23 hole ferrite 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Ferrite Rod 30x4mm PCB through hole holder by vernygora
...gora
thingiverse
a through hole pcb holder for a 30x4mm ferrite rod such as:
https://www.mouser.com/productdetail/623-3078990881
thingiverse
free
Choke/balun case for center fed dipole antenna
...center mount to secure the ferrite core, with 3 hole for zip ties m4 screws for the dipole wire...
thingiverse
free
Cord Holder with a magnet by truhlik_fredy
...cord holder with a magnet by truhlik_fredy thingiverse the hole for the magnet is 7.3 x 3mm so it...
thingiverse
free
TARDIS comming through a worm hole - Magnet by wavok
...material to use to glue in the 0.75"x0.1875" round ferrite magnet. simply cut the brim off, slide in the...
thingiverse
free
Power Jack inverter mounting bracket by sschm9
...printed the ones in the pictures, the m8 screw hole were slotted to allow for some adjustment if the...
thingiverse
free
Small Qi charger box by DonJuanito
...long guides and slide it towards the usb connector hole while pushing it down. it should slide easily and...
thingiverse
free
Brio compatible diesel engine by greyhawk01
...holes in diesel_base (use v2) increased diameter of pilot hole for furniture stud in brio_base_3ax (use v2) print the...
thingiverse
free
Bosch 360deg Camera Wall Corner Mount by Cr4shdummy
...bead of the cable. be very cautious while drilling hole at the wall edge, because otherwise it may happen...
thingiverse
free
Starlink Internet House entry by Humanshield1981
...clean up the install. based off of a 1" hole i used a spade bit. either an m3 nut...
thingiverse
free
OctoPrint disconnect fix (SerialException) by Mikael70
...greatly improved if you feed the cable through the hole many times but i think it’s not that practical....
thingiverse
free
3x3 inch magnetic planter w/ magnetic catch tray by Tory3DDesigns
...without the name tag slot, since the name tag hole leaves visible lines which might not be desired if...
thingiverse
free
Nintendo Switch Wall Stand / Shelf by daniel_489
...able to fall off the stand sideways. the screw hole are made for counter-sunk screws like for example dry-wall...
thingiverse
free
Perendev Magnet Motor by m4dscience
...there can give it a try. the rotor group hole should be .875 in diameter with 0.4375 spacings. this...
thingiverse
free
FlashForge Dreamer Thermostat Mount by BaronWilliams
...be difficult, and would eventually strip the plastic screw hole. i wanted a convenient way to install and remove...
thingiverse
free
ASUS XTION 3D scanner - Handle and Lens Cover by CreativeTools
...on the flat base surface of the grip the hole on the base make it easy to attach the...
thingiverse
free
Doublet-Isolators for 300 Ohm Twin Lead by DH1ND
...saw and file for iron). for centering, a 3mm hole is drilled at each end of the twin lead....
thingiverse
free
Raspberry Pi Zero W portable 18650 case - media player / streamer by rumina
...cap heat it up and stick it through the hole solder a cable to it. solder the battery connectors...
thingiverse
free
FlashForge 2016 LCD/SDCard/Keypad Interface Board Redesign by dewhisna
...with the lcd installed, making it possible to drill hole in the plastic lcd panel to access them. for...
thingiverse
free
Servo driven nozzle wiper arm by ProtomakerSprint
...likely not be suitable your 3d printer, the mounting hole and support arms are good for the hs 311...
grabcad
free
VIC Bobbins - Modular Designs for Ferrite U Core
...a 608 bearing in the other and align bearing hole with lathe point. i recommend making a metal insert...
grabcad
free
ASUS XTION 3D scanner - Handle and Lens Cover
...the flat base surface of the grip - the hole on the base make it easy to attach the...
cg_trader
$15
Voronoi Chess Set | 3D
...hollow bases, i suggest to not fully fill the hole with support material, because this is hard to remove....
3dwarehouse
free
Floppy 3.5' diskette
...on entry into the drive. rather than having a hole in the center, it has a metal hub which...