Threads worm 3d models
Warning. This content is not moderated and could be offensive.
m4
3dmdb logo

62 threads worm 3d models found

Download or buy, then render or print from the shops or marketplaces. 3D Models below are suitable not only for printing but also for any computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on your favorite 3d printer or render them with your preferred render engine. Please note that the 3D model database is only a Search Engine. You should visit the original websites. Most of the models can be easily imported and rendered with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online 3d model conversions tools for your file format.
thingiverse
free
Parametric Worm Wheel for Threaded rod by cgapeart

Parametric Worm Wheel for Threaded rod by cgapeart

...ith a small threaded rod. i changed the profile of the worm gear and tweaked it so that it was shaped for standard threaded rod.
thingiverse
free
An alternative, non threaded crank and worm for the $3.47 3D Scanner by l0rd0ct0d0rk

An alternative, non threaded crank and worm for the $3.47 3D Scanner by l0rd0ct0d0rk

...into blender, and made a square joint because my threads were printing out too big for the crank to...
thingiverse
free
Worm Gear Set Example by dreyfusduke

Worm Gear Set Example by dreyfusduke

...center distance 48.1mm 2.54 module size worm = 2 threads wheel = 30 teeth please like it if you...
thingiverse
free
Worm and Wheel by barty3d

Worm and Wheel by barty3d

...they do trick the slicer into putting the worm threads above the first layer allowing the full thread form...
thingiverse
free
Worm Gear 2.5 / 1 Ratio with Frame by AnyWorldGames

Worm Gear 2.5 / 1 Ratio with Frame by AnyWorldGames

...to 1 ratio worm gear in a frame. it uses 3 mm bolts to hold it together. it uses 4 mm threaded rod and nuts for the drive shafts.
thingiverse
free
Tetrix Worm Gear by MrD_Leonard

Tetrix Worm Gear by MrD_Leonard

...can get expensive. the size and pitch of the threads seems to match up pretty well with existing tetrix...
thingiverse
free
Linear Actuator Worm Gear by davidlvann

Linear Actuator Worm Gear by davidlvann

...tup. i've found several surplus linear actuators that i intend to use to drive a recyclebot type filament recycler/extruder.
thingiverse
free
Pile 'o Polyhedrons: the Improved Screw by syvwlch

Pile 'o Polyhedrons: the Improved Screw by syvwlch

...ust received my thingomatic, however, (thanks mbi!) this might take a back seat to assembly, calibration, printing, etc... sorry!
thingiverse
free
ElectroMag-Test-Jig by MJHeed

ElectroMag-Test-Jig by MJHeed

...half upside down so it will print the gear threads cleanly (no clean up after!) and added a 10mm...
thingiverse
free
Parametrische Schnecke / Parametric Worm by janssen86

Parametrische Schnecke / Parametric Worm by janssen86

...be calculated out of its module m, number of threads z and lead angle γ: r = m·z·1⁄2sinγ format:...
thingiverse
free
Filament roller

Filament roller

...red to the upper shelf via the m4 worm. the supports are always placed on three rolls and are designed for pitch 120mm m8 screws.
thingiverse
free
Pedal Adjustment Gear - Gen 2 (2003-2006) Ford Expedition by CinderGuardian

Pedal Adjustment Gear - Gen 2 (2003-2006) Ford Expedition by CinderGuardian

...have a thread inside the bore. i modeled the threads for the accelerator pedal gears. however, because it proved...
thingiverse
free
NEMA 17 Worm Gear Box 60:1 by Bencil88

NEMA 17 Worm Gear Box 60:1 by Bencil88

...rod ~ 30cm m8 lock nuts with nylon insert 4 m3 bolts 6 skate bearings (608rs) * 4 tools: hack saw files allen keys 13mm spanner
thingiverse
free
adjustable spanner by dan241297

adjustable spanner by dan241297

...et it to work smoothly. a 40mm m3 screw holds the worm gear in place and cuts its own thread into the handle so no nut is needed.
thingiverse
free
Mini 4 Jaw Chuck (independent) by PRIma

Mini 4 Jaw Chuck (independent) by PRIma

...rclockwise. i did not tested the chuck yet in any machining operation therefore please be careful and wear always safety glasses.
thingiverse
free
PowerPac Extras by Caramellcube

