25 bush probe 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Hypercube Bushing Probe Inductive Sensor Mount by butchja
...#define front_probe_bed_position 64
if you are interested in the pictured fan duct, seehttps://www.thingiverse.com/thing:2517118
thingiverse
free
part fan with probe by kth1022
...to either tap the hole for the x axis bushng or use self tapping...
thingiverse
free
Geeetech prusa i3 x pro E3D lite 6 X carrige with probe by sender86
...to hotend as possible. for bearings i used lm8uu bushngs http://www.thingiverse.com/thing:1196801 probe offset: x=21...
thingiverse
free
Filament Spule 50g-100g by rgrae
...probes. the winding-diameter equals normal 750g spools. there are holes/bushngs to begin and end windings correctly. the idea for...
thingiverse
free
Coin Probe Holster by delsydsoftware
...about the probe tumbling from it's holster into a bush while you crouch over your treasure hole...there may be...
thingiverse
free
Open Model for External Mechanical Stress of Semiconductors and MEMS for Cascade Microtech REL 3600 probe station by buhler
...quantity - description 4 pcs -lm8uu steel linear bearing bushng 4 pcs - 90x12mm steel cylinder liner rail (vertical...
thingiverse
free
Covid-19 self-retracting safety probe w/replaceable tip - *** updated *** by cgfan
...updated with a rear finger guard/stop, added additional internal bushngs (for 4 total), updated geometry to reduce need for...
thingiverse
free
Anet AM8 Conversion Parts by M1dn1ghtN1nj4
...the anet a8. i have other upgrades including drylin bushng on the x and y axis, delrin anti-backlash nuts...
thingiverse
free
Anet A8 X Carriage dual extruder stock and e3d by Bustenchops
...the nozzle alignment right. this carriage uses 16mm polymer bushngs. various 2mm and 3mm screw hardware is needed to...
thingiverse
free
Hypercube 300 CoreXY by adrianm1972
...and optimized for a 4 z rod build. the bushngs for the x carbon tubes no longer take igus...
thingiverse
free
Rostock-compliant bushing carriages, marble joints by andyhomes
...i just was able to use hot-end holder and z-probe designed for rostock platform use in this setup. the...
thingiverse
free
Nimble Gnu - System to Adapt the Zesty Nimble Extruder to a Prometheus V2 Hotend Mounted to a SeeMeCNC Balljoint Effector Platform with Accelerometer Probe PCB by slonold
...a little spacer between the bottom of the guide bushng and the top of the prometheus to make up...
thingiverse
free
Mendel90 Lead screw upgrade (LM8LUU, probe/bottom Z only!) by Arakon
...press them in. i had tried to use bronze bushngs and they were stuck immediately due to the slight...
thingiverse
free
Quick fit carriage system by lukie80
...of 45mm and a 2mm gt2 belt and fits bushngs/bearings with a diameter of 15mm (default) or 16mm (select...
thingiverse
free
Modified X-Carriage for Prusa i3 "Acrylic", Extended Mountplate and Bed-Autoleveling for Prusa i3 by Aut0mat3d
...your own layouts as it includes rods, belts and bushngs/bearings, i have documented is as good as i can....
thingiverse
free
Anet A6 E3D v6 X-Carriage (ZEUS) by chekcian
...default_axis_steps_per_unit { 100, 100, 400, 422.53 } 3d printed bushng for this x-carriage can be obtained here https://www.thingiverse.com/thing:2766583 the...
thingiverse
free
UltiCube by Geaz
...bronze sinter bushings. i had the problem, that the bushngs didn't fit the 8mm rods exactly. this caused the...
thingiverse
free
Dual CoreXY setup that uses LME12UU and 12mm shafts by Thump2010
...it. what i did was to just do a bushng that the bearing sits between so the belt sits...
thingiverse
free
Funbot M8 version by madmike8
...of 5/16" smooth rods with this machine. the bronze bushngs have a 5/16" id 7/16" od and .062” flange....
thingiverse
free
Hypercube 300 - Lite & Piezo Lite Carriage plus Other Mods by EdNiedziejko
...dual leadscrew i'm working on. fine tuning the integrated bushngs: i use a 10mm drill bit, and push it...
thingiverse
free
AndreasL Dual z axis Smartrapcore ALU DjDemonD remix for 2020 with counterweight by DjDemonD
...3mm bearing (or a larger bearing and a printed bushng) the m8 axle (i.e. an m8 bolt with the...
thingiverse
free
Anycubic I3 Mega ULTIMATE Upgrade Guide by petrzmax
...a solution: use igus rjzm-02-08. these are also polymer bushngs but closed in metal case which allows them to...
thingiverse
free
ROB-O Junior FFF 3D Printer using 80/20s 10/10 (1"x1") extrusion by Thump2010
...in my last update that i modified the bearing bushngs and the motor mounts on the 23rd so the...
cg_trader
$20
Probe Bush
...probe bush
cg trader
cmm lab
grabcad
free
KOSSEL (Ver.bettak) - delta robot 3D printer
...20 teeth and 2mm pitch htpa20s2m060-a-h6 6x oil free bushngs - flanged id=5mm od=6mm gfm-0506-04 diagonal push rods 12x...