17 transmitter nighthawk 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Nighthawk 200 FPV Transmitter cover by r3gou
...hingiverse
cover for fpv transmitter. it has small edges to align onto place but it will need to be secured with tape or similar
thingiverse
free
Rctimer LT200 transmitter holder Emax Nighthawk by mrorange26
...ransmitter holder from rctimers.it bolts through on back of quad.cabletie to hold it in.
i printed with cura 0.2 with 33% infill.
thingiverse
free
Emax 250 Nighthawk Boscam TS351 transmitter tray by CybrGuy
...r the two bolt holes are 43mm apart.
i also made a smaller version for the ts5823 here: http://www.thingiverse.com/thing:826152
thingiverse
free
Emax 250 Nighthawk TS5823 transmitter tray by CybrGuy
.... there are 2 slots on each side so you have options for zip tying it down.
the centers for the two bolt holes are 43mm apart.
thingiverse
free
Emax Nighthawk 250 Eachine Video Transmitter tray by CybrGuy
...cut out the support material for the arch after you print. its my first time doing support for an arch so it may be a bit crude.
thingiverse
free
LT200 Video Transmitter Mount for Emax NightHawk by RotorGator
... cover is attached with simple cable tie held in place by the base walls. the base also is open allowing the heat sink to breath.
thingiverse
free
Angled LT200 Video Transmitter Mount for Emax NightHawk by RotorGator
... cover is attached with simple cable tie held in place by the base walls. the base also is open allowing the heat sink to breath.
thingiverse
free
TS832 Case for Nighthawk 250 by skydge
...for nighthawk 250 by skydge thingiverse case for ts832 transmitter holes for nighthawk 250. scale piece x 10 for...
thingiverse
free
Antenna SMA Seat Holder for emax/nighthawk 250 pro by metalnow
...using extending line to prevent the sma seat of transmitter broken while crashing in the...
thingiverse
free
EMAX 250 Nighthawk FPV antenna & XT60 mount by jimflint80
...then mount to it. please note - your fpv transmitter will need an extension lead for the antenna, to...
thingiverse
free
Fatshark 5.8 250mw transmitter holder by kellyds
...the fatshark 250mw transmitter. it fits on an emax nighthawk frame on the rear. i fastened mine with four...
thingiverse
free
Boscam VTX mount for Nighthawk 280 by rcmike
...nighthawk 280 by rcmike thingiverse i modified the boscam transmitter case with deported antenna from rboutrois so it would...
thingiverse
free
Nighthawk eachine vtx mount by kristofera
...from an earlier version. the new version moves the transmitter 4mm further back to make the sma fit through...
thingiverse
free
Emax Nighthawk 249 by scratchymaster
...for easy angle changes. two flight controller & video transmitter mounting locations. arms can swap out in 15 minutes...
thingiverse
free
Angled LT200 Video Transmitter Mount for ZMR250 by RotorGator
...together. see original for more images. adapted from emax nighthawk to now do zmr250... as i do not have...
thingiverse
free
XRace360 Copter by Bitfrost
...system and additional hardware like a gps, a telemetry transmitter and 4k cameras. finally a nice case and wings...
grabcad
free
Nighthawk 250 Quadcopter
...a power distribution board for cc3d, a ts832 video transmitter and a flysky fs-r6b radio reciever. the 1300 mah...