thingiverse

free

Folgertech Kossel Bowden Aluminium Bracket Replacement for 1/8" pushfittings by AngelDMercedes

...ck of the bowden extruder in the folgertech kossel 2020. this one is able to use 1/8" (~10mm) push fittings for ptfe tubing.

thingiverse

free

Kossel effector with 1/8"BST Pneufit adapter v2 by stone2339

...choll (https://github.com/jcrocholl/kossel/). this works out very well - screw in the pneufit while it is still hot preferably.

thingiverse

free

Kossel Hotend Support with probe clamp for LJ18A 3-8-Z by FitzZZ

...p for lj18a 3-8-z or equally huge induction probes for z-leveling. probe can be ~17mm in diameter, get's fixed with m3 screw.

thingiverse

free

Kossel 2020 foot base by ahntorage

...scratching up the aluminum. it also uses m5 x 8 screws with standard tnuts to hold in...

thingiverse

free

Kossel Pro Delta E3D V6 End Effector Version 8 by calviniba

...nd print super slow (30mm/s) to be able to print the overhangs properly with no support. dimensions: arm width: 41mm radius: 30mm

thingiverse

free

Lightweight carriage Kossel by Redi_ska

...carriage kossel by redi_ska thingiverse m3 20-25 x2; m2.5 812 требуется настройка дельтаразмеров,...

thingiverse

free

Kossel Mini Effector 1/8 BSP Bolt through into J-Head Bowden Hot End by mintlin

...3mm or lower layer and 33.3% infill. slice with kisslicer for accurate (tight) fit bsp. 17/04/2014: fixed missing m3 nut holes.

thingiverse

free

Kossel Fan Mount by tjb1

...heated bed. kossel specs - 360mm frame extrusions and 28mm long rods edit: added stl for the effector i...

thingiverse

free

Kossel Mini carriage for MGN12H by jinx

...jinx thingiverse experimental modded from http://www.thingiverse.com/thing:646889 . to use 8 mm...

thingiverse

free

DELTA KOSSEL EXTRUDER ( DIRECT DRIVE ) by dogukaya

...with e3d v6 hotend together. you also need one 822mm ball bearing some m3 screws and an extruder gear....

thingiverse

free

Kossel linear bearing carriage for Trick Laser 3/8" barbells by Kiolia

...barbells already, i designed a pretty rad (if a bit overspecialized) bowden-cooled one: https://www.thingiverse.com/thing:2884959

thingiverse

free

Kossel Magnetic ball stud carriage by wittmason

...by forerunnert but it was built to have the 3/8quot; 10mm balls sunk into the plastic and i was...

thingiverse

free

Kossel printer pen holder by rsh

...pencils and memory cards. assembles with (1) m3 x 8 hex screws (1) m3 t-nuts need remove original part...

thingiverse

free

Pico adapter for Kossel Clear by B3Innovations

...purchased here: http://www.b3innovations.com/ thanks to this helpful google group: https://groups.google.com/forum/#!topic/kossel-clear/c8xeqr8750 ...

thingiverse

free

Power Supply Bracket for Kossel 2020 by engineer119

...cooling fan mount for "power supply bracket for kossel 2020http://www.thingiverse.com/thing:112248 直流電源装置をkossel下部フレーム内部に取り付けるためのものです。 配線の邪魔をしないために穴もあります。 上にヒートベッドを置く場合、排気ファンで冷やされるので、upside-downを使用したほうがベストです。 フレームに取り付けるための材料： キャップネジ m4x12mm + スプリングワッシャー m4...

thingiverse

free

lowered version of Kossel top spool holder by coloursontheinside

...iterations, here's the result. you need some m3 by 8 bolts and some m3 nuts for this to hold,...

thingiverse

free

K800 power panel by trimex

...by trimex thingiverse this is power panel for my kossel xl (k800 frame) 3d printer. t-nut m3 - 4...

thingiverse

free

Magnetic Kossel effector e3d compatible (45mm centers) by wittmason

...delta printer. it's meant to utilize the 10mm or 3/8#39; metals balls and rare earth magenets. i ordered mine...

thingiverse

free

Kossel Mini/XL spool holder 608zz bearing by TommasoEngineering

...on spool sizes (at least that i have come across). you need to print one of each except for the bracket which you will need 3 of.

thingiverse

free

Top Spool Holder for Delta and Kossel plus universal spool holder for 23 - 65mm holes by dTom

...m4 20mm x 6 m4 nuts x 6 m4 8m x 12 m4 t-nuts x...

