22 press embed 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Use 3/8th Rod and Acme Nut on PB Simple 1405 by metaled
...to accept the 3/8" acme nut. pause the printer, press the nut to the bottom of the cavity and...
thingiverse
free
Cold Hold - Drink Cooler/Holder by julvr
...while your drinking it. it has cold packs that press against the drink while its resting, but which retract...
thingiverse
free
Elektra Beckum BAS315/4 Dust Collection Shroud by leonardlowe
...around the part, i used a self sticking seal, press it into the opening and screw the shroud in...
thingiverse
free
Micro-Servo Gimbal - Quadcopter/Tricopter etc. by callil
...the gopro hero 3 and hero 2. the micro-servos press into their parts and are screwed in through the...
thingiverse
free
DSPIAE AT-RS Photo Etched Rolling Set Model Assembly Tool Hobby Accessory by shebdim
...of the rolling set groove. using the rolling rod, press down and embed the photo etched into the groove....
thingiverse
free
Pushbutton Child Safety Latch for Cabinets by jbramel
...the button to the right against a spring, then pressng down against another spring. that should be complex enough...
thingiverse
free
Direct Drive by Troldtoft
...reason is that the nut should be heated and pressd into the prepared hole. this embeds the nut without...
thingiverse
free
Form for silicone cast button pad by josefprusa
...from sparkfun etc. it works, but the feel of pressng isn't same as on the monome, i\'ve updated design...
thingiverse
free
Magnetic Door Alignment for 2020 Profile T-Slot Aluminum Extrusion by johnny1234boy
...mine from home depot) steps you will need to press in two magnets into each part. then install one...
thingiverse
free
Heat Set Press For Brass Threaded Inserts by doublec4
...to build the heat set press i designed to embed threaded brass inserts into 3d printed plastic parts. the...
thingiverse
free
AEG / Ridgid Battery to Dewalt Tool Adapter by Loafdude
...the top. pull tighten it with needle nose pliers. press flat with a tool. when soldering press the wire...
thingiverse
free
Parameterized Stadia Controller Phone Holder
...to match the dimensions of your phone (smartphonewidth, smartphonedepth) press f6 to render the detailed model file > export...
thingiverse
free
Garmin Mount MTB - Shorter stem (Remix)
...put an insert easily). the threaded inserts used (m3) are:.https://www.amazon.co.uk/ruthex%c2%ae-threaded-pressfit-plastic-ultrasound/dp/b07zzhl4ry. they are designed for 3d printer parts (plastic) just...
thingiverse
free
Anet A8+ Modified Belt Tensioner by bschenke
...seconds with a small torch or cigarette lighter. carefully press the nut straight down into the hex recess, then...
thingiverse
free
PieceMaker - Build your own board game pieces by mathgrrl
...satisfying "heft". try out the included demo models or press the "open in customizer" button to get started making...
thingiverse
free
SCOUTcorexy XY_Stage XCarriage 8mm YCarriage 10mm HorizontalRods SingleHotend by florinf-ro
...belts can be tensioned with simple screws and dome-nuts pressng on the belt, forcing it into the niche designed...
thingiverse
free
Strandbeest by Fengist
...really didn't feel like sanding it. getting the bearings pressd into place was a nightmare that caused misalignments in...
thingiverse
free
Universal camera arm/mount with customizations for Snapmaker 2 baseplate, linear rail, or enclosure mount, plus Logitech C920 adapter by PoetikDragon
...with good dimensional accuracy. the nuts are all tightly press fit and should be (gently) hammered into place. snapmaker...
thingiverse
free
Printer Bed Level Adjuster Nut Keeper for Geeetech Prusa I3 by DougInAZ
...the arms and the pads that protrude from them press against the print bed carriage and prevent the nut...
thingiverse
free
Sweeping 2-line name plate (text) by makkuro
...the beginning of the .scad file. e.g. text="your text"; press "f5" to get a quick preview. press "f6" when...
cg_trader
free
Forno Fischer Maximus
...with vray 3.00 electric oven fischer maximus embed 56l pressng fischer stove oven electric oven electronics...
cg_trader
free
SearchNPick Animation Picker Free Trial
...of changing the border color, border radius, hover color, pressd color, etc. grid option to enhance precision. powerful search...