thingiverse

free

Elongated GoPro Screw adapter (works with gopro bolt snap adapter) by jlcnuke1

...updated gopro bolt to work with my gopro to boltsnap adapter. this fits well using a m5-0.8 x 50mm stainless steel hex head bolt.

thingiverse

free

DJI FPV RC Controller elongated Stick by defillo

...ontroller stick for enhanced precision just 6 mm longer, but makes the difference requires a m2x15 screw must be printed in resin

thingiverse

free

Ikea Desk Headphone Hook by MajorZer0

...te larger headbands and an elongated screw hole for more compatibility. printer will need to be able to bridge the bottom cutout.

thingiverse

free

TUSH-E The ultimate Spool Holder - Elongated by Motorpixiegimbals

...file for fusion360. added 2.3mm pilot holes for 3mm screws if...

thingiverse

free

Enlongated Knurled 1/4-20 Camera Mount Screw by dereksrose

...y mount screw wasn't long enough. i elongated the screw just under 5mm and chamfered the base since the mount is countersunk.

thingiverse

free

Hotwheels Clamp by buzzkillg230rc

...sed inward is 28.8mm if you are going to need a smaller opening when the clamp is tightened you will have to elongate the screw.

thingiverse

free

Logik fridge freezer door handle by Kodie

...layer height 0.1, support material default value. printed via simplyfy3d. screw holes are a tight fit, may need opening a little.

thingiverse

free

Bird Feeder top by Andyeb

...ent i designed. it does screw on but if you are not confident it will hold, glue it in place and fill the feeder from the bottom.

thingiverse

free

Internal Switch Holder by juper42

...ting hole have been elongated to hold switch and screwed down to internal plate metal rod is just a piece of threaded control rod

thingiverse

free

BLtouch mount E3D and FN Cyclops 3 in 1 out by techtho

...v2.0: elongated the mount to reach all 4 fan screws in case you don't have both top or bottom...

thingiverse

free

Air conditioning exhaust tube adapter by antoniofiol

...conditioning exhaust tube adapter by antoniofiol thingiverse this item screws onto the exhaust tube of a portable air conditioning...

thingiverse

free

RunCam SkyPlay 30degree Tilt FPV Mount; RMRC Goby 210 by user84

...through the sides. do not over torque the side screws they can strip...

thingiverse

free

Jumper T16 Handle Hinge by twistedartwork

...prop it up higher on the bench. use m3 screws with nyloc nuts to adjust the hinge resistance. print...

thingiverse

free

Ender 3 Pro Cooling Ring Remix by Cosse42

...remixed this ( https://www.thingiverse.com/thing:4147944) just to fit the vent screws i elongated in fusion 360 the bracket parts by...

thingiverse

free

Bitfenix Colossus Foot by bdiesel

...n and elongated it. the screw mount is in the same place just outside shell is longer. needed a long thin screwdriver to install.

thingiverse

free

iPad 2 Wall Mount hooks by autoexecbat

...so shaved a bit off the screw hole end making it sloped, for a more universal and better fit - if the wall in not perfectly flat.

thingiverse

free

AR15 Thumbhole Stock by wt808

...ned screw or another upper buttplate screw). please post a comment or message me if the updated models improve or worsen the fit.

thingiverse

free

Phone stand remix by pakkun48

...improvements. for best results, i recommend using two m8 screws instead of the printable...

thingiverse

free

Mini Tripod by niko_at

... for assembling you will need at least: 3 x screw m4 x 30mm 3 x elastic stop nut m4 update: added feet for elongation (stackable)

thingiverse

free

Openbeam holder Bracket for Full Graphic Smart Controller by NilsR

...kossel mini. affix the controller board with four m3 screws and washers, and if necessary, nuts. uses the same...

thingiverse

free

MPCNC 23.5 Universal mount (HicWic) that is flush to Z bottom by Mdheld

...scad file to elongate it and raise the mount screws ...

