for peace of mind and save money on half finished prints.
thingiverse
free
Prusa i3 Updated X-Axis Motor and Idler Ends - Remix by LionFox
...tor end
i printed one with pla and one with abs because i didn't want to get another spool... it should be fine in whatever.