13 duct taz5 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Taz5 Bracket for DiiiCooler Duct by KillaCycle
... peer between the fan duct and the table.
(see my low profile heated bed tabs that you will also need if you install this duct.)
thingiverse
free
TAZ5 Hot End Duct for 25 mm Fan by mtgansler
...5 hot end duct for 25 mm fan by mtgansler
thingiverse
shortened it a bit for easier installation and potentially better airflow.
thingiverse
free
LH Mount for Turbo Fan Duct, Taz5 by KillaCycle
...u might wish to replace the 24volt 30w heater in your extruder with a 24volt 40w heater. you can then run the fan all the way up.
thingiverse
free
Revised Taz5 Single Fan Dual Output Cooling Duct by Brendan
...r the left section, depends on how you orient it on your bed. printing the entire thing at once will definitely require supports.
thingiverse
free
Lulzbot Taz5 extruder fan duct with led lights by hobbyfin
...tage at 20ma (typically) and select the resistor value accordingly. the small loops are to hold the led wires.the fan is 40x10mm.
thingiverse
free
Low Profile Heated Bed Tabs by KillaCycle
...the homed extruder to set the height of the duct when you are first attaching it. rest the duct...
thingiverse
free
Lulzbot TAZ Fan Dual Duct with Tap ready holes by Makuna
...enough to hold the fan. if you have a taz5 or the new hexagon metal hot end for your...
thingiverse
free
Titan extruder mount for lulzbot taz4 and taz5, one fan by Suntorn
...it fits on your taz. this is a final product and is tested on my taz 4. just be...
thingiverse
free
Taz 6 (5 upgrade) fan ducts for e3D v6 by kerthg
...this guide, http://matterhackers.dozuki.com/guide/how+to+install+an+e3d+v6+hotend+on+a+lulzbot+taz+5/5 , and if you have the taz5 it's super easy to upgrade (print) the taz 6...
thingiverse
free
Taz replacement 25mm hotend Fan Duct by KillaCycle
...duct by killacycle thingiverse improved hotend duct for lulzbot taz5 much better cooling of the hotend. cured pla filament...
thingiverse
free
TAZ5 E3D Titan Mount Remixed with stronger back and heat insert holes by meximelt
...holes for easy wire routing. note: the new fan duct will work on the last rev of the carriage...
thingiverse
free
TAZ5 E3D Titan Mount by lasersharkdesign
...issue with this design is for the new fan duct i used the original files, forgetting the fan had...
thingiverse
free
Taz5 Taz4 Kittaz Mods by kendawg
...strip 3/8" wide x 1/16" thick x 33 feet longhttp://www.amazon.com/gp/productb00ee8q83m?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00 15) copper pipe (.25 inch in diameter) vendor: home...