thingiverse

free

FRSKY X-LITE STICK ENDS by giek2000

...fit over the existing stick ends. no supports needed. infill 100. print in tpu or alike @...

thingiverse

free

frsky taranis nuts by zokizo33

...taranis x9d (m6 threads) nozzle 0.4 layer height 0.1000 infill ...

thingiverse

free

Pull support extension Frsky Taranis X9E transmitter by Ariebaas

...thingiverse extra extentions for taranis pull transmitter. abs 100% infill ...

thingiverse

free

Rotary knob for Frsky Horus X12S by SAGEA

...in 1 rafts: no supports: no resolution: 0.1 mm infill : 100% bed heated : 90° (borosilicate glass) abs...

thingiverse

free

Frsky X9 lite gimbal protector by Lugovin

...frsky x9 lite gimbal protector by lugovin thingiverse printing: full print with 4x6x6 walls/top/bottom and 20% infil speed - 30

thingiverse

free

FrSky receiver insert/tray by leadpan

...when swapping out different rx from plane or wing. 15%infill click...

thingiverse

free

S500 Frsky Antenna holder by mowbs

...to your s500 rails. printed at 0.2mm layer 30% infill in...

thingiverse

free

FrSky Taranis X9D Gimbal Protector by CABsterFPV

...temperature: 220°c glass bed temperature: 50°c resolution: 0.20 mm infill 20% print speed: 35mm/s support: no  follow us:...

thingiverse

free

FrSky XM RX Stack Holder by Daubut

...barely pokes out the bottom. print in abs 75-80% infill ...

thingiverse

free

Rotary knob 2 for Frsky Horus X12S by SAGEA

...rafts: yes supports: yes resolution: 0.1 mm or below infill : 100% bed heated : 90° (borosilicate glass) abs...

thingiverse

free

FrSky Transmitter Wall Mount by Irishnick86

...print with supports, with file on it's side 100% infill remixed from ledrib's spektrum radio wall mount...

thingiverse

free

Module bay cover for JR, FrSky X9D, Jumper T16 etc.

...the .f3d (fusion 360) files available. material: pla, 20% infill no...

thingiverse

free

MICRO RX 4 CH CASE (FR-4 CH PWM-PPM) FRSKY by marcops

...frsky by marcops thingiverse da stampare in risoluzione 0,1 infill 100. bloccare il tutto con un poco di colla...

thingiverse

free

Frsky XJT mount for Graupner mc22 by meltair

...mount. 2 perimeters, 3 botom, 2 top layers, 20% infill ...

thingiverse

free

Turnigy 9X Antenna Mount for FrSky DHT internal Module by jc61990

...any where. i printed mine with 3 shells, 15% infill .20 layers and supports. took about 20 minutes at...

thingiverse

free

Bixler Hatch Cover With optional FRSky Antenna Holder. by Damage

...the fuse. i printed it in abs with low infill i recommend 10-20% in order to keep it light...

thingiverse

free

Project399 Super G Plus R9 Mini MM receiver hammock mount by cjdavies

...whole receiver + hammock. print in tpu with 100% infill ...

thingiverse

free

FRSKY X9D BATTERY by BombRooster

...ering and spade. star may need minor sanding but should push fit into the space tightly and not need anything else to secure it.

thingiverse

free

Micro Quad 125mm 10G FPV | Beef's - VA1100 - FrSKY by chriskonieczny

...of hot glue. when printed in abs, with 60% infill its very flexible and only weighs 10 grams. unfortunately...

thingiverse

free

Turnigy 9X module plate by Ellipsis

...of the transmitter. please use at least 60% of infill resolution is not critical - you can use what...

thingiverse

free

FrySky Taranis 9XD long Stick by quadFlyer

...easy to install and remove. print it with 50% infill 2 shells and 0,11er layer more information about the...

thingiverse

free

Quad frame by touchthebitum

...3s 800mah lipo and fpv gear pla : 50% infill tpu : 50% infill flight control : piko f4...

thingiverse

free

TBS Crossfire Immortal T mount for Apex by doctor_hs

...designed to be lightweight, weighing only 0.74g (at 20% infill, and is secured with two zip ties. i believe...

thingiverse

free

Remix of FrSKY Aerial Mount by LV-426

...aerial to come through. printed at 0.20 - 50% infill - with raft - and support 1.5mm it is...