PowerPac Extras by Caramellcube

...parts, try splitting them in half so there is no overhang in the thread (check out the video by elproducts for more about this).
thingiverse
free
Worm Drive, Non-Throated by syvwlch

Worm Drive, Non-Throated by syvwlch

...o the gear's pitch radius divided by the screw's mid profile radius, with a sign depending on the screw's handedness.
thingiverse
free
Hive Super-Tiles by zealtv

Hive Super-Tiles by zealtv

... worm: https://boardgamegeek.com/thread/928112/worm-additional-hive-piece there's also blank tile stl as a jumping off point.
thingiverse
free
Smaller Worm Gear set for Nema17 by TAz00

Smaller Worm Gear set for Nema17 by TAz00

...t have needed. the cross shaft is made from a bit of 5mm threaded rod, about 60mm long, using 5mm nuts as spacers and fasteners.
thingiverse
free
Telescope Worm Drive by mcdewey

Telescope Worm Drive by mcdewey

...end needs to be tapped since it has no threads (my modeling skills are up to making threads yet)....
thingiverse
free
Worm gearbox by unclouded

Worm gearbox by unclouded

...eeth for a different gear ratio and the cage will automatically resize itself to fit. the shafts are standard m2 cocktail sticks.
thingiverse
free
LEGO gear flex shaft extruder (24T Gear)

LEGO gear flex shaft extruder (24T Gear)

...od 11mm long extruder wheel. 13.5mmx35mm stainless tube or shaft for the worm shaft ========================== 2019.12.25: update
thingiverse
free
ZWO EAF Holder for  Celestron Edge HD 9.25

ZWO EAF Holder for Celestron Edge HD 9.25

...thread. freecad source on my github update 2019-12-08 version 2 add belt tensioner 2019-12-11 version 3 improved belt tension
thingiverse
free
Gear 30 tooth by RollyR

Gear 30 tooth by RollyR

...attempting to make a worm drive with fast lead threads (5 1/2 threads per inch). the carriage hit the...
thingiverse
free
Anti-Backlash Piece for the Z-Axis of a Solidoodle 2 by toguan

Anti-Backlash Piece for the Z-Axis of a Solidoodle 2 by toguan

...on ether side of the z-axis worm-screw. it isn't the best, but it seems to work fine for me. hope it does well for others.
thingiverse
free
TESLA Knob 2PF 242 06 by GreyhoundDesign

TESLA Knob 2PF 242 06 by GreyhoundDesign

...o looks good. you must add a metal ring to the knob with a hole and thread for the worm screw for full functionality of the knob.
thingiverse
free
3D printed high torque gearbox – Building an electric hoist – worm gearbox by Retsetman

3D printed high torque gearbox – Building an electric hoist – worm gearbox by Retsetman

...c 775 motor(100 watt) -608zz bearing x3 -6004 bearing x2 -20 mm aluminium shaft -m8 threaded rod -cotter pins --2x30—x4 --3x50—x1
thingiverse
free
OpenScad Helix for custom 2D profile and many thread types by zuiopl

OpenScad Helix for custom 2D profile and many thread types by zuiopl

...file for the parameters. but the code is commented. threads already implemented (not exact iso specifications): metric threads square...
thingiverse
free
Worm Gear + Casing compatible with Lego by Shymeck

Worm Gear + Casing compatible with Lego by Shymeck

...m rafts: not needed supports: not needed while printing upside down, but the results may vary, depends on your printer abilities.
thingiverse
free
DeWalt™ DWE7492 better tilting mechanism by WK_2033

DeWalt™ DWE7492 better tilting mechanism by WK_2033

...: 1x dwe7492_wormgear_v5.stl 2x dwe7492_radialwormgearsupport_v2.stl 2x dwe7492_clamp.stl 4x screw m4x50mm 4x nut m4 8x washer m4
thingiverse
free
1/15th Ton Jack Screw by 3DPRINTINGWORLD

1/15th Ton Jack Screw by 3DPRINTINGWORLD

...advisable to use lithium grease on both the gears, threads and the...
thingiverse
free
Metal axle with bearings for M416 trailer by Woyta

