thingiverse

free

Extruder Screw/compression screw by tebeva87

... can be 3d printed and lost wax/pla cast to make a metal screw. it is mean to be used in a filament extruder or similar projects.

thingiverse

free

MK7 Spring Compressed Extruder - Heavy Duty by DrunkRabbit

...g parts. so i designed a heavy duty mk7 extruder. based off the exturder i found here (http://www.thingiverse.com/thing:245677)

thingiverse

free

Mendel Extruder w/Compression & No Epoxy by vik

...t screw, and a cutout allows one of the two m4x40 mounting screws a little more room so a washer can be used underneath its head.

thingiverse

free

2mm spring preload spacer for FlashForge Creator Pro extruders

...it to immediately start extruding again, so i made these 6.7mm diameter spacers that preload the springs with 2mm of compression.

thingiverse

free

Compact extruder for kossel mini by Miles_JD

...g and mk8 gear spring compression: 28x5.5mm / wire 0.8mm m3 screw in all hole m3 12mm screw with out head for bearing have fun :)

thingiverse

free

Creality direct BMG extruder MK-8 stock hotend mount

...t for creality-like machines (mk-10 hotend). p.s. i don't know why the thingiverse has been compressing images so much lately

thingiverse

free

Maker Select v2 Extruder Spring Riser 3mm

...ill compress the spring 3mm over stock to ensure deeper bite. tested out on duramic 3d petg filament. ymmv with softer filaments.

thingiverse

free

Hero Me Gen5 Creality Grey Upgrade Extruder Adapter by bad-geek

...ing instead of triangular as the stock extruder has, so i modified the opening to accommodate. it's a bit snug, but it works.

thingiverse

free

Bearing idler for M8 pinch wheel extruder by Spacexula

... for you to create your own version of an extruder. it took me hours to get everything lined up, hoping to save you the trouble.

thingiverse

free

direct extruder - mk7 gear - E3D v6 - 1.75 filament by raziber

...mm filament. very compact and easy to install. for filament compression adjust the screws in the oval holes. bearing used: 10x5x4

thingiverse

free

EZ3D Phoenix Extruder Lever by vandarin

...iginal phoenix design. if you've received your printer in the later part of 2014, use http://www.thingiverse.com/thing:609112

thingiverse

free

Deltaprintr lower extruder holder by johntron

...g surface to 9.4mm to fit a 1/8 bspp compression fitting. holes for screws countersunk an additional 0.75mm for total of 1.5mm.

thingiverse

free

RatRig V-Cast :: Z support bearing by WartyTowel

...the x rail can get very heavy with two extrudes etc. so i made a holder to fit a...

thingiverse

free

Extruder spring insert/spacer by akalomen76

...nal extruder spring as the aftermarket one was way stiffer and with the additional spacers on both ends became excessively stiff.

thingiverse

free

Quadcopter landing gear by austinreid

...landing. they also look cool. printed on a dual extrude flashforge....

thingiverse

free

Extruder mount, can be used for flex filament as well by SummersideGuy

...ar. well i added some extensions to prevent this and i also added a threaded end for easier installation of a compression fitting

thingiverse

free

Easy and efficient Z-axis anti backlash for Prusa i3 by JuTakata

...you are using a lightweight extruder like a bowden extrude. required parts (for each side): 1x m5 nut 1x...

thingiverse

free

Toggle Latch Extruder for 1.75mm MakerGear Groove Mount by DaleDunn

...also, i figured that even if they weren't fully compressed they would only tend to add variability to the...

thingiverse

free

CR-10S extruder spring helper by thatdude902

... the other end into the stationary part where the spring went before, and then push in the helper into place like in the picture.

thingiverse

free

Multoo MT1.5 single extruder base (E3D V6, flexible fiament and light hood mods) by NvigR8

...er out to allow more light down on the build surface. this is the single extruder version. there is also a dual extruder version.

thingiverse

free

Multoo MT1.5 dual extruder base (E3D V6, flexible fiament and light hood mods) by NvigR8

... out to allow more light down on the build surface. this is the dual extruder version. there is also a single extruder version.