thingiverse

free

Improved AR-15 wall mounts by TJEmsley

...holes that accommodate standard 2-1/2inch truss head cabinet mounting screws suitable for both right hand and left hand uppers....

thingiverse

free

Elongated Filament Bracket for Taz 6/Other by db11883

...x10mm (i believe that is the size i used) screws then i mounted them to the extrusion frames using...

thingiverse

free

OSMM Catapult by kellyegan

...ch to ball hold to hold ball better added screw hole to base for mounting tightened up press fit so arm doesn't come out.

thingiverse

free

Necklace with Closure by pmoews

...net/openscad-threads/ stl files are: short_bead.stl long_bead.stl clasp_top.stl clasp_bottom.stl openscad code is included.

thingiverse

free

Hi Point 995TS Muzzle Brake Addon for Shroud by Ambeos5

...so you could adjust the hieght by using set screws on the bottom and top. also in order to...

thingiverse

free

Sim Racing Paddle Shifter Elongated Arm by Junkyard_godz

...i've also used a furniture connecting screw as a shaft for the arm, you have to source locally a solution that works for you.

thingiverse

free

Ultimate Customizable Corner Brackets by Hultis

...mode for 2040 and similar extrusions configurable amount of screws and screw sizes in two axes handles 45° to...

thingiverse

free

Filament Guide

...top rail. on the ender 3 pro the mounting screws for the filament spool holder prevented the grip-rectangle from...

thingiverse

free

Voltage Alarm and Frsky X8R Housing for Emax Nighthawk Pro 280 by TheRealADY

...the top plate slots -front corners can run into screws attaching top plate to standoffs changelog: 2/24/2017 -enlarged screwdriver...

thingiverse

free

Bow Stabilizer Cell Phone Mount by jviper093

...got quite a bit of wobble out of it when i shot it tonight. may try printing with more infill density to add some more stability.

thingiverse

free

Servo Holder bearings with cover by sa64

...y/electronics/servo-holder-options donate zav6402@gmail.com paypal my page:https://sites.google.com/view/hobbiesforhobbiesandlife

thingiverse

free

S-360-12/S-360-24 Power Supply Cover by purgedsoul

...ed printing time), beveled and rounded some of the corners, elongated the screw holes for it to fit on other oem s-360-nn models.

thingiverse

free

AR15 ARC Stock by wt808

...ost a comment or message me if the updated models improve or worsen the fit. updated 3/26/2018 - added skeletonized arc-l version

thingiverse

free

Anet 8 Z switch mount

...e for bigger wires.i added a guset to the rear to pull it away fron the z motor for more wire room. i elongated the screw holes.

thingiverse

free

Servo mounts bearings by sa64

...y/electronics/servo-holder-options donate zav6402@gmail.com paypal my page:https://sites.google.com/view/hobbiesforhobbiesandlife

thingiverse

free

Steel Cable End by chewbaccah

...ully. using this part may not work for everyone (or even anyone) due to length requirements for your individual situation. enjoy

thingiverse

free

Hexagon HotEnd cooler (40mm fan) for OrdBot Hadron and BulldogXL Extruder by wolken

...on. enhanced airflow on hexagon cooler. edit 27.12.2015: upload rc3 version. enhanced airflow and fix symmetry of elongated hole.

thingiverse

free

CR-30 Filament Sensor and Feeder Holder for larger spools (2kg) by marvin_bauch

... aluminum profile and 2 in the elongated holes of the part to secure the filament sensor. they hook into the plastic on rotation.

thingiverse

free

Anet A8 e3d v6 Bowden Print Carriage Redux Remix for CloneE3D by RPSthlm

...without friction. this makes it easier to tighten the screws for the bearings without putting stress on the rods...

thingiverse

free

Ipad Wall Bracket For Holding 12.9" ipads by tswalter

...it which allows for leveling the bracket if your screws are not perfectly plumb. you may want to adjust...

thingiverse

free

E3D V6 hotend mount for Geeetech A10 by the_chris_davies

...mount). hardware for hardware, this print uses: -2 m3x35mm screws -2 m3x16mm screws -4 m3 nuts the 35mm screws...