Metal axle with bearings for M416 trailer by Woyta

...le to leaf spring i used m3 threaded rod bent to u shape with help of heat and secured with m3 nuts. or you can just use zip tie.
thingiverse
free
55/35 special gear set for pi approximation on Harrison lathe by nglasson

55/35 special gear set for pi approximation on Harrison lathe by nglasson

...a harrison l5 lathe. this is useful for turning threads to suit worm gears. 55/35 is a pretty good...
thingiverse
free
Joustra by jan-stinissen

Joustra by jan-stinissen

...n airport control tower. i don’t have many memories, except a word that greatly impressed me: radiogoniomètre (direction finder)!
thingiverse
free
Tank updated Gear Cases for Kyosho RF006 worm gear set by fastmike75

Tank updated Gear Cases for Kyosho RF006 worm gear set by fastmike75

...the 6mm axles and bearings. use the old cases if you drill out your worm to 1/4" shaft and use 1/4"x5/8" bearings.
thingiverse
free
Axial scx24 pass through middle axle for 6x6 by Gm1972

Axial scx24 pass through middle axle for 6x6 by Gm1972

...r, use an drill as an lathe to get the correct size and then just drill an hole through the stock diff cover for the axle output)
thingiverse
free
Heavy Duty Sperical Parallel Manipulasator by King_Bluetooth

Heavy Duty Sperical Parallel Manipulasator by King_Bluetooth

...bearings on the joints to help with any friction issues that arrises. possible application of somem sensor to make it quto level.
thingiverse
free
Torsen Limited Slip Differential by pizzachef

Torsen Limited Slip Differential by pizzachef

... any parts seem missing or incorrect, please let me know. there were several iterations of a few parts and i may have missed one.
thingiverse
free
Reolink B800 Camera mounting plate

Reolink B800 Camera mounting plate

...damaging the philips head and still allow the screws to get a very good grip. i hope this makes your installation a bit easier!
thingiverse
free
Linear actuator using geared retract motor. by tahustvedt

Linear actuator using geared retract motor. by tahustvedt

... set screw on the bottom of the housing to lock the gearbox in place, and attach short m3 screws to the hinge point if necessary.
thingiverse
free
Belt Tensioning Tool, iOptron CEM25P

Belt Tensioning Tool, iOptron CEM25P

...belt would slip. the screws only engage by 3-4 threads into soft aluminum. parts needed: 4x m2.5 x 40mml...
thingiverse
free
Screw/ Worm drive filament extruder Bowden by GadgetGuru314

Screw/ Worm drive filament extruder Bowden by GadgetGuru314

...1986k710 for securing screw 1x 2in wood screw (sharper threads the better). 1x matching 1/4'' hex driver for chosen...
thingiverse
free
"Heck Meck" soap dispenser by frimmel

"Heck Meck" soap dispenser by frimmel

...it via "object->settings" if slic3r is used, and set it to 60% fill). please do not forget the post-processing step.
thingiverse
free
Anycubic Kossel Linear Plus  flex3drive flexible bowden remote motor  Effector upgrade  E3D V6 (Volcano too) and 5015 blower by rosch8

Anycubic Kossel Linear Plus flex3drive flexible bowden remote motor Effector upgrade E3D V6 (Volcano too) and 5015 blower by rosch8

...s still under the test you need to set 2800 steps per mm for the first iteration and then make calibration of extruder for sure.
thingiverse
free
Rostock Max V2 Nimble Mount by Turpinator

Rostock Max V2 Nimble Mount by Turpinator

... your hotend may separate on the bottom of the peek portion, thats fine. thats where mine did the first 5 times i opened it up.
thingiverse
free
Variant construction set by Michal_G

Variant construction set by Michal_G

...of the components, 60-100% for screws and nuts. regarding threads accuracy, i designed and tested everything to be mix-and-match...
thingiverse
free
Swing Down Bicycle Storage Lift by doublec4

Swing Down Bicycle Storage Lift by doublec4

... way in helping me bring you better content as often as i can! follow me on instagram! ► https://www.instagram.com/embraceracing/
thingiverse
free
fischertechnik N20 Mini Power Motor system by juh

fischertechnik N20 Mini Power Motor system by juh

...eaving a "like" or posting your make as a token of appreciation for my work. find my other fischertechnik designs here.
thingiverse
free
Miniature Vice 2.0 - No metal parts required by HD_Creator