thingiverse

free

TEVO Tornado anti-backlash feed tube spacer by rrehders

...and noticed that the compression fitting used at the extrude had about 1mm of play between the compression fitting...

thingiverse

free

Ender 3 and Ender 3 V2 extruder spring spacers/compressors by ReDaLeRt

...nsion for your particular needs. the fusion 360 file is attached, if needed to custom fit these spacers for your particular case.

thingiverse

free

Auger valve for clay by misan

... air is used to push clay to the valve. rotor needs an o-ring to seal it with the stator. first test https://youtu.be/3bslz789epq

thingiverse

free

MK10 Extruder spring pre-tensioner by L3WD

... this will work for other extruders of similar design if they use the same size spring, but i only have experience with the mk10.

thingiverse

free

Prusa i3 Direct Drive Extruder by blomker

...rking length = 19.9mm outside diameter = 7.3mm wire diameter = 1mm load at minimum working length = 34.13n spring rate = 3.26n/mm

thingiverse

free

BI Edition Extruder V1.0 (Bowden Type) by Boots_Industries

...uder failure when filament diameters varies. looking for pla? we offer unmatched 1.75 pla print quality with our sp series pla.

thingiverse

free

SN04 Z Adjuster Tevo Tarantula dual extruder by gkatin

...hing the aluminum structure, do not use the printer. see the photo showing the gap between the sensor and the aluminum structure.

thingiverse

free

'Flextruder' Malyan M200 Flexible Filament Extruder by JanBe

... the gear (marked yellow in the photo) you´ll need a 2mm (15mm long) rod or similar bolt and 3mm metric bolt + nut for the clamp.

thingiverse

free

Dasaki Compact Direct Drive Extruder MOD by naviathan

...e small top fin of the heatsink. i also added an 18mm mount to the tap for an induction sensor. i hope this helps others as well.

thingiverse

free

Flexion compressed air cooler by ahorn

...born as i upgraded my ctc with two flexion extrudes and my old cooling duct did not fit anymore...

thingiverse

free

RepRap X2V3 by dob71

...features: support independently moving x axis carriages for 2 extrudes; nozzle wiping/cleaning; frame modifications allowing x stage to move...

thingiverse

free

Extruder Calibration Aid Improved, for Prusa i3 by BManx2000

...cker. the screws are now configured as set screws, which loads them in compression rather than tension, so they should not break.

thingiverse

free

Printing with flexible filaments on the Creality Ender-3 and CR-10 by tom666

...1x mk8 drive gear 1x pc4-m6 fitting from stock extrude 1x 608zz bearing 1x m5x10mm half-round head screw 3x...

thingiverse

free

Yet Another Bowden Extruder by theFabFor

... the filament guide would be first in line. a fast release would be handy. could be much more compact. integral filament wiper...

thingiverse

free

Generic Bowden Extruder Upgrade for TPU/TPE by alexferreira1

...my first post and i couldn't figure out how to upload the photos without compressing them so any advice would be appreciated.

thingiverse

free

CR10 Max Direct drive extruder by Fugazi123

...ther two positions. i have created a smaller version to fit the right-front corner and the back-center. a m3-.50 nut is required.

thingiverse

free

CR10 Extruder Arm, Double Shear

...is design and make an update here. parameters: i'm printing with a raft, 100% infill, with support, 0.2mm layer height, pla.

thingiverse

free

Modified Extruder for Zortrax M200 by ArneBanane

...bearing has low backlash the holes, where the filament runs through have an optimal surface quality and the holes are not shifted

thingiverse

free

another customisable (not via customizer, though, ATM) bowden extruder for geared nema17 motor by hackele

...use spring 10mm in diameter 9.6mm long when fully compressed both are 1.75 filament. though there are many parameters...

thingiverse

free

K8200 Greg's Wade Extruder Mount by kauz

... print with reasonable infill (70% +). mounts with 2x m4x20 (extruder) and two 30mm long threaded rods and nuts to the printer z.

thingiverse

free

Ender 3/Pro Side Spool Mount - No extra hardare required by Gbartonw

...the spool can be placed centrally next to the extrude (rather than offset whcih leads to the fillamet entering...

