26 snap macbook 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
MacBook Pro Snap-In Feet by netherby
...glues or plastic welding.
print/slice at at least 0.1mm layer hight for the top pole so that the snap-in ring is formed properly.
thingiverse
free
Pebble Time Charging Dock by evansjonathan16
...charging dock by evansjonathan16 thingiverse pebble charging dock that snap to the side of a macbook...
thingiverse
free
![Macbook Pro 13" [2015] by Goananndan](/t/8858442.jpg)
Macbook Pro 13" [2015] by Goananndan
...models although i don't know. it also isn't a snap in...
thingiverse
free
Magsafe 2 Stabilizer by __ShapeLabs__
...harried by my magsafe 2 connector because it often snaped out off my macbook. so i created a little...
thingiverse
free
Macbook 30W USB-C charger cord organizer -A2164 by Jmusicman1993
...macbook air usb-c power adapter - a2164. the piece snap in place around the power adapter. it snaps over...
thingiverse
free
MacBook Power Brick Wire Retainer by dhoyt7141
...wire leaves the power brick housing. print two, they snap it where the original went. charger teardown &...
thingiverse
free
Connector for Generative Design Stand for MacBook by szilviu
...print 1 or 2, glue them together or just snap them in...
thingiverse
free
Laptop Legs for KBC Poker 2 by IFoundTheMagic
...laptop legs for kbc poker 2 by ifoundthemagic thingiverse snapon legs to hold your poker 2 above the built-in...
thingiverse
free
Cord Spool for MacBook Power Adapter by JinxTheRabbit
...in the design so the little white plug will "snapquot; into...
thingiverse
free
Macbook Pro Cord Protector by JCC_Starguy
...was at the point of greatest strain and it snaped after two days. it does take a bit of...
thingiverse
free
Replacement feet for MacBook Pro by northriver
...would be to modify the part so that it 'snaped' into place and was held by friction ... i...
thingiverse
free
MacBook Pro Stand 13inch 2009 by Wampo
...your mac from scratches remove upper clip and added snap, fits in firewire and cd slot (stand is not...
thingiverse
free
Macbook Pro Magsafe-r Power Cable Support by MrGabinator
...computer. this part has 2 sides that mirror and snap to each other. just print the same part twice!...
thingiverse
free
macbook feet
...are replacement feet that most of the time just snap in and no glue needed but depending on how...
thingiverse
free
macbook power supply handle by jag
...up and get it square so that it actually snap into place correctly. this little handle makes it much...
thingiverse
free
Macbook Cord Clip by VanBot112
...up in 1% increments until you get a nice snap one side will be very tough, that'll be the...
thingiverse
free
laser cut portable laptop stand 1/8th inch acrylic by clairetuna
...crossbar is also shorter on the edges to prevent snaping if a person dissembles the sides one at a...
thingiverse
free
Charging Cable Guides for MacBook (Pro) - 15" and 12" (2016) by jakereeves
...iterated it a few times to get it to snap onto the charger without fracturing when made of pla....
thingiverse
free
Ultimate Photographer Travel Utility by nickelbeee
...of these magnets (glued in place) to keep it snaped shut. www.amazon.co.uk/magnet-expert%c2%ae-4mm-thick-neodymium/dp/b008u9rvhs the usb reader...
thingiverse
free
MacBook USB C Power Adapter Cable Keeper by timpmandan
...slip over the incoming power first (long cord) and snap over the usb cable. printed in pla at 40%...
thingiverse
free
iPad high stand for Sidecar by aeberbach
...a 12.9 ipad pro. when the pivot pieces are snaped together and the pipe is inserted the pivot join...
thingiverse
free
Subway Map Laptop Stand by mattmillr
...i used. in fact, both sides were tight and snaped when i forced them together. the stand you see...
thingiverse
free
Adjustable Laptop, Tablet, or Document Stand by nlarson
...14"/36cm long are supported. included are files to print snap in tpu bumpers which serve as anti-slip pads. these...
thingiverse
free
12VDC or 24VDC universal laptop power supply w/ anderson powerpole connectors by taxilian
...pressing towards the bottom of the case should then snap it in between the wall and the small protrusion...
thingiverse
free
Vive Pro 2 Headstrap no-stop mod by nEuDy
...also the 3d printed inserts, till they are fully snap into it's final position. important! if you going to...
thingiverse
free
Bowden along shaped like a Feet by shivinteger
...: bsd license [4] thing title : macbook pro snapin feet [4] thing url : http://www.thingiverse.com/thing:1321253 [4] thing author...