18 wide mendelmax 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Mendelmax upper vertex 5mm wide ridge by M66
... by 3dsuppli, original ridge was to wide for my aluminum profiles this is 5mm wide, other dimensions are the same as in original.
thingiverse
free
Wide 10mm MendelMax Y Rod Holder by IsaacDW
...i hope to stabilize my print surface and possibly create enough space for dual y-axis motors. from rod center to center is 240mm.
thingiverse
free
Rigid Wide X Carriage for Mendelmax 1.5 by PD5DJ
....
my extruder carriage contains a greg wade extruder with a e3d v6 hotend,
2 fan mounts are mounted on each side of the hotend.
thingiverse
free
mnadamn's Wide MendelMAX 1.5 by mnadamn
...motor mount. also added the sketchup build file.
1/25/13 - flipped mounting holes for the x end stepper motor needed
fan mounts
thingiverse
free
Y-Axis Belt Mount for MendelMax 1.5 by MishaT
...of cable ties. sized for gt2 2mm pitch 6mm wide timing belt which is standard on the...
thingiverse
free
Clip-On R.U.M.B.A. for Mendelmax or T-Max by e-nozzel
...for m3 nuts (5,65mm) 2 versions: "2020_t10_m3_rumba.stl" is 100,2mm wide for standard t-max lower frame "2020_clips_mendelmax_90mm.stl" is 90,2mm wide...
thingiverse
free
MendelMax LED Power Supply Bracket 20A 114mm Width by Blue_Alien
...from lulzbot so i edited it to be 114mm wide ...
thingiverse
free
MendelMax Printrboard Extrudrboard enclosure with lid by Bellus
...mendelmax 1.5. the exterior dimensions are 180mm long 75mm wide it has the cutout for a 40mm fan on...
thingiverse
free
y carriage set for MendelMax 1.5 by Uranos
...fine. this set is for lm12uu bearings, htd3m 9mm wide belt and 12mm rod's. added source...
thingiverse
free
MendelMax 1.5 by kludgineer
...this a work in progress, it is still not widey tested. i recommend this design even for new users,...
thingiverse
free
Super simple MendelMax spool support. by CaptainObvious
...made this supports to hold 10 and 8 centimeter wide spools on top of my mendelmax 1.5. each support...
thingiverse
free
MendelMax by kludgineer
...the recommended suppliers). the required extrusions are available world wide from a variety of suppliers. in addition to greatly...
thingiverse
free
Vertical X-axis Belt Mount with Built-in Tensioner by MishaT
...to tightly trap the standard gt2 2mm pitch 6mm wide timing belts used on the mendelmax. the grooves are...
thingiverse
free
MendelMax 2.0: SPDT Switch Plate w/ Guard by filipvalica
...recessed within the misumi rails. the guards are spaced wide enough for large hands to tighten the retaining nut....
thingiverse
free
MendelMax Power Supply Mounting Brackets by DR2D
...power supply for my mendlemax 3d printer is 113mm wide with two sets of 4mm taped holes (top and...
thingiverse
free
LCD mount brackets - RepRapDiscount lcd panel on MendelMax2.0 by ssaggers
...it. these clips hold a nominally 55mm wide, 1.6mm wide board, but have been designed to allow for some...
thingiverse
free
Brass Leadscrew Nut Adapter by osgibson
...to fit. i used this with http://www.thingiverse.com/thing:21705 on a wide mendelmax...
thingiverse
free
Mendel Dual groove mount holder and bowden tube by RatInDaHat
...groove mount extruders as long as they aren't too wide j-heads work nicely. for the bowden tube holder i...