thingiverse

free

Folger Tech Kossel 2020 top mount spool holder by hideehoo

...didn't have any 8mm rod, so resized to accept 3/8quot; threaded rod (commonly available in the us) and 3/8"...

thingiverse

free

Anycubic Kossel PSU Box by Caverntwo

...t-nut 4x m3x12mm screws for mounting the psu 4x ≥8m m3 screws for the cover (the nut spaces are...

thingiverse

free

Kossel Bed Leveling by Yojimbojpr

...not necessary at all, i went down it to 8 ...

thingiverse

free

Bedclip simple kossel by nitramDelta

...to your liking i also made 6,5 mm and 8 mm there are some more designs on...

thingiverse

free

2020 geared extruder motor mount by rmoro

...mount a geared extruder motor the frame of my kossel xl. the frame is build from 2020 extruded aluminium....

thingiverse

free

Raspberry Pi Case and Mount for Kossel by kevinlo

...mount the case on vertical. ps : update on 19/82014 , add top case support camera flat...

thingiverse

free

Kossel Clear Raspberry Pi WiFi Antenna by barneyj

...amazon basics extension. it has a hole for a 3/8quot; dowel. revised added a base to mount to the...

thingiverse

free

Kossel Effector for E3D v6 Hotend by tobiaskornmayer

...clip quits its duty. the push fit thread is 1/8quot; rp. the overall polycount was also increased and the...

thingiverse

free

Kossel Magball Adapters by 50an6xy06r6n

...magball. designed for a 5mm rod, 8x10mm magnet, and ~3/8quot; magball, but exact values can be modified in the...

thingiverse

free

Circular fan duct for Kossel 800 by jian

...lock‘s position need to be adjusted to avoid touch the fan duct. 2mm space is enough. --cut off the support structure before use.

thingiverse

free

Kossel Light Up by Simonwlchan

...an option to selectively power on the lights. two m3*8 bolts & nuts required for securing on/off switch...

thingiverse

free

Raspberry Pi (Octoprint / OctoPi) Holder for Anycubic Kossel Linear Plus. by Dogbert

...will need two m4 t-nuts and two m4 x 810mm screws. notes: if you want to use it on...

thingiverse

free

FolgerTech Kossel 2020 Spring Bed Leveler by ChewyJoe

...print. also, these are designed to fit the everbilt 3/8quot;dia. 51/64"l springs i got in an assortment pack from...

thingiverse

free

Enclosure and Watercooling Modification for Large Kossel All Metal Delta by DjDemonD

...to enclosed with a watercooled hotend. more detail here http://forums.reprap.org/read.php?178702599,page=8 i have included the panels to be placed around...

thingiverse

free

Tool Holder Strips, 5mm, 8.5mm, 12mm by freeewilly

...my desktop for the tools i use for my kossel while all 3 strips are the same size (40x25x150mm),...

thingiverse

free

Kossel Clear auto calibration probe deployment post by barneyj

...auto calibration probe. the post is a piece of 1/8quot; carbon fiber rod. length of the rod is 50...

thingiverse

free

Kiolia's Double Bowden-Cooled Lightweight Kossel Effector for Trick Laser 3/8" Barbells by Kiolia

...w also know that you can swap fan pins 7 and 9 to drive your part cooling off the fan_1 pins. if you're curious or whatever.

thingiverse

free

Marlin 2.0 Bugfix - Firmware for Anycubic Kossel Delta Plus by ArtieH

...that the default_axis_steps_per_unit for the extruder was misconfigured to 158 instead of 96. sorry for the under extrusion. the...

thingiverse

free

Mini Kossel zprobe clamp by jcdoll

...1) uploaded an stl for the nyloc version. update (9/82013): 1) after running the printer for a few weeks...

thingiverse

free

Anycubic Kossel Heated Bed 220mm holding plates & pads - Laser cut by GordTheRogue

...with a 80w co2 laser plotter at values of 8 for speed and 100 for...

thingiverse

free

Kuro's for Kossel by elmuchacho

...small gear). i removed the ptfe channel on the 3/8quot; push fit as you can push the pte through...

thingiverse

free

Kossel XL/Open beam fillament holder by LarsBe

...it is connected to the open beam with 3 m3*8 bolts and...

thingiverse

free

Kossel removable magnetic mount for endstop based z-probe with zero X/Y offset. Experimental. by paul_delta

