19 wire bose 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
BOSE M2/M3 wire mesh mounter
...verse
wire mesh hook/mounter for
bose m2/m3 (computer music monitor) active speaker.
actually i used wire mesh selling in daiso.
thingiverse
free
Bose Soundlink Mini Phone/Tablet Holder Wire mount by jonnyhoeven
...und and projecting the sound in the right area.
i also included the solid edge part file which is editable in synchronous mode.
thingiverse
free
Bose Speaker Corner Bracket (for high wall mount) by SiegeDesigns
...bracket for high corner wall counting with holes and wire slots for audio...
thingiverse
free
Audi Q7 BOSE Subwoofer Spacer by rsilvers
...note that the bose driver is 2 ohms, so wire the new one to also be 2 ohms. it...
thingiverse
free
PSVR Bose Headphone Adapter Clips by supaevensteven
...head if needed. i managed to place the headphone wire inside the headband but it was very very fiddly...
thingiverse
free
Bluetooth Module Housing for Bose Soundock Series 1 by grp1964
...a bose sounddock series i, and the module is wire to the docking circuit board on the module to...
thingiverse
free
Wire Wrap / Cable Shortener by GigaKnight
...i created this thing to wrap my extremely long bose headphones cable, as it would catch on things as...
thingiverse
free
Bose QC35 headset jack thingy
...the rod. professional cable management. --> use qc35 as wire anc...
thingiverse
free
Cradle for Bose Sound Link 3 Speaker by N2GX
...pring (~3mm diam.)
4 small felt or rubber feet
scrap of single-sided copper pc board material
knife, soldering iron, solder, etc.
thingiverse
free
Bose Sounddock replacement front by S13_Mills
...ro w and some wiring. once i had done this, i wanted to clean up the lines of the dock by removing the (now redundant) dock part!
thingiverse
free
Bose QuietComfort 20i iPhone5/5s clip by milkandbourbons
...of the phone 62mm wide and 10mm thick the wire wont get pulled and it makes it super easy...
thingiverse
free
Bose Companion 3 Series 2 Back panel for plate amp by Crazgfrog
...subwoofer terminals shouldnt be soldered, tinning doesnt allow the wire to be crimped properly and creates a weaker noisier...
thingiverse
free
Bose QC3 Bluetooth Adapter by watersb1323
...my qc3s to allow bluetooth connectivity and remove the wire thus i created the design below. i appreciate it's...
thingiverse
free
LasKKit Sound DIY 20W Bose Soundlink Mini Clone by LaskaKit
...with cable https://www.laskarduino.cz/jst-xh-2-2-54mm-2pin-konektor-s-kabelem-female-male--20cm/ jst-xh-3, 3pin connector with cable https://www.laskarduino.cz/jst-xh-3-2-54mm-3pin-konektor-s-kabelem-female-male--20cm/ wire about 0,5m 8x m3x50 f-f spacers https://www.laskarduino.cz/distancni-sloupek-f-f-m3-50mm--nerez/ 22x m3x8...
thingiverse
free
Galaxy Note 2 Clip for Bose 20i QC Headphones by milkandbourbons
...is one with a little clip for guiding the wire and one without. up to you which you choose......
thingiverse
free
Bluetooth Headphones
...(https://www.jaycar.com.au/spare-li-ion-battery-pack-to-suit-gt-4110-quadcopter/p/gt4113) *dpdt power on/off switch (https://www.jaycar.com.au/sub-miniature-dpdt-pcb-mount-switch/p/ss0823) *hook up wire (https://www.jaycar.com.au/hook-up-wirepack-2-metres/p/wh3025) *tactile switch x2 for volume up and down (https://www.jaycar.com.au/3-5mm-spst-micro-tactile-switch/p/sp0602)...
thingiverse
free
Retro Mini Computer Speakers (Nine Oh Ones) by CompuGlobalHyperMegaNet
...speaker, who would have guessed that! i will upload wire schematics soon, just haven't had time to draw that...
thingiverse
free
Headphones - wireless Bluetooth (BT) or wired by yogib3ar
...ok.) 6: 2 speaker drivers 40mm - i used: https://www.banggood.com/30mw-replacement-earphone-speaker-unit-for-boseqc25-headphone-p-1232965.html?cur_warehouse=cn (€3.26 per pair) in my experience 40mm drivers are...
3dwarehouse
free
Office desk (wires managed) / escritorio de ofic. c/ admcion de cables
...added a doble high-end shelf system (for cpu and bose companion 5 sub woffer) a power surge for all...