18 air pinion 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
G scale points motor by BrainHunter
...the pinion on the servo i use a hot air soldering iron to warm up the inner of the...
thingiverse
free
Spur Gear replacement parts for TAMIYA SPRAY-WORKS air compressor by 3dxl
...gear tooth and also smaller sub part of its pinion gear. so immediately i 3d modeled a duplicate version...
thingiverse
free
Gear Art Parts by elwood127
...a piston and cylinder and connecting rod and an air tank with gauge. i used a 12 volt, 10...
thingiverse
free
Vibration Table (180x180) by Cagatay
...it for my concrete mold casting, helps to bring air bubbles to the surface, allowing the mold to spread...
thingiverse
free
Convoyeur à rouleaux, entrainement par pignons - Roller conveyor, pinion drive by Digicod
...épaisseur 1,8mm sur lequel je place une chambre à air de vtt à l'envers pour avoir un maximum d'adhérence....
thingiverse
free
ThingMaker - Extruder by robertopaoli
...the pieces are designed so that part of the air arrives above the engine to cool it and the...
thingiverse
free
Powerhobby Increased Airflow Manifold by TheFuzz1542
...attached the motor is cooler even with a larger pinion ...
thingiverse
free
MyRCCar 1/10 MTC Chassis Upgrades (OLD) by dlb5
...one teeth in one of the gears of the pair my last try was with 1:2 mod1 gear-set (21t-22t)...
thingiverse
free
CR-10 or Mini to Prusa i3 conversion kit by AeroFredcom
...do it. cooling fans the ssr will get the air pulled by the psu fan the board has no...
thingiverse
free
BaneBots P60 Gearbox 1/5 Maxstone Crawler Wheels evil-rover02 by evil_k
...the same esc channel), then the motor in the air would be spinning and there would be no torque...
thingiverse
free
DIY RC Street Racing Car: One Week Classroom Project by Banana_Science
...to your frame.-(1 of each)right & left side guard air intakes: these optional side pieces pop into the m3...
grabcad
free
Max-Air 3 way Butterfly Valve Assembly
...assembly using a max-air technology mt46 pneumatic rack and pinion actuator and delta t 4in 051 butterfly...
grabcad
free
Formula-type single seater
...and no internals (crankshaft, camshafts, pistons, rods etc.), formula-type airox, turbocharger (w/ intercooler), water reservoir, radiators and hoses, transmission...
grabcad
free
Shore Power - Wave Energy Device
...that converts linear motion to piston’s reciprocating motion-this causes air compression and compressed air flows out through outlet. there...
grabcad
free
Ventilato (Ambubag ventilator)
...a rack and pinion system which will push the air in and out of the ambubag. in order for...
grabcad
free
Double 775Pro DoubleBack CIM-SIM-CIM-ile
...without removing gearbox or even taking gearbox apart. *** air paths for cooling 775pro -- you really need air...
cults
free
DIY RC Street Racing Car: One Week Classroom Project
...down to your frame. -right & left side guard air intakes: these optional side pieces pop into the m3...
cults
$19
Mk Ultra - 3D printable 1/10 4wd buggy
...fan. it will aid with motor cooling by circulating air inside the body and directing it over the motor....