...tilting. six 9mm-10mm magnets like these for $4 12-pack http://www.homedepot.com/p/master-magnetics-3-8in-neodymium-rare-earth-magnet-discs-12-per-pack-07090hd/202526371 update: added another version with wider...

thingiverse

free

Female Banana Plug / Binding Post to 20mm T-Slot Holder by blu006

...to a 20mm rail. i used this on my kossel 3d printer to use my printer power supply for...

thingiverse

free

Kossel Mini Custom Z Probe Retractable - 3mm probe by kalazzerx

...a larger retractable to hold a 3mm z probe (1/8 inch brass rod i purchased at lowes. moved the...

thingiverse

free

Larger mounting bracket for top spool holder by RCC1

...of a top mounted spool holder. really liked the: kossel mini spool holder featuring emmett's gear bearing. by chrisparish,...

thingiverse

free

Magnetic balls template for rod delta kossel

...purchased magnetic rods here:https://it.aliexpress.com/item/32979055943.html?spm=a2g0s.9042311.0.0.2ac54c4dlj4q9d and the carbon fiber rods here:https://www.decathlon.it/asta-aquilone-giunco-in-carbonio-160-cm-x-8mm-id_795700.html ...

thingiverse

free

Kossel 2020 tower endcap by rmoro

...i designed in openscad. use two countersunk m4 x 8 mm screws and two hammer t-nuts per endcap to...

thingiverse

free

Anycubic Kossel - Maintenance Heatbed Holder by Master_Aar

...let me know! this just uses two m4 bolts (810mm in length) and t slot nuts. i've attached step/stp...

thingiverse

free

Marlin 2.0.0 for Anycubic Kossel Linear Plus w/ SKR 1.3 and TMC2130

...details: 32-bit bigtreetech skr 1.3 mainboard (replaces the trigorilla 8bit board) 4 x tmc 2130 in spi mode (x/y/z/e0)...

thingiverse

free

Simple Spoolholder for Deltaprinter with some bling, 80mm and 95mm by Coat

...and strong spool-holder for kossel-printers. designed for the anycubic kossel as a replacement for the original spool-holder. the original...

thingiverse

free

DIY | Anycubic kossel filament runout sensor on marlin 1.1.8 by GolDNenex

...ndarnell http://nathandarnell.com/adding-filament-runout-detection-anycubic-kossel-marlin-1-1-8-biqu-3d-filament-detection-module

thingiverse

free

Anycubic Kossel Plus Reinforcement Corner - Escuadrón by MakeTo3D

...a length of 8mm to 12mm is valid. update 09/12/2018 added model in step...

thingiverse

free

Octopi WiFi Camera Case by barneyj

...pi case. pretty much the same thing as the kossel clear case (http://www.thingiverse.com/thing:256960) with a stand. use a 3/8"...

thingiverse

free

Kossel Pro/mini Delta E3D V6 End Effector Version 5 by calviniba

...5/8" thread rolling screws for plastic (amazon) 3x #4 3/8quot; thread rolling screws for plastic (amazon) 3x 5x37mm internally...

thingiverse

free

Kossel Mini Magball Effector with PCB Mount by JohnOCFII

...(if populating all 3 fans with 4 bolts, otherwise (8 ----- 8x3mm (7) (if using dc42 ir probe, otherwise...

thingiverse

free

Kossel LM8UU 1515 extrusion 2.0 by betocabus

...r one that you can use with the original kossel carriage. will upload the new lm8uu mount as soon as possible! hope you enjoy it!

thingiverse

free

Kossel-Mini Frame Panels by makerlibre

...i added spacers for those too. i cut from 3/8 clear acrylic and then added r-20 reflective film (for...

thingiverse

free

Zero-Backlash Magnetic Ball Joint Rod Ends by huntley

...these with my magnetic effector: https://www.youmagine.com/designs/kossel-plus-magnetic-effector and magnetic carriages: https://www.youmagine.com/designs/kosselplus-magnetic-carriage--2 contact haydn.huntley@gmail.com if you need an inexpensive source for...

thingiverse

free

Kossel / Delta Effector with Auto Level by martin19791121

...x 20mm x 7 pcs. m3 x 10mm x 8 pcs. m2.5 x 10 x 2 pcs. pen spring...

thingiverse

free

Kossel / Delta Effector with Auto Level by martin19791121

...pcs. pen spring x 3 pcs. my other design effectorhttp://www.thingiverse.com/thing:138039 ...

thingiverse

free

Enclosure Kossel / Delta 3D printer by jack283

...pply and also the filament as shown in my pictures above. please feel free to comment below if you have any question. have fun!!!

