27 battery balsa 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
strix goblin battery tray by Andyg152000
...by andyg152000 thingiverse i got tired of braking the balsa wood battery tray on small or soft crashes so...
thingiverse
free
Strap hook for Talon Pro/Snow Goose battery bay by Herman_
...straps. glue them in place with a piece of balsa behind it to fill up the...
thingiverse
free
Piper J-3 Cub Balsa Kit Parts by Martinrome
...much better. only problems are the very weak, light-weight battery door latch and landing gear that have no chance...
thingiverse
free
Bootstrap-ready Rover Chassis by Aruut
...fits the hole-spacing of an arduino uno. a spring-loaded battery case can be mounted below the chassis, fits a...
thingiverse
free
LIght weight upgrade, for Muffin RC airplane by Quadkiller
...add ballast on the nose and using a lighter battery ...
thingiverse
free
Acro RC airplane
...with a 3d printer. result is 440 g. with battery you can see performance test of motor with various...
thingiverse
free
TekSumo Motor Mount by cw360
... degrees... file). this mount should force the noise down. this might be good if you are running a light setup and a heavy motor.
thingiverse
free
Micro RC Airplane by niklasm
...15deg flight time: 11min non-printed parts: specktrum ar6410 150mah battery latrax motor latrax bearings latrax gear/propshaft latrax prop 3/32in...
thingiverse
free
Fatshark FPV gimbal pod by Thullen
...fit, no guarantee though.https://hobbyking.com/en_us/fatshark-700tvl-cmos-fpv-camera-ntsc-pal-with-pan-and-tilt.html the pod replaces the planes battery hatch and holds the fatshark servo gimbal. print the...
thingiverse
free
Cheap Flying Wing by Spr0cket
...
the xflr5 source file (complete with vlm1 analysis and stability analysis) is included in the "xflr5 source.rar" file.
thingiverse
free
RS-8: Motorized Airplane by ritterbusch
...tissue covering the wing. it uses inexpensive motor and battery from common quadcopter repair packs resulting in a cost...
thingiverse
free
Futura Printed EDF RC model by wagnergabesz
...wingspan: 1030mm edf kit: dr. mad thrust 1300watt 70mm battery turnigy 3300mah 4s static measurements: 82 ampers thrust:...
thingiverse
free
Muffin full 3D printed RC airplane by Quadkiller
...30a 4s esc 1 x 4s 1400/1500 mah lipo battery 3 x 4g servo (i suggest this for ailerons:...
thingiverse
free
Reptile S600 | Bluntless S800 Sky Shadow by JustinC_FPV
...mark where foam needs to be removed for the battery tray. the battery is pushed pretty far forward because...
thingiverse
free
S600 V2 - Bluntless S800 Reptile Flying Wing by JustinC_FPV
...extend the wingspan to 30". next i increased the battery bay size so it could fit a wider range...
thingiverse
free
FT Goblin Parts by nesteffe
...of the plane body through the top of the battery bay so the fc can be mounted in the...
thingiverse
free
Full ABS RC plane with brushless electric motor by northshore
...- 45mm dia x 2, 20mm dia x1 1300mahr battery motor and prop options as per instructions 1x 4...
thingiverse
free
Elliptical Winged Plane by H1tchens
...round carbon fibre 6x 9g servos and your own battery and esc combination. this plane uses a covering film...
grabcad
free
Balsa Battery Car
... to the grabcad community for the electric motor, rims, and energizer batteries. assembly drawings and instructions are included.
cg_trader
free
Balsa Battery Car
... batteries vehicle model prototype ital design electricity sport car other car motor electric car electric motor electric vehicle
grabcad
free
pusher RC plane
...a pusher plane, made of balsa wood, uses lipo battery to run the 1400 kva...
grabcad
free
Test Frame for Rc Plane
...dimensions of those parts. the blue box is the battery and the white box is the speed controller. the...
grabcad
free
RC F3A Biplane #2
...unner and 8s batteries. note this is not finished, wings should probably be moved a bit rearward to help with cg and have struts.
grabcad
free
F16 70mm EDF
...any airplane.it is 1/10.5 scale, 70mm edf, 4s lipo battery flap and retract. i use materials that depron ,balsa...
cg_trader
free
F16 70mm EDF
...any airplane.it is 1/10.5 scale, 70mm edf, 4s lipo battery flap and retract. i use materials that depron ,balsa...
cg_trader
$25
Schneider GRUNAU BABY IIb RC vintage glider wingspan 2000mm | 3D
...915mm weight : 1,100 ~ 1,200g(ready to fly, include battery 2,200mah, after painting wing loading : 31g/dm2 this aircraft...
grabcad
free
Atmos SPX Hybrid - Fixed Wing UAV System
...re from traceparts or grabcad community (thanks a lot).
https://www.rcgroups.com/forums/showthread.php?4154755-atmos-spx-project