Miniature Vice 2.0 - No metal parts required by HD_Creator

...help to smoothen the surface until everything runs lights. once there is no noticeable friction any more, the will be no warm-up.
thingiverse
free
Easy Clamp for CNC Machine (SainSmart 3018)

Easy Clamp for CNC Machine (SainSmart 3018)

...slightly. finally, screw and unscrew to loosen up the threads have fun and if you're in the holiday spirit,...
thingiverse
free
3D Print Drum Sander by BusterBeagle3D

3D Print Drum Sander by BusterBeagle3D

...p;pf_rd_r=pykgdhfk4gaj8avpmwp5&psc=1&refrid=pykgdhfk4gaj8avpmwp5 608 bearing 6x m3x8 bolts 3x m3x12 bolts wires superglue
thingiverse
free
3D Printed Braille Display by pyrophreek

3D Printed Braille Display by pyrophreek

...0131003132420%26meid%3d7975608331830605768%26pid%3d100005%26prg%3d20131003132420%26rk%3d5%26rkt%3d6%26sd%3d181414292588&rt=nc
thingiverse
free
Vixen GP Goto Conversion Using Meade DS Motors by wt808

Vixen GP Goto Conversion Using Meade DS Motors by wt808

...gp style gem mounts using meade ds-series motors", v1.2 2/14/2003https://www.cloudynights.com/ubbthreadsattachments/677648-retrofit_v1.2.pdf "adding autostar goto functionality to your existing telescope", christopher...
thingiverse
free
CARP Box 3D Printer by thorgal

CARP Box 3D Printer by thorgal

...l for now. optical endstops in x and y axis will be tested one i will get my hands on them. same with proximity sensor in z axes.
thingiverse
free
3D Drucker mit Kreuzkinematik mit 120g Direct Extruder, Nema 14 Stepper und kugelgelagertem Druckkopf auf Carbonwellen by astfaellergerald

3D Drucker mit Kreuzkinematik mit 120g Direct Extruder, Nema 14 Stepper und kugelgelagertem Druckkopf auf Carbonwellen by astfaellergerald

...drill, grind at high speed. then clean and grease well. then connect the motor to the worm axis using the 4 / 5mm shaft coupling.
thingiverse
free
Virpil CM2 Throttle Fingertip Detents by gubernator46

Virpil CM2 Throttle Fingertip Detents by gubernator46

...ed the afterburner detent to afterburnerdetentv2 and added step, stl and a jpg corrected the typo in the ball bearing designation
thingiverse
free
tinkerMicroscope MK1 by tinkerheart

tinkerMicroscope MK1 by tinkerheart

...their lenses – chances are that they have rms threads – if they do not then perhaps you can...
thingiverse
free
Gosainthan, Competition RC Rock Crawler (Super Class) OpenRC by GonzaloChomon

Gosainthan, Competition RC Rock Crawler (Super Class) OpenRC by GonzaloChomon

...ill be added shortly transmitter programing and mixes will be added shortly more pictures and action videos will be added shortly
thingiverse
free
Getriebe Bibliothek für OpenSCAD / Gears Library for OpenSCAD by janssen86

Getriebe Bibliothek für OpenSCAD / Gears Library for OpenSCAD by janssen86

...be calculated out of its module m, number of threads z and lead angle γ: r = m·z·1/2sinγ format:...
thingiverse
free
SILVIUS extruder: Belted 1:5 BMG dual gear  by Baltojikale

SILVIUS extruder: Belted 1:5 BMG dual gear by Baltojikale

...1x wood screw (12-16 mm length, 2.5 mm od (threads included)) 1x 22x3 mm rod/ pin or m3 screw...
thingiverse
free
Bed_Hoist_for_a_3D_Printer_ (D-Bot, Core_XY) by printingSome

Bed_Hoist_for_a_3D_Printer_ (D-Bot, Core_XY) by printingSome

.... edit (29-11-18) correction in notes : 8x gt2 idler pulleys 20 without teeth, ø3mm bore, belt width 6mm -> v3c. thanks zakote
thingiverse
free
UV curing Station for SLA WITH TIMER

UV curing Station for SLA WITH TIMER

...re drill holes so that there was no forcing threads to go thru as i dident want to crack...