17 led1 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
LED1 by pachek
...led1 by pachek
thingiverse
bulb reference is ikea ledare e27 (or any other led e27 bulb with not much heat release)
thingiverse
free
Ban the spinners before they start talking to you. by WillemvD
...void loop() { //h digitalwrite(led1,high); digitalwrite(led2,high); digitalwrite(led3,high); digitalwrite(led4,high);digitalwrite(led5,high); delay(t); digitalwrite(led1low); digitalwrite(led2,low); digitalwrite(led3,high); digitalwrite(led4,low); digitalwrite(led5,low); delay(t); digitalwrite(led1,low); digitalwrite(led2,low); digitalwrite(led3,high); digitalwrite(led4,low);...
thingiverse
free
Motion sensing night light by SteveOst
...and after lights are turned on // with motion digitalwrite(led1low); digitalwrite(led2,low); serial.println("light"); serial.print(lightvalue); // if it is dark then...
thingiverse
free
ARMDUINO V1 Open-Source Robotic Arm! by Doctorfizzle
...start = 100; start > 0 ; start--) { analogwrite(led1 start); delay(10); analogwrite(led2, start); analogwrite(led3, start); } } void...
thingiverse
free
OnStep Case for Wemos ESP R32 with CNCV3 shield by chris_r_schmidt
...included for customization space for two 5mm leds - led1 = power led2 = onstep guiding...
thingiverse
free
WS2812 led shade
...infill, no supports. rotate in your slicer part called led1 to face the buildplate with it`s flat...
thingiverse
free
Breadboard Thermocouple Sensor v1.0 by paulliu
...ad595cq c1: capacitor 104 (100nf) r1: resistor 330 ohm led1 red led j1: 2p 5.08 mm screw fixed terminal...
thingiverse
free
(PCB) Auto bed leveling using piezo discs by inornate
...d2 1n4733a do41z10 ic1 ad822r so8 ic2 ad822r so8 led1 (chip led 3528 size) connector (3 pin molex connector)...
thingiverse
free
Fan Shroud Voxelab Aquila - Triple Fan and BLMount by n9jcv
...to the + on led1, then from ground on led1 go to + on led2, then from ground on...
thingiverse
free
24 Volts LED interior lighting by DH1ND
...are each connected from the cathode to the anode. led1 is soldered from the anode to the plus bus...
thingiverse
free
spinner led pov by fatero
...line) { int myline; myline = line; if (myline>=16) {digitalwrite(led1 high); myline-=16;} else {digitalwrite(led1, low);} if (myline>=8) {digitalwrite(led2, high);...
thingiverse
free
Sonoff Decoa Paddle Sensor Modifications by AndrewLHoover
...to serial in and made it led1 instead of led1. the home assistant configuration is as follows but just...
thingiverse
free
DIY PixelStick substitute for light painting by MartinNohr
...that i didn't explain that the bottom led strip (led1 is connected by the handle, not down at the...
thingiverse
free
Tea Gallows with Eagle PCB by Robokasper
...– r9: protective resistor, 150 ohm, smd size 0805 led1 – 8: 3mm, normal leds without internal resistor ceramic...
thingiverse
free
Creality Ender-2 Controller Board (Labeled) by lewtwo
...mount resistors). note that on this board "r25" and "led1quot; are swapped (connected to pa3). microprocessor (u8): "atmega1284p", "au1726"...
cults
free
LED1
...led1
cults
led1
bulb reference is ikea ledare e27 (or any other led e27 bulb with not much heat release)
3dwarehouse
free
tv led1
...tv led1
3dwarehouse