thingiverse

free

Raspberry Pi 3, Pi 2, and Model B+ case with 200mm VESA mount extension by LotarInc

...hole. for the case connection, you need 4 m4x10mm screws for the tv connection you need 4 m6x16 screws....

thingiverse

free

iPad Mini Vesa by jwestonh

...g to any size variants. at the moment this is being printed for testing, but i liked it enough so far to at least post a preview.

thingiverse

free

CR-10/Ender 3 Hotend Fan Duct BLTouch Remix by raeuberhose

...the fan duct so i could use the longer screws for my 4020 cooltek silent fan. printed with fan...

thingiverse

free

Prusa I3 MK2 Camera Mount by tbergman8

...m3 25mm screws will be required replacing the standard screws if you built the kit, there are probably 2...

thingiverse

free

Alternate Filament Feed Bracket (no screws needed!) by dmtrotter

...close the pulley was to the feeder, so i elongated it and bent it outward a bit. i also...

thingiverse

free

Toilet Paper Holder / 3D Printer Filament Spool Holder - Voron style by Imprimildo

...pad for use with double sided adhesive tape or screws the original voron part was edited in freecad. frecad...

thingiverse

free

Monoprice Select Mini X Support: Altered screw holes by Leesamn

...unt an anderson power connector. i'm using http://www.thingiverse.com/thing:1205771 to panel mount a higher amp power supply.

thingiverse

free

Z-Axis Stepper Bracket for TEVO Tarantula by colinrgodsey

...both right and left side brackets. i would recommend abs, i have had pla z brackets warp over time, especially with ambient heat.

thingiverse

free

NXT Armored Case by OnionRobotics

...it. feedback is greatly appreciated as we are always working to improve this case. our contact info is listed on our userpage.

thingiverse

free

Temperature Controller Enclosure by jdurand

... cooling. a #4 nut slides into the pockets in the side tabs so you can screw the lid on. i made the name plate on a cnc mill.

thingiverse

free

Anycubic Kossel glassbed fixtures by fernanor

...inner/outer diameter: 3.2mm/7.0mm if anyone wants the freecad file (could not upload here) for tweaking, feel free to contact me.

thingiverse

free

Air Funnel Prusa I3 mk3 by Viczena

...the covers look good in neon orange with blackend screws update 11 22/7/18: version11 is improved in that it...

thingiverse

free

Hemera Claws Fan Duct Standalone

...be used with no other mounting parts just 2 screws to mount to the hemera and 5015 blower fan....

thingiverse

free

BLTouch pin holder for Craftbot Flow printers by AndreasALu

...slide the top of the holder from the mounting screws and push the tip of the pin through the...

thingiverse

free

The Planetary Dynamo-kit! [DCmotor, LED and all print: no extra screws needed] by marius1991

...the upscaled aubenecs-design, our idea includes a costumized handle, elongated screws, and a one-off dc-motor/led-housing turning the gears into...

thingiverse

free

Monoprice Maker Select Plus Rear mounted fan duct by davoo2017

...you will need to use 2 pieces of m5 screws (preferably 20 mm in length). the spacer is slanted...

thingiverse

free

Rev Battery Box

...ap screw for strap retainer plate:m4x12mm socket cap screwm4 acorn nut box hook:heat set threaded insertm3x12mm socket cap screw

thingiverse

free

Strengthened optoma projector base plate with cutout for bolt hole. by kentronix

...f these are a good idea of not, you have to decide for yourself. i accept no responsibility of course. i am using a optoma hd25e.

thingiverse

free

Dog Nail Grinder by Zq8blazer

...dogs nails and not to cut into it. doing so will cause profuse bleeding. i suggest reading a how-to on properly grinding nails.

thingiverse

free

Drill Press Base w/Clamps by RossRobotics

...for clamping down your project. slots are for 6/32" screws that are 10mm long. the larger slots on the...

