27 keep fpv 16 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Furious FPV Moskito 70 propeller guard by Igb
...bit more fragile (on pla), but perfectly usable to keep propellers safe and resist light to moderate...
thingiverse
free
ECX Temper RC Crawler Exoskeleton (FPV Protection) by SubBass100
...to design it as strong as i could while keepng it light and non intrusive for signal propagation. i've...
thingiverse
free
AstroX X5 Johnny FPV Runcam Micro Eagle Mount (Race Version) by gregframe
...the astrox x5. they really protect your gear and keep it a little cleaner inside. however i wanted to...
thingiverse
free
AstroX X5 Johnny FPV Runcam Micro Eagle Mount by gregframe
...the astrox x5. they really protect your gear and keep it a little cleaner inside. however i wanted to...
thingiverse
free
Micro X Quad by DoubleTap_FPV
...with the front arms splayed out a bit to keep the props out of the camera view. there are...
thingiverse
free
MXQ 105 Micro FPV Quad by scottyorr
...for tabs to glue to your batteries to help keep them in place. update (6/19/16): i had a request...
thingiverse
free
Eachine Twig Arm Protectors
...make sure they fit, and the motor screws are keepng them from being flush. will install them for real...
thingiverse
free
DAwhoopy80 by DAquad
...improves. when designing a micro quadcopter you have to keep it light as possible and with my setup i...
thingiverse
free
Tweaker 180 FPV Quadcopter by KiLLiN-TiMe
...in place. works very nice for cable management and keepng the wires out of the props. left the older...
thingiverse
free
![[COMPLETE] Fatshark Battery Clip by jpacman](/t/8869641.jpg)
[COMPLETE] Fatshark Battery Clip by jpacman
...and i will try to refine it more so keep checking back. battery is a 1300mah 3s 25~50c turnigy...
thingiverse
free
Crossfire Quadcopter Mod compilation by MiguelAlvarez
...adding remixes to mikeyb's crossfire quadcopter, i decided to keep all my mods in one thing. here is a...
thingiverse
free
Micro 105 FPV Quadcopter - 8.5mm Motors, Micro Scisky by punkkills
...the alpine drones micro h. my goals were to keep it crash resistant, light weight and offer good protection...
thingiverse
free
NANDRONE QUAD 2017 by nandinho84
...to give me some motivation, please tip me to keep me working motivated. maybe i'll make an instruction manual...
thingiverse
free
OPEN QUAD TANK by MacaroneePony
...printed parts and eliminate purchased hardware whenever possible to keep it cheap -printing material suggestions for current files everything...
thingiverse
free
Leader 120 Canopy by Ipoc78
...swift 2 fpv camera. the goal here was to keep the leader look but also provide proper fit and...
thingiverse
free
Simple V-tail quad copter by slowjoe170
...correct cg and it has routing slots that help keep the wiring a little neater. i haven't tried it...
thingiverse
free
HF210 FPV Racing Drone by HXLMES
...tie and antenna (image 10) from your rx to keep it upright and away from the props (no need...
thingiverse
free
FPV Single Axis Gimbal for ImpulesRC Alien and Similar by Mchaos
...into the o-rings. it should fit snug enough to keep the camera in but still allow it to pivot....
thingiverse
free
36" Northern Pike RC Airplane (It Flies!) by localfiend
...toss and a good toss look like. i'd recommend keepng the throttle down until the plane clears your hand....
thingiverse
free
Sonicmodell AR 600 Mini Aerodynamic Bicam Kit by Mateyhv
...parts list nose ueagle2 loris4k: extends the foam nose, keep aerodynamic profile, moves cameras forward to maintain cg, improves...
thingiverse
free
300mm Micro brushless 3d printed wing by btnewman
...best be printed on its side with supports, to keep the grain of the filament the strongest for the...
thingiverse
free
TRiFORCE Remix of Switchblade and Trident by filicia22x
...go get the part alone here http://www.thingiverse.com/thing:2003212 thanks ill keep making it better! oct 2 2016 update: after printing...
thingiverse
free
T6 / Y6 hexacopter by Brendan22
...coaxial design (2 motors per arm) provides redundancy to keep flying in case of an esc, motor, or prop...
thingiverse
free
Another Arm for HFM Totem Q250 and Eachine 250 FPV Racer by DougInAZ
...the original. abs should take a bigger hit and keep going. i made the following changes from the original:...
thingiverse
free
X-132: The Ultimate Sub 250g 2-3 Inch Brushless "Monster Whoop" Micro Drone Frame Kit by Karamvir_Bhagat
...4 in 1 speed controllers or who want to keep auw to a minimum. these designs were intended to...
thingiverse
free
X-129R "Monster Whoop" - Micro Brushless 3D Printed FPV Quadcopter Drone Frame Kit by Karamvir_Bhagat
...points to lock in place. if you choose to keep your stack straight you will need to mount through...
thingiverse
free
Rasptop 2.0 The Better Raspberry Pi 7" Laptop *Source Files Included* *UPDATED a lot* by morganlowe
...me know or search the item. the battery one keep changing. you want a 10,000mah booster pack with a...