thingiverse

free

duet 0.8.5 / DuetWifi holder and feet for 2020 kossel mini by hackele

...attached both original stls and netfabb-repaired. just in case. 2016-09-10: have just confirmed duetwifi has the same dimensions.

thingiverse

free

Cooling shroud for FLSun Kossel printer with New efffector: Updated by ahpaa

...type. you can use back the original m3 x 8 screws for mounting. just remove the nuts used to...

thingiverse

free

triangular universal wire spool holder by NilsR

...of each triangle. -fits a standard prusa i2, and kossel mini printbed i used a 7.5mm aluminium rod for...

thingiverse

free

Corner Stabilizer Bracket by BobDavis73

...brackets are my way of bringing rigidity to my kossel delta. i don't use auto bed leveling. i recently...

thingiverse

free

Micromake Arduino Mega 2560 + Ramps for kossel 2020 1515 by MicroMake

...控制板底座，适用于欧标2020以及1515架构的铝型材,因为3d打印机精度不同，提供step文件给大家更改孔位。 使用需要的配件： m3*8螺丝 6颗 m3 t型螺母 2颗 aliexpress store ：http://www.aliexpress.com/store/212817 [our...

thingiverse

free

Wade Extruder converted to bowden for 1/8th inch pneumatic fitting by mdroman

...i put this on the top of my mini kossel and it works great. other parts are the same...

thingiverse

free

G2S MAGNETIC MOD - FULL SET by Pizzu_NOART3D

...a lot.... m3x10 - m3x30 - m4x20 n.b. effector kossel style & effector kossel style_flow support you must print...

thingiverse

free

Mini Kossel Basic Dual Extruder Effector by kkronyak

...holes optional m5 thread or non-threaded holes for npt 1/8quot; / m10 push fit adapters (i use npt pipe...

thingiverse

free

MegaTronXY X1 by tlmxcpmpp

...one print. so i am using my remaining delta kossel 180x330 printer to print the parts i need. so...

thingiverse

free

Simple Damper for 2020 flame of 3D Printers(KOSSEL or others). by shink

...square printers. 4mm bolt (spring and flat washer) x 6(8 you can set this in the opposite direction, but...

thingiverse

free

Kossel Mini 4 Wheel Carriage (Parameterised) by ckitching

...resize it to fit larger wheels after buying the 7/8quot; prime line m-6153. you still need the carriage from...

thingiverse

free

Mini Kossel 1.75mm extruder by wallie

...5mm bore 1x stepper motor nema17 1x 608zz bearing 8 x 22 x 7mm 3x m5 washer 2x m3...

thingiverse

free

Prusa Mendel i2 modified x-axis endstop holder by rmoro

...not used any more, now that i have a kossel xl. to print flexible materials, i have decided to...

thingiverse

free

MICROMAKE 3D Printer Delta mini kossel Arduino Mega / Mega 2560 / Due Drilling And Mounting Plates by MicroMake

...screw 5 t m3 type nut 2 aliexpress store ：http://www.aliexpress.com/store/212817 [our...

thingiverse

free

Remix of Filament Guide Tube to convert to openscad and make Parametric by GeoDave

...am converting the parts that i need for my kossel from this project to openscad, but thought i would...

thingiverse

free

Parametric openscad Remix of Universal stand-alone filament spool holder by GeoDave

...is a remix of the parts needed for a kossel 2020 printer. this was remixed from: http://www.thingiverse.com/thing:508896 for the...

thingiverse

free

Kossel MK2Y (220mm) heat bed clips by Simonwlchan

...short m34 top screw with a m38mm. added 6 m3*8 screws to lock the top plate in place. installation:...

thingiverse

free

Kossel Z-probe mount by optical switch by samrobser

...x 2pcs 7). m3 x 8mm x 2 pcs 8. m3 nuts x...

thingiverse

free

Lerdge auto power module case by PeterG79

...on the 2020 extrusions on the side of my kossel lerdge power module:https://www.aliexpress.com/item/lerdge-3d-printer-power-monitoring-module-continued-to-play-printing-automatically-put-off-management-module-for/32818896817.html it's designed to use m3x4x4 brass...

thingiverse

free

Duet Wifi Board Mount for Anycubic Kossel XL, with 5010 Cooling

...you don't use them. hardware needed: 8x m4 x 8m screws (4 for the board, 4 for mounting the...

