31 door little 2x 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
MakerBot Replicator 2X Door Centering Guide by davedelay
...by davedelay thingiverse maybe your 2x door is a little miss-aligned, maybe you want to sand off the edge...
thingiverse
free
Door holder-closer for Replicator 2x by tom7
...on the replicator 2x does not shut enough. this little thingy snaps around the base and holds it snugly...
thingiverse
free
Door Handle Adapter (no touch, forearm) by ipd-otto
...wash your hands a lot, this is just another little ...
thingiverse
free
Velcro-Stop Door Stop by AxionTheHusky
...itself up when folded, i have since made a little clip for the rod the sit in. it is...
thingiverse
free
cryptobox by CPLK
...many parts : main body of the box the door a lock a sliding "barrel" two keys (one meant...
thingiverse
free
Replacement battery door for Fitbit Zip by tom7
...poor quality battery door that breaks easily (particularly the little tabs that hold it in place). mine finally became...
thingiverse
free
Hood for BCN3D Sigma, after Toobyy (.225" plexi) by Processaurus
...the thicker plexiglass. latches engage further into mating part. door flap accommodates thicker material. door flap may be printed...
thingiverse
free
Magnetic Latch / Lock / Handle for Sapphire Pro Enclosure or 5mm Doors by ddemeterco
...enclosure. pretty straight forward replacement, however, hardware is a little bit different than the original one (m3 nuts take...
thingiverse
free
Replicator 2X Cooling Fan Duct by WorksBySolo
...other versions. this keeps it away from the front door hinge bolts! helpful for pla and abs prints. find...
thingiverse
free
WYZE filament run-out sensor by senioroso
...by senioroso thingiverse filament runout sensor utilizing a wyze door prox sensor. this design utilizes a spring and m8x3...
thingiverse
free
380mm Long Twin Jet Drive Work Boat by Lewist123
...above printed at 50% windows (still to be finished) door cabin roof adapter plates (2x - same file mirrored)...
thingiverse
free
Dismountable 3D printer enclosure by robas
...magnets (12 mm diameter, 1 mm thick) for the door and the side panels perspex panels clear perspex for...
thingiverse
free
Ender 3 Zinus Table Enclosure
...put 2 magnetic latches on the sides of the door (one on the front and back of the table),...
thingiverse
free
DIY Personal Office Desk Cooler (Peltier) by squirtle_93
...and nuts some 2.9mm brass tubing to mount the door some little screws to mount the fans on the...
thingiverse
free
Terrarium Animal Ramp by JustAGermanGuy
...length is: length of board(mm) = heigh of your door rails (mm) / 0,422 ( for example my rails...
thingiverse
free
Top-Door-Opener Ikea Lack Enclosure made stronger by paparazzi
...+ 444 x 488 for front door for a little more margin and confort. it is important to use...
thingiverse
free
IKEA Lack Enclosure for 50x50 / 25x50 side panels by MilosFec
...foot" some of my door panels didn't fit perfectly (door wasn't able to close completely). putting a washer between...
thingiverse
free
Holocron Lighted by Badkitty
...base should also be printed upside down (for battery door recess to print correctly) but no support needed as...
thingiverse
free
Mazda 6 Center Console light
...sunglass compartment and pull firmly down holding sunglass compartment door when clip releases slide whole assembly forward. be careful...
renderosity
$9
Ship Elements F2: Executive Suite
...<br /> figures:<br /> - fully rigged room set (door open through masterdials)<br /> - obl helper <br />...
thingiverse
free
UV Curing Chamber
...a uv chamber like this: ikea eket cabinet with door $25 . ikea spst switch $0.80 amazon aliexpress lcd...
thingiverse
free
GoldenGears hotend zProbe effector (UPDATED) by TommasoEngineering
...(if i remember correctly it is found in the door hardware area). essentially this allows you to swap out...
thingiverse
free
Active Cooling Fan Duct v2 for Replicator 1 / Duplicator 4 / FlashForge / CTC by thruit00
...in duplicator 4x with regularly installed and closed front door and avoids previous known crash problem with front door...
thingiverse
free
2.5" HDD OS Disk Under 5.25" ODD - HP MicroServer by Sibobby1
...the hp microserver’s included odd screws on the hinged door (15% infill hexagonal, 3 bottom, 4 top, 3 perimeters,...
thingiverse
free
2x 3.5" HDD to 1x 5.25" ODD HP MicroServer Adapter by Sibobby1
...the hp microserver’s included odd screws on the hinged door (15% infill hexagonal, 3 bottom, 4 top, 3 perimeters,...
thingiverse
free
Bender-INO v1 by MAkings2018
...card) magnet sensor (has been disassembled from an alarm door sensor... and replaced with a new one! stay safe)...
thingiverse
free
Another useless box
...the bottom, using 4 m3*10 screws. mount the usb door using the usb door frame, to the the front....
thingiverse
free
Nintendo Switch Case Anker PowerCore 20100+ Modification by bacree
...the cartridge pivot first, then the pins for the door as you put the battery in one end and...
thingiverse
free
Adapter to convert ups to emergency light controller by rue_mohr
...its got its front tab trapped under the battery door brace, will usually pull out. ditch it. step d)...
thingiverse
free
MHP 15 by Mrheathpants
...should make vertical printing easier. flywheel left with jam door has been updated to have more room around the...
cults
free
Replicator 2X Cooling Fan Duct
...other versions. this keeps it away from the front door hinge bolts! helpful for pla and abs...