22 pumps wedge 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
3d_export
$5
33 wedge boot 2 3D Model
...girl pump shoe leater heel tassel brown baked white high detail seond life
33 wedge boot 2 3d model perfectwirefly 81565 3dexport
thingiverse
free
Yamaha Waverunner VX1100 jet pump wedge by MrMetricMan
...ion, no fan, 100 concentric infill. do not use pla as it is unsuitable due to the poor creep properties and material degradation.
thingiverse
free
car door pry wedge by moonants
...ow you to insert a bar to unlock your car when you locked the keys inside. not as good as a air pump wedge, but cheap and simple.
thingiverse
free
Longboard/ skateboard wedges by JakobGross
...uck and drop-through longboard deck. no additional rising. fits both old school (longboard) and new school (skateboard) mounting.
thingiverse
free
Gas Hold On-Clip by carteram
...wedging the gas cap into the handle. check the legality in your state for these. do not leave the pump unattended while in use!
thingiverse
free
LEGO TECHNIC compatible peristaltic pump by brm
...or cocktail robotics! (in the pics you see the old yellow pump from aquarium supply, but that was too slow, so i printed my own!)
thingiverse
free
Droptrough 2 Topmount conversion by elohh
...d to convert my board from droptrough to topmount and added a 11degrees wedge for better ldp.
this part is not tested right now.
thingiverse
free
ROV Bilge Pump Shroud and Mount by DollarBaySOAR
...ch 8-32 pan head bolt and nut.
this system would meet the requirements for mate competitions where the propeller needs a housing.
thingiverse
free
Coleman drain to Intex Pump fitting by ssteve
...onnect adapter to pool
connect discharge (backwash) line to adapter
open internal safety plug
a wedge is needed to keep plug open
thingiverse
free
280 motor blower / water pump (3-6v) by jimacid
...provide air suction but it does blow air and pumps water pretty good. the impeller shaft tolerance is very...
thingiverse
free
Right angle adapter for Intex air mattress pump by slurked
...quot;get it together" looks like.
† (which is really weird, because you don't actually have a newspaper subscription...)
thingiverse
free
Fuel Pump Tank Nut Tool by rickswirebox
...become your go too tool when working on fuel pumps that use the large round toothed nut as pictured....
thingiverse
free
Nespresso dry / air bubbled / airlocked water line repair by sbromwich
... pull the plunger out if it gets wedged - the reservoir is not quite a vertical unit so the plunger should only go about halfway.
thingiverse
free
Endmill holder/carrying case by fluidDesign
...ills, and a single 1/2" x 3" endmill.
you must print:
1x base
1x top
2x insert-0.25od
2x insert-0.375od
1x insert-0.5od
thingiverse
free
Planting on wall by virenchocha
...ay operate the electronis/electric motor on solar cell.
let me know if you make one and contribute towards 'greener home'
thingiverse
free
Kiolia's Double Bowden-Cooled Lightweight Kossel Effector for Trick Laser 3/8" Barbells by Kiolia
...w also know that you can swap fan pins 7 and 9 to drive your part cooling off the fan_1 pins. if you're curious or whatever.
grabcad
free
Skateboard Truck Wedge
...can add both angle and elevation into a single part. this makes it easy to install on steep angle ldp setups, without wheel bite.
grabcad
free
Drop in anchor M10
...ol to drive the internal wedge into the anchor
3. insert bolt (m8) or stud through fixture and tighten to the recommended torque.
grabcad
free
Kayak Inflatable seat
...to design with some testing and tweaking. this design has all the elements to become a successful once the bugs are worked out.
grabcad
free
Fast seal
...rmation was 3microns between point of contact and seal gland.this is close to fea deformation regions with litle flexural stress.
3dwarehouse
free
TEL KEL Shotgun: KSG
...gazine is depleted, the user manually switches to the second magazine by pushing the magazine selection lever toward toward it.2]
3dwarehouse
free
JL Audio 10W6 V2 D4 Subwoofer Enclosure for Mazda 3 Sedan Sketchup Vers
...dio #mazda #mazda_3 #speaker #sub #sub_box #sub_enclosure #subwoofer #subwoofer_box #subwoofer_enclosure #ten_inch #trunk #woofer