33 pvc aquaponic 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Aquaponics pvc pipe net pot curved contour by rottenclown
...nkercad.
printer: anet a8 plus
filament: nova pla
supports: none
infill: 25%
lines: 3
print time: around 5 hours
thickness: 0.2mm
thingiverse
free
Aquaponics Filter Cap by EoxKoullik
...is a cap designed to fit on a 1.25" pvc pipe to prevent my fish from swimming into the...
thingiverse
free
Domed Filter Cap for 1/2 inch PVC Pipe by dtroupe2
...is a filter end cap i made for my aquaponic project. it perfectly fits a 1/2 inch pvc pipe...
thingiverse
free
Aquaponics Substrate Barrier Stand for Bell Siphon 4, 6, 8in. by Synthecus
...had the trouble of my substrate getting under the pvc tube barrier that holds the substrate back from the...
thingiverse
free
Bell Siphon by the_remora
...a standpipe and uniseal adapter that works with 1in/25mm pvc pipe. i have been using them for over an...
thingiverse
free
corner bracket for 3/4" PVC by dalemilam58
...bracket to fit on my aquarium to put and aquaponic growing bed on...this is made for 3/4" pvc...it was...
thingiverse
free
Light Bracket Aquaponics for Fish Tank
...an aquaponic system. the aquaponics are in a 4" pvc pipe that sits above the aquarium, allowing the pump...
thingiverse
free
Bell Siphon Endcaps by jup2000
...parts include: top and bottom endcaps (3d printed) 1" pvc pipe 1" pvc pipe coupler (for the top) 4"...
thingiverse
free
Modular Aquaponics Farm (model) by abrokadabra
...the vertical planters are made of 6" x 8' pvc pipes, connected with 2x4s. two 250w hps bulbs hang...
thingiverse
free
Bulkhead - ebb and flow by RHill051
...plan to use 5/8ths inch vinyl or 3/4 inch pvc the threading needs to be printed at a .1...
thingiverse
free
4 Way Wet Diverter for Aquaponics or Hydroponics by ooeygui
...a wet and low pressure diverter designed for 1" pvc pipe fixtures. my intention for the diverter is to...
thingiverse
free
1in and 3/4in PVC Pipe Grilled Endcaps by jup2000
...endcaps by jup2000 thingiverse so after built my fantastic aquaponic system, and introducing some dumb, but very cute tilapia...
thingiverse
free
aquaponic bell siphon by lothlorin15
...nut with adapter to attach to either half inch pvc or to the p-trap (which helps if you have...
thingiverse
free
Flow Constrictor by eussrh
...this version is only sized for 1" or 30mm pvc pipes. pvc adapters can be used to fit other...
thingiverse
free
DIY Bio Filter by 00sufs
...need a danner mag drive pump 300-500 gph, some pvc fittings, some nuts and bolts, a trash can, gasket...
grabcad
free
Typical Aquaponics
...typical aquaponics grabcad pvc pipe bed setup to build at...
grabcad
free
Thin Water Film Rack
...tie wraps or hose clamps. its basically a stormwater pvc pipe with holes bored into it with a hole...
grabcad
free
Aeroponics "Dutch Bucket"
...it. i talked to a guy though. he used pvc sewer tubes, and reported he had great results using...
3dwarehouse
free
PVC Grow Tube Hydroponics / Aquaponics
...nics
3dwarehouse
4' pvc drain pipe 10' long with 2' holes for net pots and 1' pvc drain #aquaponics #hyrdoponics
3dwarehouse
free
Strawberry Tower
...strawberry tower 3dwarehouse vertical pvc tower for plants in an aquaponic system #aquaponic...
3dwarehouse
free
Aquaponics Pipe and Board Module
...aquaponics pipe and board module 3dwarehouse aquaponics 2 inch pvc pipe and board module no...
3dwarehouse
free
Backyard Aquaponics
...aquaponic system. constructed completely out of pt lumber and pvc ...
3dwarehouse
free
Aquaponics Module-Kale
...module-kale 3dwarehouse aquaponics module-kale with board and 2 inch pvc pipe run. - by: chad...
3dwarehouse
free
Aquaponics Module-Lettuce
...aquaponics module for lettuce with board and 2 inch pvc pipe run. by: chad...
3dwarehouse
free
Grow Tube Rack
...grow tube rack 3dwarehouse holds (5) 10' 4' pvc hydroponic / aquaponic grow tubes #aquaponics...
3dwarehouse
free
Hydroponic / Aquaponic Grow Tube
...hydroponic / aquaponic grow tube 3dwarehouse 4' pvc drain pipe 10' long with 1' pvc drain and...
3dwarehouse
free
Uniseal 1'
...this is a uni-seal for transition into tanks with pvc pipe. being use in aquaponics as a simple way...
3dwarehouse
free
UNI-SEAL 1.25 INCH
...this is a uni-seal for transition into tanks with pvc pipe. being use in aquaponics as a simple way...
3dwarehouse
free
UNI-SEAL 3'
...this is a uni-seal for transition into tanks with pvc pipe. being use in aquaponics as a simple way...
3dwarehouse
free
PVC Nipples and Fittings
...and mnpt pipe fittings and tees #pvc_fittings #pvc_nipples #plumbing #aquaponic #hydroponics #pipes #pvc_pipes #mnpt_pipes #pvc_connectors...
3dwarehouse
free
Aquaponics IBC system with wrap-around NFT system
...ibc aquaponics setup with the addition of a 6'inch pvc nft system that wraps around the ibc container. nft...
3dwarehouse
free
Bomba Flutuante para Sistemas Aquapônicos
...roupas, um balde de 18 l e algumas conexões pvc #aquaponia #aquaponics #bomba_lavaroupas #lavar_roupas...
3dwarehouse
free
Canister Filter
...#fish #aquarium #water #waterco credit to 'hst' for modified pvc barrel unions (https://3dwarehouse.sketchup.com/model/29fd8f5e16c3d52d711764120f7217a2/spears-3d-union-sxs-857-012), pressure gauge from sketchup...