thingiverse

free

Frsky X-Lite stick gimbal ends by darthskids

...wall layers, 0 top and 0 bottom layers, no infill and a brim. best filaments are any with filler,...

thingiverse

free

FrSky R-XSR 20mm Stack Mount

...wall line count: 3 perimeters top/bottom thickness: 1.0 mm infill doesn't matter supports:...

thingiverse

free

FrSky Xm+ mount, for Moka Gryff by Gandalffpv

...or all other drones racers. better to use full infill and thin layer (0.09 for example) as well as...

thingiverse

free

Full Speed Leader 120 Antenna Mount by Mike-vom-Mars

...shrink tubings (also as shown in the pictures). no infill required. full speed leader 120 mini quad:...

thingiverse

free

FrSky X-LITE Stick Caps / Extenders by Mike-vom-Mars

...use supports (build plate only), 5mm support line distance infill 8% use a raft for good...

thingiverse

free

FrSky S6R Calibration Block by BlueWing58

...10% infil (gyroid) and 3 layers all round, fits nice and snug and you can see the calibration light easily. weighs just over 18g.

thingiverse

free

F280dr quadcopter by crysis_ps

...the plastic details is near 130-140 gramm with 100% infill it is printed abs, but in future i'll want...

thingiverse

free

TBS Gemini Antenna Mount, FrSky D4R-II by WiliM

...mine on a solidoodle 4, at 0.3 resolution, 1.0 infill i hope you like it and find it...

thingiverse

free

Frsky Horus X10S Double Battery Tray (2x 18650) [RMX] by xxDvDxx

...abs for temperature resistance. brim 5 mm all around infill 25%. on my anycubic i3megas i usually print abs...

thingiverse

free

FETtec Drift Car - 20% wider by _ErrorAsh

...following print settings: chassis: tpu (sainsmart shore 95a) 100% infill 0.16mm layer height shell: pla (bavafil black pla) 3...

thingiverse

free

Peon230 - Quadcopter by Tech2C

...-top and bottom frames, hdcam and fpvcam @ 30% infill x 1 of each -arms @ 100% infill x...

thingiverse

free

Ultimate Armattan Rooster Collection (R-XSR, TBS Crossfire nano, AKK X2 Ultimate, RDQ Mach 2, GoPro Session, LED strip, Antenna) by Andris8888

...is in final, printed with pla, no support, 20% infill i use the rdq mach 2 as a vtx,...

thingiverse

free

ZMR Insect antenna holder by anansi22

...cyclops insect. print with abs or whatever 0.25/0.27mm, 15% infill in 8 minutes - no supports. used a bit...

thingiverse

free

Minimal 3D Printed 4" Brushless Racing Quadcopter by RCFPVFlight

...https://www.youtube.com/watch?v=hofmfq3uw7y i printed this using pla with around 20% infill shopping list for the components shown in the video:...

thingiverse

free

3D 85 brushless by anton610

...other parts:https://extrudr.eu/collections/bdp/products/extrudr-green-tec-red print it in 0,09, 6 perimeter, 60% infill 8xm1,6x5 6xm2x5 4xm3x5 nylon you only have to drill...

thingiverse

free

Micro 115mm FPV Quadcopter, HS1177, Piko BLX 3" quad by glef

...a few features specially tailored for 3d printing. (100% infill stiffness added by using ridges along the arms. sunken...

thingiverse

free

Quad Copter APM with modular system by gunman0

...4 channel cppm receiver. maiden flight:http://www.youtube.com/watch?v=7ptw4cz74e0 i printed 20% infill abs w/ 3 perimeters in...

thingiverse

free

XRace360 Copter by Bitfrost

...printed in abs or nylon with more than 40% infill rate and honeycomb pattern. hardware of my copter: 3d...

thingiverse

free

Frsky Taranis X-Lite 18650 battery adapter by AndreR

...liding "lock" groove on the print. that's it, add 2 18650 batteries and screw the ends onto the x-lite and turn on.

thingiverse

free

HexaMicroFly by reparator

...printed in petg from dasfilament in safety yellow color. infill 25 %, no support 2 perimeters in vertical shell...

thingiverse

free

Micro Gentle Lady by N827TM

...files are for 300x300x400 printer. i used zero percent infill aircraft specifications: wingspan: 36 inches / 914mm weight: 7.8...

thingiverse

free

Acrobrat accessories w/ dual camera mount

...in your slice, use a 0.4 mm nozzle, 30-40% infill or more, low-speed to ensure good lamination. installation first,...