thingiverse

free

Cover for 64x32 LED Panel with 4mm Pitch (P4) by mkngrm

...nsistencies depending on the manufacturer, as i did have to elongate the screw holes used to hold the frame pieces to the matrix.

thingiverse

free

Stealth Desk Drawer by mcclock

...the same mounting brackets. all you'll need are 4 screws to secure the brackets, make sure the screws aren't...

thingiverse

free

Elongated E3D V6 Fan shroud for Duet Smart Effector And 30mm Blower (radial) Fan Mounts by DjDemonD

...blower fans, attach these to the ball stud m3 screws with nuts and bond the fans onto then with...

thingiverse

free

Maylan M150 Z Axis Screw Stabilizer by SkyNerd

...to the upgrade. additional parts: 4x m3x 20 hex screws (same as whats on the printer, just longer, you...

thingiverse

free

Simplified Ender 3 Hotend & 5015 Partcooling Duct replacement by raeuberhose

...between the carrier and the hotend and tighten the screws once finished you can install the axial fan on...

thingiverse

free

Prusa Mk3 R2B x-axis modifications by martin_au

... ridiculously easy to damage so that misalignment would occur. (and the instructions are basically promoting this to occur)"

thingiverse

free

Mendel90 spool holder (customizable) by CookieMonster

...ine up perfectly. update (v1.2) (20-4-2013): improved the rod support bit, with a better and more predictable snap fit setting.

thingiverse

free

Big-Filamentholder with a twist by TThiemann

...g. next to the spindles you can see both screws the big one is optimal for 1.8 kg and...

thingiverse

free

50-60W CO2 laser tube hanger for SH-G350 laser cutter by bratan

...support doesn't have space for nuts, instead 10-24 machine screws are screwed directly in the plastic. basically i wasn't...

thingiverse

free

Prusa 3 Dual Extruder upgrade kit by EMG

...plastic itself. extruder and support are joined by two screws m4x65 or m4x70 threaded rod and associated nuts and...

thingiverse

free

Snapmaker 2.0 3D Printhead Bowden Tube fitting Adapter Plate by fastcompjason

...design didn't account for the chamfer in the countersunk screws and there was a lot of wasted thread length...

thingiverse

free

18650 Battery Bank 2.1A with super cheap Board from AliExpress by Light24bulbs

...easily just be elongated downward to fit more cells. if you comment and i manage to see it, i'd be happy to do that for you.

thingiverse

free

Peopoly Moai Build Platform Leveling System by Insaisissable

...spider and lock it in with the four back screws the screw holes are elongated in order to allow...

thingiverse

free

Anet A6 Power Cover with Switch and Receptacle (for original A6 power supply) by Kingmiwok

...be careful if you plan to attach it with screws (as opposed using a thru-bolt with a nut). if...

thingiverse

free

VORON Precision Piezo Carriage by aMpeX_fhm

... (6mm and 5mm, respectively) make sure to remove the bowden coupling in your hotend if you're using a plastic bowden coupling

thingiverse

free

Anet A8 Double 80mm Fan Bracket by samlynn79

...the anet a8 stock, and uses the same two screws that used to hold that stupid waste of space...

thingiverse

free

Skil tripod quick release camera mounting plate with 35mm square by laurent_despeyroux

...er with hidden nuts version of the base : big-base-thin.stl if someone want to update its print. new enhanced design will follow.

thingiverse

free

Adjustable Z-axis NEMA 17 mount bracket for 20x60 extrusion by slarti42uk

...allow for m4 x 16 socket cap or panhead screws -- update -- having printed out two sets and...

thingiverse

free

Power Supply Mount Case Hypercube modified V1.3 by regzzz

...uot; version of the switch and power inlet. it's v1.4, enjoy cheers a big thank you to tech2c for all the work and sharing!

thingiverse

free

Wltoys 144001 [Beefed up] Extra Room Under the Body. (Lowered Second Floor Brace)) by cyrexxx

...holes in the bodyposts are 10mm deep. so max screwsze would be around 11mm? also important: when using the...

