17 10mm r1 2 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
3D ROBO R1 Dual Fan Mount "Black Widow" 10mm and 20mm fan setups by TechSupportGo
...l?_encoding=utf8&colid=1ix7yr7u22m7o&coliid=i3okv5mmopxl26
tested.
please read all instructions before getting started.
thingiverse
free
Optical Filament Runout Sensor Enclosure by warpster
...position like i ran into.you will need an m2 10mm bolt and nut to tighten the center adjustable piece...
thingiverse
free
2020 led mount by Old-Steve
...it would accept an 8mm strip instead of the 10mm strip. i designed new mounting brackets for the 2020...
thingiverse
free
DimSim R1 Button plate by snubbs
...m5 nylock nut 6x m5 washers 3x m5 x 10mm alu washer https://www.aliexpress.com/item/33052017430.html?spm=a2g0s.9042311.0.0.27424c4duaeopx 1x stm32f103c8t6 "bluepill" - (make sure...
thingiverse
free
KIS extruder - direct drive Nema 17 & Mk8 for 1.75 filament by Phil_Maddox
...with their v6 kit. the fitting sits in a 10mm dia hole 10mm deep and once in place a...
thingiverse
free
Robo3D Y Axis Cable Chain by galaxius
...or 3mm bit and work your way up to 10mm in 1-2mm increments. printed in pla with 3 perimeters,...
thingiverse
free
Robo3d Titan Extruder Mount by YogiG
...is a slide on duct for a 40mm x 10mm parts fan in the front and rear. test print...
thingiverse
free
Robo3d R1 E3D Flex Filament Guide by valkary007
...then try with flex. try slow speeds at first (10mmsec?). thanks! video here: https://youtu.be/5tzsodht6zk 215 degrees, 15mm/sec, filaflex, 110%...
thingiverse
free
Printinz clamps for DaVinci 1.0 Pro by Old-Steve
...at 20mm wide go in the front. 1 clamp 10mm wide goes in the back. print in abs with...
thingiverse
free
ePIc R2-Pi2 (raspberry pi 2 or 3 case ) by Tripnutz
...stay in place. uses a 40mm x 40mm x 10mm fan - and still would be enough room for...
thingiverse
free
Anycubic Kossel Linear Plus carriage tensioner by Old-Steve
...3x20mm screw for the tensioner. this gets me about 10mm of adjustment. that doesn't sound like much, but if...
thingiverse
free
Low noise E3D-V5 Fanduct by GIL3D
...positioned fanduct this fanduct is for both e3d-v5 standard nozzle(10mm and volcano nozzle(20mm) 이 팬덕트를 만들었던 목적은 1.e3d-v5 에서...
thingiverse
free
Linear Actuator large by Brucestephen
...part #gfl-25 https://www.igus.com/product/?artnr=gfl-25 the shaft coupler is 30x42 with 10mm x 12.7 mm bore the carrier assembly for use...
thingiverse
free
Open Model for External Mechanical Stress of Semiconductors and MEMS for Cascade Microtech REL 3600 probe station by buhler
...steel zinc-plated phillips pan-head machine screw 4 pcs - m4x10mm stainless steel zinc-plated phillips pan-head machine screw 132g -...
thingiverse
free
Portable Led Light by NirDobovizki
...on a camera. on the other side there's a 10mm hole that can fit a worklight tripod and a...
thingiverse
free
3d printed cable roller and waterproof control box for a Schill GT380 reel to turn it into a ROV or robot tether by piercet
...stainless bolts (should be 12 8mm ones and 4 10mm ones) and 4 12mm m3 botls and nuts for...
thingiverse
free
Skelestruder V1 for Prusa MK3 and MK3s by jltx
...or stock with larger idler (offset). recommend cutting 2 10mm piece of belt and insert in paths not used...