18 teeth printrbot 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Printrbot idler pulley with 18 teeth. by eddiema
...y x - carriage seems to be running smoother than before.
if your belt is already running true then adding this may be a bad idea.
thingiverse
free
Printrbot LC and LC+: Y Bearing Guide for GT2 32 teeth pulleys by gyronictonic
...8 bearings back a few to make everything fit.
by all means, go for a 18 or 25 teeth instead, don't make the mistake we made!
thingiverse
free
Printrbot LC and LC+: Y Bearing Guide for GT2 32 teeth pulleys DERIVATIVE by trth
...tive.
credit where credit is due:
i have to say the original design is a great concept and give all the credit to gyronictonic.
thingiverse
free
Printrbot Simple Filament Guide by jcubed111
...to prevent the filament from slipping out of the teeth of the extruder...
thingiverse
free
PrintrBot LC small extruder gear by WildWill
...screw hole, and replaced some missing vertices in the teeth same gear, better mesh, less...
thingiverse
free
Beefier helical extruder gears for printrbot by zack112358
...printrbot to be stronger and easier to print. the teeth are fatter and stubbier so that infill reaches into...
thingiverse
free
Printrbot on Steroids by LXDickman
...be careful on the shells on the large gear(hollow teeth ...
thingiverse
free
Moose Bottle Topper by YardCamel
...flat brown primer. the white of the eyes and teeth is rustoleum flat white. the black on the nose...
thingiverse
free
Printrbot Original Improved extruder spur gear Greg Wade's by galaxyman7
...with 100% infill in the orientation shown. the gear teeth overhang so they will start out sagging, but it...
thingiverse
free
Spur Gears for Printrbot (Printed Extruder) by Drawcut
...18 pressure angle: 20 deg small gear (pinion): 13 teeth large gear: 43 teeth addendum modification factor: 0.35 solidworks...
thingiverse
free
Ribbon cable clip for Raspberry Pi Camera by WaveSupportApparatus
...along the side of my printrbot simple's bed. rounded teeth on the inside surface of the clip grip the...
thingiverse
free
(Discontinued project) Clay's direct drive extruder: 3-Piece, Latching, Easy Print (Printrbot Jr. V2) by omniverse
...inside -rounded that a corner on the latch -added teeth on bottom of the inside when the extruder is...
thingiverse
free
Evil Jaws by daewootech
...the eye is eviler, the fins are swooped, the teeth are more shark like and to top it all...
thingiverse
free
Printrbot 2.0 Derived + 20x4 LCD Controller (WIP) by openhardwarecoza
...the mix (e.g. bearing guide compatible with gt2.5 32 teeth pulleys) and my left side panel (used to neaten...
thingiverse
free
Printrbot Jr. Upper & Lower Filament Guides (1.75mm) by phraust
...having issues with my filament slipping out of the teeth of the hobbed bolt halfway through a print (too...
thingiverse
free
Simple Belt Tensioner for Printrbot Jr -- GT2 belts by selmo
...3d0g. i've made the following changes: reworked slot and teeth to fit gt2 2mm pitch belt. added a third...
thingiverse
free
GT2 Belt Wedge by iamjonlawrence
...be kept for future upgrades. simply interlace the belt teeth with the notches of the wedge, and insert into...
thingiverse
free
Enclosure for LCD 12864 Smart Display Controller
...i'm using 20%. print with support so that the teeth on the clips are well formed. graphics case knob...