thingiverse

free

3DFused Stepper-Shaft support and Adjustable End Stop mounting bracket by estrato

...basically solid. you'll need a bearing and some m3 screws and nuts. 1 piece of 4x11x5 bearing 4 pieces...

thingiverse

free

Anet A8 ShottyMount bowden carriage fast change by danshotty

...use blocks you can mount with a couple of screws i suggest you to mount assemblies touching bed with...

thingiverse

free

Printrbot Play X-Axis drag chain by trunzoc

.... please forgive the rough nature of some of the parts. video of the chain in action:https://www.youtube.com/watch?v=boucfc49e_q

thingiverse

free

K8400 Mainboard Cover by Bo_Ris

...with 0.3 mm resolution, brim, no support. use m3x16mm screws update 17-sep-2017: shortened wall enforcement that was running into...

thingiverse

free

HEvo HyperCube Evo Height Adjustable 3-slot Fan Duct by blindmoe

... you to modify but since fusion360 changed their hobby tier functions i can no longer export in .step, so please don't ask ;)

thingiverse

free

WANHAO Duplicator i3 Z-Axis extension by retrofluffyboy

...need a about 30 m3 x 8mm socket head screws a 2.5mm drill and an m3 tap (or if...

thingiverse

free

HyperCube 3D Printer M4 Variant by zargony

...mount to 20x20 extrusions are modified to use m4 screws instead of the default m5. therefore it's possible to...

thingiverse

free

Knee or mecanic elbow by routex

...motor - 2x bearing 8x12x3.5 - 8x m2.5 8mm screws - 6x m2.5 nuts steps: 1 - cut a...

thingiverse

free

Adjustable Caddx EOS Beta75x mount by Thump2010

...at information and he is the fastest indoor pilot i have seen on youtube.https://www.youtube.com/channel/ucbgpbee0g9echygycrrd4hg

thingiverse

free

Knee or mecanic elbow (Compact model) by routex

...sg90 servo motor 1x bearing 8x12x3.5 4x m2.5 8mm screws 3x m2.5 nuts steps: 1 - put a small...

thingiverse

free

Anet A8 top frame brace | Anti Z wobble by vektorviktor

...the back, so you have easy access to the screws on the upper side. the files are named [l]...

thingiverse

free

Sphere Painter by jam513

...more secure mounting of the servo motor using both screws in the middle of the piece. the third modification...

thingiverse

free

Bowden Extruder Chassis by prototypes_and_pixie_dust

...duct that securely attaches to the frame with two screws and doesn't overlap with the bed leveling sensor like...

thingiverse

free

Modular Robot Under-Actuated Modules (ZaMoBot) by czarama

...hobby servo which allows lower final cost. besides the screws for the base and servo, the module does not...

thingiverse

free

Accessory Container for "USB Bore Scope Holder" by elhalpern

...ot zip tie using vinyl electrical tape. this gives me good aiming control when i drop the camera into walls and the like. enjoy!

thingiverse

free

DiiiCooler for Wanhao Duplicator i3 / Maker Select by Pawpawpaw85

...for dimensions datasheet) [mounting instructions] 1) use the m3 screws and nuts to fasten the cooler in the two...

thingiverse

free

Wire Connectors (Quick Connect/Disconnect) by GlowingEmbers

...solder them, shouldn't happen. no other parts required no screws no springs. just press fit. easily separated yet firm...

thingiverse

free

Multicolor Un-Manufacturable Part by mathgrrl

...ke license. if you want to use designs, images, or files outside of the terms of this license, please email request@mathgrrl.com.

thingiverse

free

SD - Micro SD Card Reader Support, Anet 6 by ggpp01

...ar=443275371899 at amazon a little more expensive:https://www.amazon.com/micro-extension-adapter-flexible-extender/dp/b06xy5qb2z

thingiverse

free

Tronxy X3 or X3a Bed upgrade (double remix) and new y - tensioner flipped by fts1999

...has been designed to use the original m4 8mm screws and t-nuts. it was designed with to be used...

