20 motor swiss 2 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Airplane Toy by openfly
...plane advertisement. i used 3mm wood. four small swiss motor, 2 button batteries, some double sided tape and some...
thingiverse
free
MicroSwiss DD Cable Bundle Strain Relief by Tonyrsx7
...time securing the cable bundle including the extruder stepper motor cable to create a type of strain relief. i...
thingiverse
free
Ender 5 Upgrade - Direct Drive - BMG
...direct drive. 3.4 - heat sink for 42 stepper motor 3.5 - some of 3mm screws (i will create...
thingiverse
free
Everything I've done on K8200 next by Splivi
...done on k8200 next by splivi thingiverse 1 z motor mount printed and mounted clutch 2 enclosures for electronics...
thingiverse
free
Bedini Style Window Motor (Metric Magnets and Hardware) by Cotton80
...bearings. i highly recommend abec 5+ or swiss bearings: https://bonesbearings.com/bones-reg-swissskateboard-bearings-8-pack the wire and the circuit is up to you....
thingiverse
free
E3DV6 Adapter for Ender 5 plus Microswiss direct drive by Sergentchat
...3*50 mm rode and nut to fastend to stepper motor the holes that are on the fan duct allow...
thingiverse
free
Ender 5/ Ender 3/ CR-10 Micro Swiss Fan Mount by Obeedronekanobee
...the ender 3/5. i modeled a nema 17 pancake motor with this mounting...
thingiverse
free
3D Printed Pulse Energizer For Radiant Energy (5.125" Diameter) by Cotton80
...circuits to pulse energy through the coils. this pulse motor represents a tool to experiment with. i use the...
thingiverse
free
Ender 3 Max Fan Shroud with BL Touch Mount with Micro Swiss Direct Drive Extruder and Hot End by swartztech
...had to share a screw hole with the extruder motor there is one additional hole on the extruder back...
thingiverse
free
Tevo Tarantula 8mm Rod Y-Axis and Printed Bed Support by evil_k
...the mounting holes to allow mounting closer to the motor mount. i printed this in 3dxtech cf petg at...
thingiverse
free
Hot Swap Hot End for Dremel 3D20 (MOUNT AND PCB) by doublec4
...heater cartridge (24v only, 40w max), and the extruded motor connections. rj45 jacks are required to accept the network...
thingiverse
free
BTT Smart Filament Sensor lid - NEMA17 mount by ivan5rov
...have been converted to direct-drive setup where the extruder motor mount on the x gantry is vacant. the mount...
thingiverse
free
Tronxy XY-2 Direct Drive modded from Drivinator by MindlesSnake
...irrelevant! even with the big full size nema 17 motor on the x carriage, it still weighs less than...
thingiverse
free
Micro Swiss Direct Drive for CR10/10S/Ender3 - Smooth Fang Optimized by jlow
...easy to turn and will not slip on the motor shaft. part fan velocity stack - removed some material...
thingiverse
free
Cakewalk3D 3D printed parts by Thibault_Devienne
...parts: 1 connector between the cartridge and the nema motor 2 detachable rings to hold the cartridge 1 carriage...
thingiverse
free
QED Hot End Cooling System with Convergence Part Cooling Nozzle for: Creality CR10 CR10S Pro V2 Ender3 Ender5 MicroSwiss E3DV6 Volcano Hotend 4010 5015 Direct Drive by magnokneeto
...pass the filament to the left of the stepper motor shaft when viewed looking down the shaft will balance...
thingiverse
free
Microswiss Direct-Drive Mosquito Mount and Shroud 2 by susop
...install square nuts into the backplate. reinstall all extruder motor hardware except the bottom left screw. insert nozzle heater...
grabcad
free
Panoramic Stepper Motor Controlled Rotational Plate
...on the brand of camera mount system (e.g. arca swiss manfrotto, etc.) the bottom has a 3/8-16 threaded hole...
grabcad
free
Cakewalk3D 3D printed parts
...parts: 1 connector between the cartridge and the nema motor 2 detachable rings to hold the cartridge 1 carriage...
3dwarehouse
free
1989 Ford RS200 Evolution Rallycross
...also designed by engineers who had extensive backgrounds in motorports, and the engine had a smooth power delivery and...