thingiverse

free

Armattan Mongoose VTx and Rx tray by Darkstar77

...print in material of choice, i've used pla. 40% infill supports only touching the build plate for the first...

thingiverse

free

220X by KAD370

...resolution for better results and use at least 50% infill or more. update 23.08.2016 just changed engine holders and...

thingiverse

free

Impulse RC Apex Parts Kit by WING_Ducky

...quick to print (around 15 minutes with 30 percent infill at 0.2mm layer height - though it will vary...

thingiverse

free

Carlandoo - 1:32 Fully 3D printed crawler

...alisto: https://www.thingiverse.com/thing:2997226 wheel hub based of work from: samdsx: https://www.thingiverse.com/thing:3454206

thingiverse

free

Semi Ducted Micro Frame (Beecheese Frame V2) by Noctaro

...printer: printrbot plus rafts: no supports: no resolution: 0.2 infill 100% more from 3d printing view...

thingiverse

free

RC KTM Ascender by Phil_Maddox

...2g.html rx = frsky dr4ii http://www.banggood.com/frsky-d4rii-24g-4ch-accst-telemetry-receiver-p-929069.html?x9120314803172015043

thingiverse

free

Ultimate Skylark Antenna tracker all in one box! by toolman207

...the video and rc control gear. printing the parts infill can be pretty much whatever you want it to...

thingiverse

free

75mm micro quad frame by Mulder

...shatter, even though it appears tougher. print at 100% infill to get maximum toughness. weighs about 6g. use 380mah...

thingiverse

free

FRSKY Taranis Q X7, FPV LCD monitor folding mount V1 by kiloOhmcom

...pla of about 1%. so, just print at 40-50% infill and it should fit. if using abs, you might...

thingiverse

free

XBL117 SLY.VESTER pack by earlynerd

...fpv quadcopter! all together they weigh ~4g, depending on infill i really like the xbl117 frame design, but after...

thingiverse

free

Peon Quad 230 reimagined by jimbob4040

...the two different colors. i would print at 100% infill i just added ("new top canopy fixed") a new...

thingiverse

free

FPV-Rover V2.31 (Tank)

...bevel gear 66x track (recomend vertical print with 100% infill 66x pins 1x top (v1,v2 with glue lock or...

thingiverse

free

Arkangel runcam micro pod by jr555se

...works. printed in nylon 0.4 nozzle and 0.2 layerheight. 30%infill right now but havent flown it yet. rain,snow,work,illness.. i...

thingiverse

free

X8 Drone by mlenzi18

...10.5". the 3d printed objects were printed at 100% infill in pla. this could likely be reduced to save...

thingiverse

free

Tweety 2.0 - 130 Sized -True X - FPV Racing POD by bitwise

...realy rigid and durable won't break easy, printed @100% infill abs.. p.s. if you download this project, please like...

thingiverse

free

Semi Ducted Micro Frame (Beecheese Frame V3)(cam mount integrated) by Noctaro

...based on stylesuxx´s awesome cheeseframe. print it with 90-100% infill you can print it pretty fast with still good...

thingiverse

free

BIF RC Lantian X3 Upgrade Kit by Banana_Science

...mount the frame shipped with wasn't printed with 100% infill or nearly enough shells, causing it to split in...

thingiverse

free

NoTankS - 3D Printed RC Tank by swepet

...in regular pla. track segments are printed with 100% infill everything else with 20%. the covers and bottom are...

cg_trader

$3

Receiver bind switch | 3D

...settings for pla nozzle temperatures: 195° plate temperature: 50° infill 50% drone fpv flysky frsky racing freestyle toy frame...

cg_trader

$3

Pedestal | 3D

...settings: material: pla nozzle temperature: 195° plate temperature: 50° infill 15% support: for base e rods pedestal 3d printed...

cg_trader

$3

Flexible third hand | 3D

...settings for pla nozzle temperatures: 195° plate temperature: 50° infill 50% drone fpv flysky frsky racing freestyle 3d hand...

grabcad

free

3D Printed Brushless Whoop mini FPV drone

...esun pla+ filament at 0.1mm layer height at 33% infill (just my preference) without any supports or rafts on...

cults

free

BIF RC Lantian X3 Upgrade Kit

...mount the frame shipped with wasn't printed with 100% infill or nearly enough shells, causing it to split in...