thingiverse

free

Parametric 3 axis manipulator - optional servo mounts* by BadenLab

....com/watch?v=bwgxrefry9qhttp://www.youtube.com/watch?v=boiq2rsf7ighttp://www.youtube.com/watch?v=ljo5oysrims&feature=youtu.be

thingiverse

free

Über Design Ü180 -- Uber Design U180 by theledman

...tube: https://www.amazon.com/arris-wrapped-carbon-glossy-surface/dp/b00rwyanky/ref=as_li_ss_tl?ie=utf8&qid=1451875565&sr=8-1-spons&keywords=10mm+carbon+fiber+tube&psc=1&linkcode=sl1&tag=foubardes-20&linkid=f8d4e2dafb943481eb5363007520129b matte 6mm tube: https://www.amazon.com/arris-wrapped-carbon-glossy-surface/dp/b00rwyanky/ref=as_li_ss_tl?ie=utf8&qid=1451875565&sr=8-1-spons&keywords=10mm+carbon+fiber+tube&psc=1&linkcode=sl1&tag=foubardes-20&linkid=f8d4e2dafb943481eb5363007520129b assembly: insert 4 screws through bottom of mid slide 6mm tubes into mid...

thingiverse

free

Bottle Flute/Whistle by CTKerswell

...o get a few people together and make some songs out of them :) i hope i win, a new printer could replace my currently broken one.

thingiverse

free

HeaterMeter v4.3 Customizable Case by CapnBry

...the front left and right corners 2017-apr-15 lcd mount screws returned added option for no lcd/button holes (untested) 2017-apr-11...

thingiverse

free

EnderLoop by mcsgroi

...holes in the parts i designed are for m3 screws so you can enlarge the holes in the models...

thingiverse

free

Loches Z Axis Upgrade for MakerGear Prusa Mendel by Lochemage

...fix this, i changed it from using the tension screws (on the bottom of each x-end) to just having...

thingiverse

free

Modular Mounting System by HeyVye

.... 15/10/20 - updated holder for phone clamp so it can swap orientation. 18/10/20 - new m5 knobs. more tolerance on phone clamp.

thingiverse

free

Orbiter Remix for e3d tool changer by w1ebr

... easier. you can continue to use a hand power drill to break it in. the stepper motor may get quite hot so be careful holding it.

grabcad

free

Screw scissor lift mechanism

...esigned the project with the reference from internet and youtube. solidworks 2017 has been used here for designing the cad model.

grabcad

free

Engine Timing Plate by AV

...that the plate is movable, relative to two mounting screws of the housing, over a selected angular range for...

grabcad

free

Cabinet Latch 2

...layer height and 15% infill on a prusa i3 mk3s printer. no print supports required. i hope you can find this print useful, too.

grabcad

free

Electronic LEA Strength Tester

...can be procured separately. 1)wrap reel (imperial system) for making lea. 2)direct yarn count balance for determining the count.

grabcad

free

M15 Sight Mount for Xproducts Can Cannon

...fun anyway. hardware i used 2-steel raised knurled-head thumb screws m4x.07mm, 25mm long (92581a280 ea) 4-stainless nut, m4x.07mm (94150a335...

cg_trader

$12

Bunton 4 - Light Kitchen Island Geometric Pendant

...de base architecture architectural lighting lighting pendant kitchen island kitchen island light bulb light fixture pendant light

grabcad

free

RASSOR Convergence Collector

...aluminium sheet, bent and fastened with rivets and/or machine screws drive rods are included to increase stiffness. drive rods/hub...

cg_trader

$89

Subaru Impreza center pod housing for LCD screen | 3D

...format stl, obj, 3mf install you don't need any screws or adhesives to install the housing. it is a...

grabcad

free

Bathroom Mop

...lining with the pin that slides on it. 7. screws used to join the bearing and the metal plate...

3dwarehouse

free

193L6100

...193l6100 3dwarehouse modul mounting plate, wing, 0 mm, steel, screw-on, ha: elongated hole