thingiverse

free

Zortrax active cooling of extruder gear by DrewPetitclerc

...causing strip-out, so i added this mod to use compressed air to actively cool the gear, it works great...

thingiverse

free

Filament Load Lever - JGAurora A3 by JROBot

...head. back pressure on the forward screw of the extrude fan mount works well so as to not be...

thingiverse

free

Direct Drive Bowden Minimalist Extruder by blah_59

...w.thingiverse.com/thing:159478 it could also be mounted directly to an aluminum extrusion with appropriately sized t-slot nuts.

thingiverse

free

Nema 17 mounting by kenwshmt

...17 mounting by kenwshmt thingiverse printrbot / wades / extrude motor top attachment mount. this is the top arm...

thingiverse

free

Direct Drive Extruder MK8 by squareoctopus

...4 x 16mm hex-head screw 4 m4 x 20mm screw 1 m4 x 30mm screw 2 m4 x 12mm countersunk-head screw 1 compression spring 1 604 bearing

thingiverse

free

Printrbot Simple Extruder Fan Mount by JPoel

...not using) and the ground of the 5v e-stop connection. see photos for details. extruder runs cool to the touch during printing.

thingiverse

free

Cyborg Geared Extruder for 3030 Extrusion by brainchecker

...3 nuts and washers only part3 needs to be printed with supports. printed in petg with an high amount of infill for good strength.

thingiverse

free

Extruder Tension Control with Cable Guide by vivamus3d

...keep it cool i have no more issues with flexible/tpu filament. the tension control reuires a simple m5x10mm (knurled) screw + nut

thingiverse

free

Even more minimal MK7 extruder bearing filament feeder by joechung

...y compression. so this version does not have the quick change feature, but now only needs the 623 bearing and standard m3 screws.

thingiverse

free

Anet MK8 extruder filament guides

...filament guide don't have the stroke limitation. soft filament compressed much more, therefore the u-groove bearing must be able...

thingiverse

free

Gear Gap Filler and Softener by polymaker

...by polymaker thingiverse i finally decided to try greg's extrude (from the felt branch of prusamendel). the gears meshed...

thingiverse

free

Remix of Orbiter Extruder mount for Smart Effector by St233t

...well 68mm piece and of bowden tube for a compressed fit great work by lorinczroby on the orbiter can't...

thingiverse

free

Dial Indicator Holder for Artillery X1

...compress the probe. (3) press the indicator onto the extrude cooling...

thingiverse

free

MXL Belt Bowden Extruder 1.75mm by runninfarmer

...compress the filament enough. i used an aluminum gt2 pulley for the motor, but i've added a printable 20 tooth mxl pulley.

thingiverse

free

MAKERGEAR M2 EXTRUDER (REMIX OF BEN HECK'S DESIGN)

... seems to have enough spring force to allow the pinch arm to compress the filament to the motor for feeding through the extruder.

thingiverse

free

Car mounted phone holder (spring loaded) by bnardus

...the type of spring you would find in an extrude assembly or heated bed adjustment screw. the fully extended...

thingiverse

free

Original Desktop Filament Extruder E1.5 by ARTME 3D by ARTME3D

...e known, the extruder can be started in a few minutes. you can find empirical values ​​for the setting at www.artme-3d.de/support

thingiverse

free

Prusa i3 Nema17 Extruder Motor Heatsink Clamp by Revenson

...he heatsink. pictured are standard 40x40mm aluminum heatsinks with thermal adhesive: https://www.amazon.com/gp/product/b07d4fvc61

thingiverse

free

New material for flexy object extrude by happynew3d

... can find orange , red, green and transparent urethane 3mmhttp://youtu.be/xib0-scksyq share the knowledge ! have fun happynew3d

thingiverse

free

1" to 1.125" Threadless stem shim by aiber

...much better to just go in the sldprt & extrude it further, then remove the excess. do not just...

thingiverse

free

New BIBO Dual Extruder Drive Block Upgrade by jasonwt1977

...de of the extruder without taking it off the carriage. there is a spot for a captured m3 nut inside the tension adjustment area.

