17 e3d atx 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Hypercube Evolution (HEVO) E3D Hermes/Hemera with and without 24 Pin ATX connector
...://amzn.to/2rj5gwt
i think do you know that you have to insert one thread. i am using
ruthex m3 thread: https://amzn.to/384cefk
thingiverse
free
Printrbot Simple Metal Ubis 13s fan mount by ajcraig
...fan should be wired as shown in this guide. http://matterhackers.dozuki.com/guide/how+to+install+an+e3dv6+hotend+on+a+printrbot+simple+metal/9 ...
thingiverse
free
Power supply cover and power button housing for MakerFarm Prusa i3 by matador
...and the other fits the grub screw on my e3d ...
thingiverse
free
Airtripper bowden for E3D V6 Kit with Bowden AddOn by kornholio
...prints and less noise headaches. to get 7v from atx psu you can connect fan's negative to 5v and...
thingiverse
free
Extruder Titan Aero - Easy Removal from Prusa reprap & from RAMPS - with fan and BLTouch by antontre
...extruder from the printer itself (from ramps 1.4) with e3d titan aero with a fan for printing so i...
thingiverse
free
Haenau - Update by ceri
...a re-design for the back mounts. also a new e3d - easy swap print head dolly, and an untested...
thingiverse
free
3D Printer Mendel Type Small (relatively) by TRENDi77
...homemade project for 3d printer. single homemade hotend or e3d compatible - 0,4 mm nozzle, bowden type extruder. 400w...
thingiverse
free
olinux K8200 mod for E3D V6 on K8200/3Drag by frolinux
...relay between board and heating. i use a 12v atx power supply for the board, and the original velleman...
thingiverse
free
Dagoma Discoeasy 200 - dual head mod by iLouis
...perfect world get two identical hotends (used 12 euros e3d v6 amazn one) attached zip is marlin rc6 dedicated...
thingiverse
free
Delta Printer by TRENDi77
...fan duct with potentiometer. can be used http://www.thingiverse.com/thing:1337200 for e3d5/6 - it will be probably better, than my version...
thingiverse
free
The Bastard 3D Printer by trickius
...it's low performance had to go, was replaced with e3d v6. size of plate is 300x300x260 with original aneta8...
thingiverse
free
Leonardo3d 3d printer by necro133
...(nema17 2a) and 26 teeth drive gear printing head: e3d vulcano 1.75mm 0.6 nozzle (yes it is chinese clone...
thingiverse
free
3D Printer Mendel Type X1(X2) extruder/s by TRENDi77
...offset in the back of the case. clamp for e3d type hotends also uploaded - you have to rework...
thingiverse
free
Dagoma Discoeasy 200 - Diskossel 250 mod by iLouis
...you use your discoeasy parts : mks motherboard, default e3d motors, fan (will need one more), lcd, most cables....
thingiverse
free
Ultimetal - Large 3D Printer by maxdesign1990
...microns leadscrew precision: 100 micron deviation per 300mm hotend: e3d chimera stepper motor: nema 17 1705hs200a 2-amp 1.8-step 0.8nm...
thingiverse
free
Printi4 – Large Scale CoreXY Printer by toxuin
...nema 17 motors, 10-24 threaded rods, 8mm smooth rods, e3d v6 (clone/original) hotend, gt2 belt. electronics: 400w atx power...
thingiverse
free
Stage 1 upgrade list for the ANET A8 by Daltoncnc
...this with a number of upgrades i recommend the e3d v6 bowdon hotbed = factory item i would recommend...