18 cross printrbot 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
PrintRbot Top Joiner - Plastic Cross Beam. by kenwshmt
... down, or build it up with scrap abs and glue it into the hole. if it wont sit 'upright' turn it sideways or upside down.
thingiverse
free
Iron Cross by mayermi
...cross, made in sketchup, optimized to print on a printrbot ...
thingiverse
free
Printrbot Play Crossbar Filament Guide by klowsen
...play.
it's nearly finished, but it has some problems (too tight for 1.75mm filament currently). i'll fix in a few days.
thingiverse
free
Printrbot Tool Holder by sahyun
...drive. it is sized to sit on the top cross bar of the printrbot metal plus. see more of...
thingiverse
free
Basic foot to protect desk from metal printrbot scratching it by wandrson
...to the bottom of the printrbot. it includes a cross hole, that can be threaded m3 for either a...
thingiverse
free
IKEA LEDBERG Z-Axis (Printrbot) holder version 2 by Simonwlchan
...2: cantilevered arm mounted on z-axis head instead of cross beam for more strength arm re-designed for load head...
thingiverse
free
Printrbot Plus Vert. Shaft Extruder Mount for Bowden by tdeagan
...will put the extruder centered (and higher) on a cross bar linking the z shafts. this model is for...
thingiverse
free
Interlocking Rings Puzzle by emmett
...position. just flex them a little to snap the crossng joints apart. they will quickly fall apart to three...
thingiverse
free
'Printrbot Metal Simple' Back Mounted Dual Spool Holder by danielsokolowski
...falling off i slanted the arm 2% angle - cross your fingers i'm printing right now - done, looks...
thingiverse
free
Printrbot Jr. V2 60mm side fan mount and duct by omniverse
...also harder to print? (print with supports) 3.1 adjusted cross again, trimmed a bit off the parts that slide...
thingiverse
free
Printrbot Jr. V2 Stylized extruder pieces (more to come) by omniverse
...plate didn't fit with motor correctly, fixed it, fixed crosscut things update: flattened the bottom of the latch and...
thingiverse
free
Printrbot Play Filament Guide by cedwards
...that, and it hasn't happened again so far (fingers crossd!). note that if you use it with that spool...
thingiverse
free
Compression style Printrbot Simple replacement collar spacer by edd2225
...220grit wet/dry sand paper to the cylinders surface. fingers crossd. i did drill/ream the collar our with a 5mm...
thingiverse
free
Printrbot Jr. V2 40mm side fan mount and duct by omniverse
...trimmed the parts that go in the base, modified crossshaped cut similar to my initial design but with a...
thingiverse
free
Turk's Head Knot (3x5) by jtbowden
...sketchup ruby script i wrote, and then the strand crosssection was extruded along that path. this created some very...
thingiverse
free
Printer... Wind My Watch by Simonwlchan
...45-minute print yielded 11 hours of running for a cross men's palatino automatic watch (model: cr8008-01) that had been...
thingiverse
free
TentRbot - PrintRbot plastic hanger tent attachment by kenwshmt
...further away. these fit over the back of the cross beam blocks, and hold in place by compression. they...
thingiverse
free
PrintrProbe Z-Probe Mount for 2014 Makers Simple Kit by AmazingSpanoMan
...not droop due to heat and will stay put. crossng my...