thingiverse

free

Bike Chain Fidget by kgreuel99

...after this sketch, i used the "extrude" tool and extrude the arms and inner circles 7mm. i then went...

thingiverse

free

Universal Filament Filter and Lubricator by CreativeTools

...the filament passing through gets lubricated, thus relieving the extrude motor from strain. lubrication is especially useful if the...

thingiverse

free

Extruder Tension Setting Gauge by davidhbrown

...to 9.5mm at which point my springs have completely compressed this is probably uselessly tight. i don't have any...

thingiverse

free

B2D Extruder - Strong and Silent Bowden Extruder by HeyVye

...stronger base plate. 20/09/2017 - fixed the bowden connector for 2.85 being too tight. adjustable tension for the v3 base plates.

thingiverse

free

Chocolate Cooler by Ioan

...for those of you who are using the chocolate extrude thing: http://www.thingiverse.com/thing:18017 because printed hot chocolate layers are to...

thingiverse

free

Greg's Hinged Accessible Extruder by GregFrost

... - add arcol (cory75 thing:10532) and wildseyed hotend mount options. im not overly happy with the asymmetry of the arcol option.

thingiverse

free

1306/1407 Motor SOFT mount TPU Vibration Dampeners by samms

...130% extrusion multiplier. tpu likes to compress and under extrude good luck. i'm also selling these in packs of...

thingiverse

free

Mk8 Filament/Feeder Cooler - 40mm Fan by dan0h

...of the stepper motor. easily installed over a mk8 extrude, and for the cr-10 in particular this acts as...

thingiverse

free

"Doubowden" Double Hobbed Bolt Bowden Extruder Assembly by MatGyver85

...pression springs for idlers. not sure what size exactly. 2 - 8mm x 15mm drill rod (5/16" may work) 1 - nema 17 stepper motor

thingiverse

free

Prusa 3 Dual Extruder upgrade kit by EMG

...with inventor are icluded to allow modifications in a compressed file. also the stls for direct print. (caution: some...

thingiverse

free

1,75mm lasercut extruder Bowden type by revolucion3D

... 22mm x 6mm (similar a los de la cama caliente )/ 22mm x 6 mm compression spring(heated bed alike) 1 x polea mk8 / mk8 drive gear

thingiverse

free

Geeetech Aluminium ZStop Extender by bernbout

...thingiverse had to order a throat for my mk8 extrude and got the 50mm one. since the original geetech...

thingiverse

free

Blower Fan Duct for Dual Extruder Cooling for Flashforge Inventor 3D Printer

...is allowed to flow down smoothly prior to being compressed at the bottom. the air path at the bottom...

thingiverse

free

Greg's Wade Accessible Belt Drive Extruder, Rev2 by pefozzy

... please let me know. -updated the solidworks part file- it now includes two configurations, the default 3mm and a 1.75mm version.

thingiverse

free

22xx TPU Motor Vibration Dampener by samms

...or something extrusion multiplier. tpu likes to compress and under-extrude good luck. i'm also selling these in packs of...

thingiverse

free

A direct drive bowden extruder for 3mm by depri51giu

... id • 2x m3x50mm head screw with suitable length for the selected spring • 2xplates aluminium 6x3x30mm with holes and threads

thingiverse

free

A direct drive bowden extruder for 1.75mm by depri51giu

... id • 2x m3x50mm head screw with suitable length for the selected spring • 2xplates aluminium 6x3x30mm with holes and threads

thingiverse

free

Rostock Max Extruder v2 by kitecraft

...block is closer to the lever providing a more compressed spring and increased pressure on filament. the filament entry...

thingiverse

free

FT5 Conversion Gantry by butterball_z

...style extruder that has a fan, then heatsink, then extrude, then motor, all held together with two long screws....

thingiverse

free

C.W.C Printer Bowden Extruder, direct drive 1.75mm,MK8 Gear by chiungweichen

...below: ~8.5mm outside diameter ~25mm uncompressed length ~14mm fully compressed ...

thingiverse

free

Bearing spool holder with adjustable brake by Jarek_P

...any compression spring with dimensions more/less similar to standard extrude spring, but with thinner wire, original is too hard....