thingiverse

free

Sliders/Carriage for Delta Kossel 2020 Original Wheels and Openbuilds Part Store V Wheels by sysimgrp

...original nylon wheels that come with the kit. requires 8 mm spacers. see my delta 3d printer modification for...

thingiverse

free

Kossel Mini 4 Wheel Carriage by rsee360

...lock nuts from a previous project so i used 18 screws and 12 lock nuts and 6 standard m3...

thingiverse

free

Flying Extruder for Kossel Mini (Deltas) by boksbox

...is used for the scad file, for "tapping" a 1/8 bspt thread. if your fitting is different, use this...

thingiverse

free

Top Spool Holder for Delta and Kossel by OSUaeronerd

...if you want tp print without support. my anet a8 was able to do decently well with the sloped...

thingiverse

free

Kossel Filament Holder by timbombadil

...of required bearings is 608 zz. the dimensions are 822*7mm in theory the parts should fit "out of the...

thingiverse

free

J-Head Mount for Rostock Platform by meeker

...this is a modified version of mattschoenholz's "easy adjustable rostock/kossel j-head mount". after printing mattschoenholz's version i realized that...

thingiverse

free

anycubic delta 360 nozzle cooler by juhyukhong

...360 nozzle cooler by juhyukhong thingiverse for anycubic delta kossel printer. the cooler they give at the first place...

thingiverse

free

Monster Kossel v2 by goeland86

...here it meets the 2060. it works plenty well if you put 3 of them in place on a 1m length, one in the middle and one at each end.

thingiverse

free

Tevo Tarantula case mk1 by Dark_Horus

...the case. you need to use reset button from kossel mini smartlcd-case by schlotzz - http://www.thingiverse.com/thing:320117/#files dimensions of the...

thingiverse

free

Folger Tech Kossel 2020 Rod Arm cutting Jigs by GeoDave

...me. i screwed the jigs onto a 2x4 using #8 screws & put a short piece of 1x2 at...

thingiverse

free

Makerfarm I3V or I3 8 Inch Y-Motor Bracket for Dampener by Apru

...i3v has become nearly as quiet as my mini kossel with...

thingiverse

free

3 in 1 out Hotend Conversion, Anycubic Linear Plus Kossel Printer by wt808

...tps://www.thingiverse.com/thing:3282446 for required reading, tips, and information on adding extruders for multi-color printing.

thingiverse

free

Marlin 1.1.8 Bugfix - Firmware for Anycubic Kossel Delta Plus by ArtieH

...e advertised height of the anycubic kossel delta plus. this should eliminate a z probe error that can occur from auto calibrate.

thingiverse

free

Custom Large Metal Kossel Delta by DjDemonD

...i have enclosed and water-cooled this machine details are athttp://forums.reprap.org/read.php?178702599,page=8 i will add some stls specific to the enclosure...

thingiverse

free

HE3D K200 HotEnd Assembly by mjf55

...good delta, but is slightly different from the 'standard' kossel based machines. as for the kossel, i am using...

thingiverse

free

2020 Mount for RP Camera by jbanion

...raspberry pi camera on 2020 extrusion. designed for the kossel plus and raspberry pi octoprint installation. i went with...

thingiverse

free

[ABORTED] Cherry Pi IIIs 320x700mm by DarkoDDio

...:-)http://it.aliexpress.com/item/10pcs-lot-5-27-6mm-nylon-shower-door-roller-bearing-pulley/32259637920.htmlhttp://it.aliexpress.com/item/1pcs-mute-fan-5015-5-cm-black-brushless-cooling-humidifier-centrifugal-blower-fan-2-wires-12/32349434707.html wheels: http://it.aliexpress.com/item/10pcs-lot-5-27-6mm-nylon-shower-door-roller-bearing-pulley/32259637920.html fan: http://it.aliexpress.com/item/1pcs-mute-fan-5015-5-cm-black-brushless-cooling-humidifier-centrifugal-blower-fan-2-wires-12/32349434707.html microswitches: http://www.ebay.it/itm/10x-microswitch-12x6mm-finecorsa-a-leva-deviatore-pulsante-micro-limit-switch-/131468873963 rods balls: http://it.aliexpress.com/item/12-pcs-lot-reprap-delta-kosselk800-drilling-trimming-ball-steel-ball-thread-ball-m10-m8/32356383178.html rods: 6mm aluminium tube from local brico store first...

