20 hole splicer 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Filament Splicer with 2mm hinge holes by rladams65
...s excellent design and made the holes smaller so i could use a piece of filament as a hinge pin. you need 2x of the [hinge] part.
thingiverse
free
Splicer Fujikura 70S+ shelf
...splicing to cool of. i used supports on the hole. i did use a raft for better...
thingiverse
free
Firestorm Quantum Splicer
...fdm printer. on rest of the arm there are hole for mini brooch back bars pins so you can...
thingiverse
free
Filament Splice Helper - splicer by OnTheGulf
...down and the splice will not move through the hole thanks again to trustfm's head design! again, make sure...
thingiverse
free
Filament Splicer by DR2D
...3mm hole and a 5/64” drill for the 1.75mm hole (if you have a numbered drill set or a...
thingiverse
free
Customized Tie Parts (for older machines) by miketishman
...in the middle and the spaces in between the hole. credit to http://www.thingiverse.com/thing:35940 for the clip...
thingiverse
free
Updated Keiser Spin Bike Shelf by cst2112
...supports if your splicer allows you to avoid it. hole information: dia = 5 mm, recesed dia = 10...
thingiverse
free
204 Volt Quick Disconnect Splice Housing by thingengineer
...from the breaker, it is closed off except for hole just big enough for them, so it’s impossible for...
thingiverse
free
Filament Joiner Jig
...of the jig with the filament fed through the hole. now you can use both hands to control the...
thingiverse
free
Filament Splicer by Antwon_Fukwon
...off any large bumps with a razor blade. the hole in the tool without the ptfe cutout is 1.80mm,...
thingiverse
free
Splicer Weapon - Monkey Wrench by madebyCK
...which will be glued (i use 100-grit sandpaper) 2 hole are included in the wrench handle for 1/4" dowels...
thingiverse
free
WanHao Printer 3d - Guide Adapter by chaos51
...break. but the guides don't actually fit in the hole inside the extruder. this "thing" is a small adaptor...
thingiverse
free
Raspberri Pi + HDD Enclosure by dbatkins
...to do that :-) please note, all the screw hole are set for 3mm screws. it's a little tight...
thingiverse
free
CR10S Pro V2 Hot End Light by mettauk
...wiring into the main fan supply (24v). the vent hole in the holder may help keep the led strip...
thingiverse
free
GT2 Belt Drill-Splice Jig by neoCogent
...inserted from the other end and tapped into the hole most likely this won't print well but can be...
thingiverse
free
Short 16mm Film Rewinds by zlp
...flange to shaft tip. push the flange into the hole in the base. (i needed to sand mine to...
thingiverse
free
Splicer Cat Mask (Bioshock) by Annatar2
...mask insert three of the pins in the provided hole. this will help you line up both halves accurately...
thingiverse
free
X-120 - 2 Inch "Monster Whoop" Micro Brushless Racing Drone Quadcopter by Karamvir_Bhagat
...to m3 adapters. you can mount via the arm hole or by rotating the stack to have one corner...
thingiverse
free
XC-120 Patriot - Micro Brushless 2.5 inch "Monster Whoop" 3D Printable Quadcopter Drone by Karamvir_Bhagat
...to m3 adapters. you can mount via the arm hole or by rotating the stack to have one corner...
cults
free
Splicer Cat Mask (Bioshock)
...mask insert three of the pins in the provided hole. this will help you line up both halves accurately...