thingiverse

free

Filament Oiler & Low Filament Alarm Accessories by MechEngineerMike

...on the engineerdog store or on amazon here: fittings: https://www.amazon.com/biqu-straight-pneumatic-connector-extrude/dp/b01ib81ihg/ref=as_li_ss_tl?ie=utf8&qid=1481488537&sr=8-1&keywords=bowden+tube+fitting+m10&linkcode=sl1&tag=engin09-20&linkid=95efe20d805e68093f2076cfd73d8b5e 4mm bowden tube: https://www.amazon.com/biqu-straight-pneumatic-connector-extruder/dp/b01ib81ihg/ref=as_li_ss_tl?ie=utf8&qid=1481488537&sr=8-1&keywords=bowden+tube+fitting+m10&linkcode=sl1&tag=engin09-20&linkid=95efe20d805e68093f2076cfd73d8b5e recommended oil: https://www.amazon.com/biqu-straight-pneumatic-connector-extruder/dp/b01ib81ihg/ref=as_li_ss_tl?ie=utf8&qid=1481488537&sr=8-1&keywords=bowden+tube+fitting+m10&linkcode=sl1&tag=engin09-20&linkid=95efe20d805e68093f2076cfd73d8b5e video link:...

thingiverse

free

Prusa Mini Copperhead Hotend Adapters by stegenga

...install steps additional hardware: ptfe tubing: length dependent on extrude attachment method 3mm hex nut for top of adapter...

thingiverse

free

2X Extruder Upgrade by JoeSoap583

... the springs, so it is feasible to add the bolt on the left side only if that's the extruder where you use problem filaments.

thingiverse

free

Spring loaded extruder for Leapfrog Creatr by Rob65

...not always enough so i moved the spring and compressed it a bit more resulting in more pressure on...

thingiverse

free

i3 Top Bearing Bracket by ADHDesigns

...rattled frequently (better than a screech though) when the extrude moved back and forward its weight caused the motor...

thingiverse

free

Replicator 2X Extruder Upgrade for Flexible Filament by mangojelly

...this is for the right extruder, you can simply mirror the stl files if needing an upgrade for the left extruder. happy printing!

thingiverse

free

Ultimaker Original Betterstruder by hackentosher

...apply more clamping force to the filament allowing the extrude to push harder. i have not tried printing this...

thingiverse

free

Bowden Extruder Pla 1.75mm Nema 17 MKS8 Gear by Generalx5

...the m3 screw, and to allow spring compression adjustment. one 12mm m3 screw with hex nut (for securing the spring loaded bearing)

thingiverse

free

Anet A8 Adjustable bearing holder for Igus Drylin bearings by StringyMcStringface

...this is very fiddly to get right so the extrude mount moves nice and loose. take your time. i...

thingiverse

free

Mechanical Blowfish by Vise

...tired yet because 3 days ago i broke my extrude, but i hope will work! ps: sorry, for the...

thingiverse

free

D-Bot Fully-Supported Extruder by dotorg

...d one on the right, so there's versions for either side uploaded. you only need to print the two parts for the side you want.

thingiverse

free

Manual Mesh Bed Leveling Test

...look like: https://youtu.be/rzry6kunavs?list=pli1fl66rf3erczp24wyta8kzqemsewncf&t=159 make also sure to tune your extrude e-steps and flow before using this test. the result...

thingiverse

free

Prusa i3 IPI rework by CraftMaker

...are arranged all over the printer. -universal and simple extrude mount. -reinforced averall structure. -clever structure for the x...

thingiverse

free

Direct Drive Bowden Minimalist Extruder 2.0 by blah_59

...w.thingiverse.com/thing:159478 it could also be mounted directly to an aluminum extrusion with appropriately sized t-slot nuts.

thingiverse

free

Shock absorber rubber by Wolraad

...allows flexible filament to be printed using a bowden extrude. printing speed is very slow. 1cm/s can be reached;...

