15 extender ormerod 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Ormerod 2 X-motor bracket with extended Z-nut trap one piece by Le4fy
...ended z-nut trap one piece by le4fy
thingiverse
one piece x-motor bracket with extended and closed z-nut trap for the ormerod 2.
thingiverse
free
Extended Ormerod Z-nut trap by jstck
...and the stepper motor. this is the recommended one.
still oriented in the "odd angle" for printing without supports.
thingiverse
free
Easy Fit Extended Nozzle Mount for Ormerod 3D Printer by KimBrown
...e nozzle mounting screw holes and plenty of clearance around the bowden tube fitting, so no fighting to get it mounted.
enjoy....
thingiverse
free
1mm Extended Ormerod Nozzle Mount with Microswitch (2 Versions) by KimBrown
... the nozzle mount is extended by 1mm to suit some of the probes that are doing the rounds if you fancy switching between systems.
thingiverse
free
Amsterdamman's remix of Jstck's Extended Ormerod Z-nut trap by HandlaidTracks-3DprintedTrains
...rap was too loose. i opened the m5 nut trap wider and also removed the flare from the m3 nut trap and tightened it very slightly.
thingiverse
free
Ormerod Z spool by alexgibson
...t captures the z leadscrew and allows the spool to sit above the x carriage - especially useful on my extended ormerod - morerod.
thingiverse
free
Second cooling fan for Ormerod 2 by infoGenius
...cone and add a better mounting bracket. the duct should be angled away from the bed, when mounted, to give better bed clearnance.
thingiverse
free
Ormerod 75mm Diameter Extruder Drive Block by thowe
...nnel.
i also extended the support clip a bit where it clips over the x axis. i had experience of the original coming unclipped.
thingiverse
free
Ormerod X-idler bracket with belt tensioner by jstck
... issues, there is a second one (named "2") that is re-exported from a newer sketchup version which may be a bit better.
thingiverse
free
Ormerod 75mm Diameter Extruder Drive Block - 3.2mm feed by thowe
...ed.
i have also enlarged the feed pipe to 3.2mm diameter as i found the original diameter just slightly caught when i printed it.
thingiverse
free
Ormerod Z axis Top mount & M5 Bar top by ashsoft2000
...o use in place of the metal nut. the nut is a little tighter in the mount and so takes up the play. simply print more when worn.
thingiverse
free
Plate for RJ45 LAN extension receptacle by ZeAllan
...o instead hold the connector fixed to the outside of the box, running through a much less design critical hole beneath the plate.
thingiverse
free
PanelDue 7 inch display enclosure and mount by trevmas
...the cables are readily available as raspberry pi gpio extender. the disadvantage of this is that to access the...
thingiverse
free
Ormerod 2 Y axis mods by trevmas
...ame still sits on 3 points, i found a couple of layers of non slip under the front corners kept the whole machine nice and level.
thingiverse
free
Amsterdamman's Stabilized Z axis Herringbone Gear for Reprap Ormerod by HandlaidTracks-3DprintedTrains
...e and centers it on the threaded rod. i printed a m5 washer as well since i didn't have one here, but did have a 3d printer!!