15 first c8 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Forrader/UltraFire C8 adapter for gBeam by willie42
...tube: i made it a bit longer, with the first shorter version, the "shadow" of the led was visible...
thingiverse
free
CELESTRON C8 XLT FOCUSER MOTORIZARION: by jmontsecal
...uppergearholder, and to disengage the motor for a rough first focusing, just pull out a bit the servosupport4motor, focus...
thingiverse
free
Duncan Mask for Celestron CPC8 by mr_milo
...mask i previously made out of foam sheets. i first saw the idea at: http://alpha-lyrae.co.uk/2013/12/31/schmitt-cassegrain-collimation-made-easy-using-a-duncan-mask/ i then made a...
thingiverse
free
Corvette Ute by petropixel
...a disguise being worn by new mid-engined corvette prototype http://www.caranddriver.com/news/exclusive-mid-engine-c8-chevrolet-corvette-firstphotos-news but it would make a pretty neat vehicle as-is....
thingiverse
free
Socket Enclosure for ESP266 Moes QS-WiFi-D01 150W Dimmer
...your connections! note: to set up the dimmer you first need to connect a switch to get it started...
thingiverse
free
"Mistral" Extruder Cooling Duct for the Anet A8 Printer by Leo_N
...your surroundings. this is how to calibrate the hotend: first we need to get the pid values from the...
thingiverse
free
Hotend and Heatbed PID Tuning - Gcode programs
...e0 s200 c8 u1; start hotend pid tunning - first hotend, temp: 200deg, 8 cycles. it takes some minutes,...
thingiverse
free
Simple ER11 drill vacuum 52mm turbine by maikll
...at maximum its difficult to stop it by hands first put bearing in holder after put it on shaft...
thingiverse
free
"Mistral 2.1" Extruder Cooling Duct for the Anet A8 Printer by Leo_N
...your surroundings. this is how to calibrate the hotend: first we need to get the pid values from the...
thingiverse
free
Pergo Robo3D Upgrade, NeoCeram Glass and 600 watt(110v) heater by Pergo
...is a 600 watt heater. when the heater is first turned on, and yes, it does take the stated...
thingiverse
free
Bolter Conversion for G36 Airsoft by xceptionzero
...raild1 - 4th part of rail section connector1 - first part of the upper rail section connector2 - 2nd...
thingiverse
free
Anet A6 - Autolevel bed sensor Blue SN-04N by d3adlydozen
...machine // start. when show_custom_bootscreen is defined marlin will first show your // custom boot image and then the...
grabcad
free
2019 Chevrolet Corvette C8 Stingray
...been “unlocked” for corvette which the creator of the first corvette had it in mind. now it is here....
grabcad
free
Coloana fara sfarsit (Endless Column) - Târgu Jiu, ROMANIA
...20 to 24 you can see brâncusi's masterpieces. the first time i made the model of the column was...
3dwarehouse
free
Chevrolet Corvette (C8)
...following several experimental cerv prototype vehicles, it is the first mid-engine corvette since the model's introduction in 1953 (as...