thingiverse

free

Geared Bowden Extruder using Bondtech gears by gennro

...works for you. 1x pc4 - m6 coupler with 4.3mm bore nema 17 stepper motor 1x 40mm m5 hex head bolt 2x 695zz bearings 1x 1mm washer

thingiverse

free

Biqu H2 mount for Ender 3 with max print area by A-make-designs

...a mod to mount a biqu h2 direct drive extrude on an ender 3 without losing print volume. due...

thingiverse

free

Davinci E3D mount with extruder upgrade by scobo

...d through the hole in the top of the lever (see picture above.) you might need to drill the hole out a bit if it's too tight.

thingiverse

free

Odd Old Kenwood 3 pin plug by Desertbard

...plug by desertbard thingiverse print setting were for pla extrude 210 build plate 50. whatever you do, let it...

thingiverse

free

Citadels Classic Insert - Square box

...it is a tight fit, so if your printer over-extrude on corners you may have to sand or shrink...

thingiverse

free

Wanhao Duplicator I3 Bowden Extruder for E3D V6 ReFresh by Cinpro

...you can mount it with the logo facing out. the design that inspired this is found here: http://www.thingiverse.com/thing:1777358

thingiverse

free

HyperCube Dual - Upgrade pack by frabraha

...is an upgrade package to get dual hotends and extrudes. i'm still working on this, as my hypercube is...

thingiverse

free

Tevo Bearing/Rod Holder by Generalx5

...holder by generalx5 thingiverse used on standard 20mm wide extrude aluminum frames. this rod guide uses standard 608z bearings...

thingiverse

free

Wanhao i3/plus/whatever fits. Spoolholder with bearing! by EUCGUY

...version, even a heavy spool is easy for the extrude motor to pull. can easily be scaled up for...

thingiverse

free

Spring-loaded Replicator 1 Drive Block - Modified Lever by gyronictonic

...to push-fit the bearing in. this is the main extrude used for my reprap 3dprinter, 3dprintmihttp://www.thingiverse.com/thing:95339 parts: 1 x...

thingiverse

free

Geeetech i3 Pro X layer fan by viper2097

...directly mounted on the geeetech prusa i3 pro x extrude mount and a 40mm fan should be...

thingiverse

free

Screw/ Worm drive filament extruder Bowden by GadgetGuru314

...and i'll increase the bend radius in a bug fix. bug fixes: 180 degree filament curve added to help prevent filament twist.

thingiverse

free

PTFE M4 threading tool by spegelius

...broken ptfe couplers when doing multi-material printing with strong extrudes. but one thing has always been a bit cumbersome...

thingiverse

free

Ender 3 - Runout Sensor and Filament Guide Bracket by PaperGorilla

...bracket by papergorilla thingiverse this bracket attaches to the extrude motor plate using the two screws which hold the...

thingiverse

free

J head, Buda, and bowden adapters by blbergeson

...a plug will be needed for the recessed bottom extrudes. most of the pictures are of the aluminum variety...

thingiverse

free

Sovol SV01 Flexible Filament Funnel Replacement

...it's a direct replacement for the funnel on the extrude. remove the old one and replace with this one....

thingiverse

free

Noise Damper – Schalldämpfer für MK8 Extruderlüfter by Mardor

...disassembled the extruder unit you could take the chance and get rid of the loud original fan in favour of a better designed one.

thingiverse

free

da vinci EASY BED calibration remix for FlashForge by Sparky6548

...that if i wedge it with a bit of extrude filament, it works perfectly. not enough of a bother...

thingiverse

free

E3D Titan Extruder Upgrade for Prusa Steel Igus bearings by monnerby

...or bltouch holder and imuu8 bearings. update 2017-06-21 i use the fan holder from here: https://www.thingiverse.com/thing:1571526

thingiverse

free

Pegasus Pocket Powerbox Advance 2-inch bracket by CinciJeff

... fit a 3" leg. note that this 3" design has not been tested so if you make it, please let me know how it works. thanks!

thingiverse

free

Monoprice Wanhao Maker Select V2 Duplicator (clone) X-Gantry Brace

...right side bracket is smaller, to allow clearance for extrude motor modded cable routing. uses the 8mm bolt for...