22 vent slope 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
archive3d
free
Vent 3D Model
...model archive3d cooker hood cooking hood kitchen equipment vent slope - 3d model for interior 3d...
thingiverse
free
Cellphone Vent adaptor by bbeanan
...it to the dash. also designed with a 20 slope to tilt it up a bit. the double cross...
thingiverse
free
Dodge Ram Vent Mount for iPhone by devtty1
...vent to close. the vent still closes, but the slope of the face leaves the phone at a viewable...
thingiverse
free
Danby Air Conditioner Vent Connector by avolkov
...extend bottom section a little bit to accommodate a slope that will not need supports in automatic support detection...
thingiverse
free
Customizable 2 Parts Fan Adapter by kijja
...from the both side or small fans to bigger vent if a large fan goes to a small vent,...
thingiverse
free
OO/HO Gas Works (Low Profile) by calvinstreeting
...works building part 1: general pipe part 2: exhauster vent part 3: ammonia washer's part 4: iron sponge purifier...
thingiverse
free
Replacement Ceiling Mounting Plate for the Ubiquiti UniFi AP-AC Lite and AP-AC LR by ctpearson
...with vents to help release that heat and to prevent the pla from slowly melting. i will post the...
thingiverse
free
Car Vent Phone Mount - 1998-2002 Honda Accord by jonle
...with removing supports from such tiny holes. changed the slope of the mounting arms to 45 degrees to remove...
thingiverse
free
CD phone holder by frankvdh
...not have the phone held in front of the vent so i don't get the cooling or heating. so...
grabcad
free
Industrial Continuous Ventilation - Top Ridge Ventilation
...type of vent installed at the peak of a slope roof which allows warm, humid air to escape a...
grabcad
free
750 litre milk storage tank with skid, pump and steps
...pump and steps. lagged tank, manway, capacitance level probe, vent inlet. sloped base with slipper...
grabcad
free
Process vessel 2800 litres
...off lifting lugs, inlet with angle filling horn to prevent foaming. this tank is used for cheese starter culture...
grabcad
free
chemical tanks module-a
...one point lift, all made out of stainless steel, vent cut out the angles roof framing to avoid trap...
cg_trader
free
Chemical tanks module-a
...one point lift, all made out of stainless steel, vent cut out the angles roof framing to avoid trap...
grabcad
free
chemical tanks module-b
...one point lift, all made out of stainless steel, vent cut out the angles roof framing to avoid trap...
cg_trader
free
Retro House
...access and bathroom. in dept details include a stove vent in the roof. i hope i didn't bore you...
grabcad
free
Texas Adapter
...here: https://www.homedepot.com/p/danco-35-o-rings-10-pack-96749/100277539 the snorkeling mask can be found here: https://www.amazon.com/divelux-snorkel-mask-snorkeling-ventlation/dp/b01mf4j3j7/ref=sr_1_4?crid=2f9s1era90sol&dchild=1&keywords=divelux+snorkel+mask+-+full+face&qid=1586282481&s=sporting-goods&sprefix=divelux+%2csporting%2c305&sr=1-4 an example of the type of filter used can...
3dwarehouse
free
Louvered Gable Attic Vent
...louvered galvanized metal attic gable vent for 6/12 roof slope #attic #gable #louver...
3dwarehouse
free
Biulding with tall chimmeny
...italy #chimmeny #italy #milan #rounded #sloping #tall #unknown #unusual #ventd ...
3dwarehouse
free
livable shed 10'x12'x11' with a loft and a balcony, deck on a sloped backyard
...fixed window (deck mount) * 2' x 3' skylight ventng window (deck...
3dwarehouse
free
Retro House
...access and bathroom. in dept details include a stove vent in the roof. i hope i didn't bore you...
3dwarehouse
free
The Throne Room - tiny raised bathroom in hallway closet on 2nd floor
...basement, and again sideways to the septic drain. a vent stack would likely need to be tucked into this...