28 sensors stud 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
ASP FS400 magnet ring and sensor bracket by Darkith
...off the sensor and align the depth with the magnet ring, then hot-glue it into the bracket with the flat side facing the magnets.
thingiverse
free
Parametric pulley with studs for slip ring for use in POV display by criznach
...or. paired with a smaller pulley and belt, this powered a 1 meter pov display.
slip ring:https://www.sparkfun.com/products/13064
thingiverse
free
R-Motion Clip by Dekko777
...es m4 x 20mm studs and nuts.
please choose the best fitting clip before tightening the thumb screw otherwise the clips may break.
thingiverse
free
CR6 Filament Sensor Mount for use with Bondtech BMG (mirrored) by cyberFluke
...le persuasion, sits on the studs inside the arms of the guide. (note: screw the bracket to the machine before fitting the wheel.)
thingiverse
free
OCULUS RIFT SENSOR WALL AND CEILING MOUNT
...thingiverse a wall and ceiling mount setup for the sensors of the oculus rift. just two parts and a...
thingiverse
free
Universal Filament Sensor - Hemera+MMU2 Compatible
...0mm long, threaded into the plastic base, and then clamps onto a mounting brackets using the remaining thread as a mounting stud.
thingiverse
free
Garmin Cadence Clip with zip ties support by szymon_sz
...ing holds fine - so far so good.
keep in mind this is probably worst model you have seen, i have almost no experience in cad/cam.
thingiverse
free
BrickScope: RMS threaded 8x10 stud brick
...rs the optical axis midway between the 4th and 5th stud, but the alignment during design was approximate, so may be slightly off.
thingiverse
free
Hemera mount CR6 by RebelMD
...* i am still working on a cover to go around the hemera and transfer board****
i will be releasing different versions stay tuned!
thingiverse
free
Project Predator: Nerf Stryfe mod by vaeddyn
...n, because i'm terrible at code - please let me know, i'm pretty sure i'm doing some things the hardest way possible.
thingiverse
free
SAMBUCCA - Chassis - Level 0 - Drive by hede3D
...lighting , running light, gripper, rfid reader (waypoints), ultrasonic sensors (4 pieces), internal power monitoring , gps, gyroscope, light-dark...
thingiverse
free
Elongated E3D V6 Fan shroud for Duet Smart Effector And 30mm Blower (radial) Fan Mounts by DjDemonD
...or sunon 5v 0.68w 30mm blower fans, attach these to the ball stud m3 screws with nuts and bond the fans onto then with superglue.
thingiverse
free
jbperf Dual VR Conditioner Board V2.1 Enclosure by rccardude04
... for something else.
the connector cutouts work with the jst-xh type connectors used on 3-cell lithium r/c battery balance leads.
thingiverse
free
Ugly Parametric Magnetic Effector by rodsmith
...ilament entry hole. i've left the code in the .scad file in case somebody else might want to modify it into something useful.
thingiverse
free
12v Thermostat W1209 Housing, Case with pushbuttons -- W1209 Gehäuse mit Druckknöpfen by SolarGermany
...on a wall, the cover lasts by itself). board: https://de.gearbest.com/sensorspp_240514.html?wid=1433363 link to manual: http://forum.hobbycomponents.com/viewtopic.php?f=73&t=1900 maybe you are also interested:...
thingiverse
free
Colonial Meeples playset
...although it all gets a little fiddly, grenades, motion sensors etc. at some point i'll look at either putting...
thingiverse
free
CR-6SE Direct Drive Conversion by BostonBowser
...nk to the stepper motor i used:
https://www.amazon.com/gp/product/b01lespdcq/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=utf8&psc=1
thingiverse
free
Ramps 1.4 Enclosure for Vslot by spauda01
...;redirect=true&ref_=oh_aui_detailpage_o03_s00
i used the mega standoff footprint from http://www.thingiverse.com/thing:915320
thingiverse
free
Replicator 2/2X DuetWifi Upgrade by IdefixRC
...sor mount and part 3 for the duetwifi configuration files (dual extruder).
enjoy your new, wifi connected, replicator printer :-)
thingiverse
free
MECHANIC VENTILATOR - COVID 19 - LOW POLY by Costa_D
...is still under 200mm ! on version "b", two sensors can be install - using the threaded bar as...
thingiverse
free
MECHANIC VENTILATOR 4 - COVID 19 by Costa_D
...with the appropriate washers. bag holding arms and additional sensors are going to be secured on those threaded bars....
thingiverse
free
MECHANIC VENTILATOR 4 - COVID 19 - HIGH POLY by Costa_D
...with the appropriate washers. bag holding arms and additional sensors are going to be secured on those threaded bars....
thingiverse
free
Elegoo Mars Array / NanoDLP Overhaul
...mount the duet micro sd) ability to integrate more sensors and adjust homing position and behavior. (duet) ability to...
thingiverse
free
Emerald Flail Snail Monster for Tabletop Games by jawsnoir
...regrow in a month if lost. even without these sensors the snail can still move about reasonably well, as...
grabcad
free
Misting System Room
...assembly of room, including studs, nozzles, piping, housing for sensors and room for...
grabcad
free
Ghost Post
...to different colours. only senses objects that are 400 to 500 grams therefore when someone walks out it would not change colours.
grabcad
free
LARGE Custom CNC Machine with ATC Spindle and 10 tool Pneumatic tool-rack
...z-axis pepprl and fuchs barrel and box style proximity sensors on all axes 25mm acetal in natural color (can...
3dwarehouse
free
Black and Decker BDSL30 24-Inch 3-in-1 Gecko Grip Level
...u make your mark. #black_and_decker #hand_tool #hand_tools #home_imporvement #layout_tool #layout_tools #level #levels #measuring