thingiverse

free

BLTouch Mount for Kossel TwoFan System by Bise

...散熱管風扇。 一個 bltouch 探針，一組 e3dv6 噴頭組和一個鋁合金效應器 。 m3 x15 圓頭內六角螺絲16個，m3螺母8。 bltouch 附贈的螺絲兩組。 還需要一小片隔熱棉以隔絕儲熱塊與風扇罩之間的熱度。 3.此檔案中包含的列印件為： 側吹風扇口 x2 個，不需使用支撐。 風扇座a/b兩個組件 ，需使用支撐。...

thingiverse

free

Folger Tech Kossel Belt Guard & Corner Opening Cover Plate by GeoDave

...instead of using a t-nut. you can see a 8quot; black wire tie on the left cover of the...

thingiverse

free

Power Connector Housing by sfcorrell

...to the “2020” extruded rail base used on all kossel delta printers along with a trim piece which hides...

thingiverse

free

miniCore - Cartesian 3D printer KISS principle by leving

...rj4jp-01-08 xy: 2 x gt2 timing belts (those from kossel mini build work perfectly) 8 x 608 bearing 2...

thingiverse

free

[FolgerTech] Kossel Magnetic Upgrade - V2 by jartz

...the 12mm effector picture is this thingiverse object: ** http://www.thingiverse.com/thing:78379 ...

thingiverse

free

ANYCUBIC Delta/Kossel Mini/Plus Towers Reinforcement by enry68

...o from a friend that has installed my solution also into a pulleymini version and it works fine. thanks for the photo kevin david

thingiverse

free

220x525 Delta by tlmxcpmpp

...220x525 delta by tlmxcpmpp thingiverse i love my original kossel delta printer, but i hate that it only has...

thingiverse

free

Better Blower for Anycubic Kossel by charlesmouse

...is also added insulation for the otherwise exposed pcb. 8 unscrew the old blower and reusing the old screws...

thingiverse

free

Customizable accessorie Cryptstone by shivinteger

...attribution - share alike [8] thing title : folgertech kossel magnetic upgrade [8] thing url : http://www.thingiverse.com/thing:965983 [8] thing...

thingiverse

free

Tevo Little Monster linear rail upgrade parts by mlinuxguy

...plates work fine on all the 20mm * 20mm mini-kossel shuttles that i've tested and allow you to keep...

thingiverse

free

Parametric 3 x 40mm fans and led effector for e3d v6 (Delta/Kossel) by DeltaQ

...only use 4), 4 x 25mm for fans and 8 nuts. 2 x 5mm ultrabright white leds (and resistors,...

thingiverse

free

2020 power distribution box

...box thingiverse introduction i have recently built an anycubic kossel linear plus, and decided that i needed some leds...

thingiverse

free

Kossel magnetic z-probe mount with zero X-Y offset to avoid effector tilt problems/errors. Tested 100%. by paul_delta

...- just print this adapter http://www.thingiverse.com/thing:1195525. how it works: https://www.youtube.com/watch?v=8hy3m8qltg ...

thingiverse

free

Kossel Pro E3D end effector version 3 by calviniba

...5, which ive uploaded under a new part page. http://www.thingiverse.com/thing:184149 ...

thingiverse

free

ezt3d - Upgraded Controller MKS Gen_L by BilboBoggles

...display, then i might rebuild it with a full kossel stock frame, the acrylic is easy to...

thingiverse

free

Delta Effector with 5015 Fan and Auto Calibration by TheThadJenkins

...a remix of "e3d v6 effector for micromake delta kossel v2 (with 5015 fan)" by algenist (https://www.thingiverse.com/thing:3706236). i’d mark...

thingiverse

free

Extra Large Delta Printer with 450x450x450 print area by tlmxcpmpp

...sway. you can use the exciting wheels from your kossel 800 delta. this is a build in progress so...

thingiverse

free

E3D v6 dual 25mm cooling fan holder by goeland86

...and 2x25mm cooling fans on the side under my kossel mini...

thingiverse

free

Magball Carriages for Kossel printer with 2020 extrusions by JohnOCFII

...m3 nyloc nuts to secure the three axles. 2 3/8quot; ball studs (from haydn huntley - see above). 2...

thingiverse

free

KHAT - Kossel Hotend Attachment Tool

...to crimp the molex micro-fit 3.0 pins using a sn-28 dupont crimper, being very careful to not crimp past...

thingiverse

free

Happy Baby Tag by shivinteger

...0.00%, e: -0.36%, f: -0.53% [+] preparing : mod kossel carriage r2 [+] rotating object = mod kossel carriage...